grinding machine from old hard drive ฮาร์ดดิสเก่าเอาไปทำอะไรไปดู

Рет қаралды 100,694

4 жыл бұрын

#grinding machine from old hard drive
้#howto make grinding machine from old drive #hardwork
LM7805 voltage regulator
ฮาร์ดดิสเก่าเอาไปทำอะไรไปดูกัน ทำเล่นเพื่อความบันเทิง
#harddisk #LM7805
#westerndigital

Пікірлер: 51

@GuptaElectronics53 2 ай бұрын

Nice videos 👍

@NRPAUL-pr9he 10 ай бұрын

VERY NICE MUSIC/NOISE IN BACKGROUND.......

@RaniKumari-bz4gc 4 ай бұрын

Nice bro ❤❤❤

@KenAtCommentPage 2 жыл бұрын

Well it actually works, but on a specific brand of hard drive, I tried this on a Seagate Hard drive, it doesn't spin without the arm. Better find a WD hard drive if you want to do this project.

@Scheepsbouwer 2 жыл бұрын

connect pin 3 and 5 together of the data connector of your sata drive

@rcdmusic0810 Жыл бұрын

Works on Seagate Barracuda 7200 12 with data pin 3 shorted to 5. Still trying to get answer for IDE HDD to be able to spin continously. Any solution yet?🤔

@segmenchannel 2 жыл бұрын

👍

@nightsun152 2 жыл бұрын

👎

@9JCEE Жыл бұрын

Welcome to my CH enjoying

@vladpetr9168 Жыл бұрын

strange... the title of the video does not say that you will have to listen to very cheesy and very loud sounds.

@MrOziwizi 3 жыл бұрын

Hi, is a bit confusing on the wiring, do you have a wiring diagram and do you still need the HDD PCB board?

@mrinmoy8190 3 жыл бұрын

Yes.

@mrinmoy8190 3 жыл бұрын

You have to supply 2 seperate volts in pcb (red + black = 5 volts and yellow + black =12 v)

@Yurgen72 Жыл бұрын

How can I always spin an IDE hard drive? Can I connect some pins like sata pins 2-6? Thank you!

@GuptaElectronics53 2 ай бұрын

Gupta Electronics53

@tatafatahillah5211 3 жыл бұрын

Musicnya brisik

@9JCEE 3 жыл бұрын

Welcome to my CH enjoying

@bladesman123 3 жыл бұрын

It begs the question, if one requires a grinding machine to make a grinding machine, why not just use your original grinding machine to grind whatever you are going grind with your new grinding machine?

@9JCEE Жыл бұрын

for hobby sir haha

@GuptaElectronics53 2 ай бұрын

Gupta Electronics53

@vcccabelski4014 2 жыл бұрын

I did it the same, it runs perfectly but stopped after 20 seconds....

@ikutsal Жыл бұрын

Connect sata pins for data bypass, sata 2.pin and sata 6.pin

@rcdmusic0810 Жыл бұрын

@@ikutsal how about IDE drives, which pins to connect to get it spin continously?

@9JCEE Жыл бұрын

Welcome to my CH enjoying

@gltchgiopiazza3580 6 ай бұрын

@@ikutsal How about ide?

@ikutsal 6 ай бұрын

@@gltchgiopiazza3580 kzbin.info/www/bejne/laG1o3WmfbitgJofeature=shared

@Dancopymus Жыл бұрын

I couldn't figure out how the connections were made.

@GuptaElectronics53 2 ай бұрын

Gupta Electronics53

@__blank__4193 2 жыл бұрын

i did the same steps but when i tried to power it up through ic the motor doesnt rotate and spark comes from both terminals(I have not soldered the adapter wires i connect them using my hand by touching the wires)