Run HDD motor without ESC | uses 7805

[@BlackOpsJuJu]

Nice Very Nice Awesome well Done Thanks for Sharing !!!

[@PhdHung]

[@Mitgardxxl]

5:21 Can u tell me, why we need a Capacitor ? You write it is to Filter... What the 5V Signal looks without that Capacitor and how it looks with a Filter Capacitor. I dont know it. Thank you.

[@PhdHung]

Capacitors stabilize 5V voltage.

[@shonyramses2251]

How I can make ide hard driver run continuously?

[@3333927]

Try to connect pin 1 to 2 and pin 3 to 4. Pin 1 and 2 are the ones closest to the power connector.

[@AkiroDemonSlayer123]

Another great video. And still waiting for mppt 50A

[@PhdHung]

It will take a long time for that video

[@AkiroDemonSlayer123]

@@PhdHung 😥😥😥

[@w.dkalyan6234]

Your grate because i also collected these drives in scrap market but their is no idea to run this motors to use for my project works that's way I buy bldc drive control for it

[@w.dkalyan6234]

Sir please if you don't mine please tell me what is capasitor you used?🤔

[@w.dkalyan6234]

Please don't forget my request sir please..........

[@PhdHung]

just a capacitor. It filters the voltage behind the 7805.

[@imaginaryworld6930]

Damn I congratulate you The best person who did it is you I have seen a lot of people doing it, but most of them cheat and lie, and they are never clear, they are liars. In conclusion, I thank you very much for the clarity, I have to try it ♥👍

[@xsauce3858]

What the point of the voltage regulator ? Can't we just feed 5v to the drive ?

[@NevesProjects]

The hard drive needs both 12v and 5v supply in order to stay turning, the 7805 is so you only have to use one 12v supply for power and not 2 (5v and 12v)

[@pauloinventostube7533]

congratulations 👏 it was very good 👍👈

[@PhdHung]

[@nordicheroxo6162]

and how do you make this on a ATA HDD?, i mean at the ATA conection, what i need to do to spin for ever the motor? now is spin for 10-15 sec and it stops.

[@Techno0070]

Voltage is AC or DC and how much 12 volt or other?

[@PhdHung]

dc 12V

[@dilannethsara]

6:43 what is the wires for IDE hard disk

[@3333927]

Try to connect pin 1 to 2 and pin 3 to 4. Pin 1 and 2 are the ones closest to the power connector.

[@dilannethsara]

@@3333927 I will try

[@osaretininnocentifaluyi7485]

What a brilliant work for workshop tools

[@danhayes5225]

what exactly are those tools ? that is the question as that was not even mentioned in the video.

[@wakeelahmed5225]

bro i have made same like your video but it's not working...

[@liliknuryani556]

hi ..why my HDD/Spindel ..will very slow running and tend when i put something on the disc .do you why..??

[@rifatozdemir7272]

çok güzel oldu emeğine sağlık 7805 iyi fikir

[@Dancopymus]

Hello friend, first of all, thank you for sharing the video. I have a question: Is the HD logic board itself not strong enough for this purpose? I say this because I tried it with the HD plate and, when I go to sharpen, for example, a screwdriver, when I press the screwdriver a little against the sandpaper running on the disc, the motor stops rotating. Thanks

[@mewing_enjoyer]

i buy ups transform with no center tap..how to use for inverter..

[@PhdHung]

Using the H bridge inverter circuit, there is a lot on my channel

[@nsachannel7638]

Nice Work, but not all HDD will like this... I have manytimes to build this but not working on HDD died (not spinning when I give power on it) only work when your HDD spinning when you give the power from Powersupply (spinning and stop) before you try to do this.. to make running constantly you must conect sata conector like this video.. CMIIW, btw keep make about electro bro, especially Simple Inverter It's Very usefull for save the energy.. I fan you from Indonesia.

[@mercedesm.7851]

Hi, ¿Can you use this system for converting a CD rom as a CD player? i got CD Roms with volume and headphones out in front, and i need a way to put power supply.

[@cxxaner]

I always asked how can I run hdd motor they always said use esc driver. I already know that there is an bldc driver in this circuit. I made some datasheet search and the biggest chip on the circuit is bldc driver. I began to be curious how can I get rid of unnecessary component and make pure esc from Hdd. And I couldn't. Maybe you can achieve this and make a video about this. I will be waiting for this. Thanks.

[@PhdHung]

ok, I'll give it a try if I have free time, lately I'm quite busy.

[@11Magaiver]

Placa HD IDE tambem da para fazer esta ligação ou só HD sata

[@efrainvelandia3785]

Bueno, pero que muestren con que adaptador o fuente se conecta.

[@BastelPichi]

3:11 i can see your face

[@Yurgen72]

How can I always spin an IDE hard drive? Can I connect some pins like sata pins 2-6? Thank you!

[@rcdmusic0810]

Got the sam issue using IDE HDD, only runs for 2 minutes, any solution, anyone?

[@elevtrotech1925]

Great job I just wanted to try IRFZ44 based ESD. But your idea should be useful and easy with the connection of 2-6 or 3-5. Thank you

[@SJs-h5s]

What about ide driver wich pen i will short

[@hyperhektor7733]

great , much better , so no esc is wasted

[@jimenezsplaylist4618]

You dont even show where the positive charge leads or where to put it directly

[@Mike_Video]

this process also works for three-spindle motors

[@surachaisuwanapong4261]

Hard drive ide, which pin is straight?

[@محمدالدمني-م2ط]

يا اخي لو سمحت كيفية صنع Esc 30 v وايش اسماء القطع الضروريه لصناعتها وانا منتظر للفديوا اذا سمحت

[@otsmania7342]

how could I make it run a little slower?

[@baniadamtv]

Creative.. 👍👍

[@PhdHung]

[@jazasleman5475]

i have a question please..i want to make 5KW transformer can you help me sir.?

[@PhdHung]

ok bro

[@user-rs8zg8ey2b]

Simple, use two MOT (microwave oven transformers) in series or parallel. The 220V microwave are more power than the 110V versions.

[@Jastejsingh]

Please tell this for a laptop sata hard disc

[@cp1855]

Excellent demonstration I have same HD but Sata socket have 5 pins. Please help Thank you in advance👍

[@cesarluis1703]

1:26 si hacen clic en ese minuto en la barra de avance. aparece una campanita. por que es?

[@eduardocintas]

Te invita a suscribirte y activar todas las notificaciones del canal

[@molychandran7562]

Great job sir... thank you.

[@PhdHung]

[@elektronikhobim6903]

my brother, nice work. i want to ask a question.Can this electronic circuit be made with a new generation hdd

[@XenyQ_OFF]

Yes but need at least 7200rpm

[@ratikantamahapatra8847]

for PATA what to do?

[@mickgi7866]

How to short the 10 pin slave master

[@gurpreet1389]

Pata hdd continuously motor run pin number short pls tell me

[@maivananh1431]

Hôm nào làm cái video cách hoạt động của mấy cái trạm hàn cao tần 400KHz như quick203h hay quick205h đi anh, có sơ đồ hướng dẫn càng tốt ạ vì e làm thử thấy nó hơi bị nóng cái dây tay hàn quá.

[@PhdHung]

ok b

[@TheMunirLaghari]

Sir dvd room ka bhi video bnao

[@MyGirl99]

Hello! What is the rpm/min of a HardDrive motor? Thank You!

[@crashbandicoot4everr]

Usually 5400 or 7200 RPM.

[@jazasleman5475]

well done..💙💙

[@PhdHung]

[@ngjovi8373]

thank you, very useful!

[@codygrose7755]

After two failed attempts and three different 7805's i have acheived a spinning HDD however regardless of jumping pins 2-6 or 3-5 my disc spins full speed then slows to almost a stop then refires and then slows and refires then slows to a stop... it will repeat this process if i disconnect and then reconect the power... any insight would be amazing... im a newbie but loved this project and was pleased i had all the parts on hand... Thankyou!! C.G.

[@codygrose7755]

...Maybe my cap isnt good enough....???

[@hazim38780]

Ceramic capacitors are much better for fast switching purposes than electrolyte caps. Maybe u try 10uF ceramic ones. I hope this helps.

[@magdyandrawes1497]

good gob where's the terminal of 5 v

[@antoniocammarota8061]

Boo è così facile.? Complimenti!!

[@GuptaElectronics53]

Very nice videos ❤

[@dr-gaberibrahim5268]

Draw a diagram or video is of no use

[@w.dkalyan6234]

Hi sir your very grate 🙏

[@PhdHung]

[@gioito7090]

thanks very good 👍

[@PhdHung]

[@shakilahmmed5615]

Good job 👍

[@PhdHung]

Thanks

[@romeoj387]

Is the elco necessary or optional ?

[@Muslim_011]

It is just for filtering the output (5 volt) he used 1000 uf 10 volt but you can use any value like 470uf

[@juditpm]

Se puede con uno de laptop?

[@PhdHung]

i think ok

[@dakshji1428]

which country are you from

[@PhdHung]

VN bro.

[@MuhammadDaudkhanTV100]

Cool

[@PhdHung]

[@user-rs8zg8ey2b]

I still have a hard time believing shorting high speed data lines makes the HDD spin, anyone else try this? I will find a spare drive and try.

[@PhdHung]

yes, shorting the data line will "trick" the hard drive into reading data. However, I am not sure that all drives will work this way.

[@giwangpvcartslamp1349]

Can use diamond ?

[@MyOwntuahur]

Nice post

[@PhdHung]

[@gnahna2611]

You can make in hard data Thank you ❤

[@treasureislandofworld]

Amazing !

[@PhdHung]

[@quyenvan11]

Mình cũng hàn chân 2 với 6 mà nó chạy vẫn dừng

[@manilalpatel7196]

Does not run as shown in your ad

[@scienceandtech7164]

Beautiful

[@PhdHung]

Thanks

[@scienceandtech7164]

Please can you design an ac to DC power supply @30amps and 12v to 60v variable I have SG3525 , Uc3845 ,tl494 ic. Thanks

[@edvaldosantos8029]

muito bom ótimo👋👋👋👋👋

[@electronic7979]

👏👏👏

[@PhdHung]

[@klsonidhanla]

Very nice 👍👌👍

[@prpolidoro]

But your HD is different I have. My HD doesn't have this connector

[@marcocruz263]

HD SEAGATE SATA NÃO FUNCIONA

[@MsAxelfoly]

2-6 and 3-5 it didn't work

[@bishal.dangol]

Waiting for new spy camera

[@PhdHung]

ok bro, wait

[@bishal.dangol]

@@PhdHung ok

[@CLAUDIOSRC9529]

[@RezXNana]

even cheap power suply its can destroy your hdd lifetime. its ok fir just in short time but for long time absolutelly no especially with your expensive hdd

[@TrinhDo27]

Người vn hả?🤔

[@gocchiase8785]

Chưa có video hả a

[@PhdHung]

Mai nhé cưng.

[@TECK2024]

Não precisa dessa gambiarra, vou fazer um video sem nada disso o motor gira numa boa

[@mdrahat8629]

Sir please make welding machine

[@PhdHung]

ok bro

[@KinhKha-lm2zl]

khỏe không em trai........

[@PhdHung]

đang sụt sịt anh :v

[@hihi-xq9rb]

Anh ơi anh làm mạch timer bằng ic555 kích fet cho han cell pin đi ạ

[@PhdHung]

tìm trong kênh có đó em

[@hihi-xq9rb]

@@PhdHung anh ơi anh làm ic lập trình ma em ko có ic đó

[@jedeaojota5362]

Top ssimo legal👏👊

[@nguyenvanthuong7153]

Anh quá tuyệt vời

[@PhdHung]

cám ơn nha

[@ayhanozsy4189]

perfeckt

[@monolito8556]

nice

[@vikaspagare5031]

A1 vdo sir. plz digram

[@الطموحالشرعي]

I did everything exactly like you and it didn't work

[@الطموحالشرعي]

Knowing that it was working before I opened it

[@viciriucandreea5835]

Ok felicitari

[@sandeeppro-sw1fp]

Try moter running and hold finger on screen 2x fast😂😂😂

[@guira538]

Magnifique top

[@PhdHung]

[@monkeh3612]

You know the transistor is useless... -_-

[@dakshji1428]

Your country Vietnam

[@henryramos4205]

No funciona

[@nguyentaniep5524]

ok

[@dariengermanmontesgonzalez7462]

no se aprecia bien.. lo haces solo para ti... como enseñanza es malo... dale capacvidad de maestro.

Tốc độ quay thấp.

[@PhdHung]

cỡ 4 5000V/p

[@Zurab880]

Не морочь людям голову,инженер недоучка..После полного цикла заряд-разряд конденсатора,мотор остановиться..Вот весь смысл...

[@headbanger1428]

It is using an ESC. It's just built-in on the hard drive board. Many people here looking to run just the hard disk motor in different environments that cannot accommodate the hard disk chassis and board. You get a downvote for clickbait.

[@henryramos4205]

Fake

[@Sanjay-eb6fe]

Please don't try this out guys. It will be a total waste of your time. Harddisk spindle motors are Brushless DC (BLDC) motors. Unlike normal DC motors, BLDC motors will not run on a constant power supply.

[@eduardocintas]

HDD board have BLDC they can spin on their own(if not they will not work as hdd). But u need to power by SATA Power Supply with 12v for motor and 5v for controller. Also if they don't detect data read controller will spin motor down to save energy. This mod have 2 parts: 1) 7805 is a regulator capable to give 5V from 12v, so you can use any 12v power supply and dont need a SATA one(cap stabilizes the 5v). 2) Jumping RX and TX data lines, fakes the controller to think there is data transfer and keep motor running. Petty cheap way to make it work at full speed buying a BLDC Driver cost ore than the HDD motor. And making it diy es complicated and need dificult to get parts, 7805 is everywhere and CHEAP

[@eduardocintas]

BTW we can only use full speed, will be awesome to be capable to control speed