Great. Nowadays, this video has been helpful to me. My old 430 is still working
@91786mmc11 жыл бұрын
I just cleaned the relays on my TS-430. Works like a charm !
@markadams139311 жыл бұрын
Had a huge sensitivity difference between 6.499 and 6.5 mhz. Went through the relay cleaning. Only had a 50 ohm resister for around 250ma. Huge improvement. My short wave listening really got a shot in the arm. Great video.
@diveron4 ай бұрын
The AM mode on my 430 stopped working. This technique has brought it back so far.
@roberthopkins80894 ай бұрын
Was just going to replace the batter in my radio.. To my surprise for a 40 year old radio it was still at 3 v... Kenny quality...
@aquarius24353 жыл бұрын
Many thanks for the very nice explained TS430
@mikep951334 жыл бұрын
Finally found the video from N4DA !! Thanks !!
@stevensaylor9430 Жыл бұрын
What a great video. I'm glad I saved this one. Thank you.
@desmondrodney836410 ай бұрын
I find your video on the Kenwood 430ts to be very informative
@Fraiyia6 жыл бұрын
Thanks so much ! Professionally done . I watched this video like a college course .
@turboclub7658Ай бұрын
Great info, just changed my 3 vdc battery with a CR2032 and what a pain to solder the original tags onto it. The positive side with a sandpaper clean and flux soldered no problem. BUT the negative side proved to be annoying with about five times before it was done. TIP Dont pick up the new battery while doing this with metal tweezers.... DOH!, 😝direct short and new battery now 2.8VDC...😱 Replace again as now 14.000.000 on switch on!! Shazbot!
@eogg2512 жыл бұрын
My Lord, this is a very interesting video. you sure put some ime into this. i dont own this radio but i enjoyed it and the information you provided. thank you.
@mohamadsjarifudin56885 жыл бұрын
Thanks Frank, I'm YD1DDC (ex YB1JU) . Your video help me for repairing my Final Unit. Resistor R15 (15 Ohms/0.5W) at the base of Final Q4 is getting hot and burnt. I don't know why. I hope with all information from your video I'll fix this problem. If you have modifications for making TS-430S performance better pse upload its video.
@shuttersound6911 жыл бұрын
Worked like a dream..used a 22ohm 10w..perfect thankyou very much.
@manyacarb82982 жыл бұрын
Beautiful transceiver and nice video !!!
@jamesventura51065 жыл бұрын
Excellent Video, and explanation on where things are and how to adjust or all the other things YOU showed, it was like going to a Class on how to make such adjustments and replacements or adjustments.. Not many Videos On KZbin are this well done... The only complaint was the Focus of YOUR Camera was not very good, but I could make out where things were as YOU Explained how to do things, I have a Kenwood TS 403 and a TS -930S and have some things I will do to them what YOU showed how to do in YOUR Video, Good Job!!!!!!!!!
@evokefrank5 жыл бұрын
Not MY video, but thanks! It's a rip from an old beat-up VHS tape. I contacted the creator, and he didn't have a better copy, or any copy in fact. Uploaded with permission, but that's about the extent of what I know as I'VE never owned a TS430. Thank YOU for visiting.
@pebbles03894 жыл бұрын
the best informative video ever
@osvaldogustavo4 жыл бұрын
Very well made video, Thanks!
@slartybardfarst5211 жыл бұрын
Nice informative video, have downloaded it , gonna save this for when my 430 keels over, thanks buddy
@ironmank9552 жыл бұрын
Wow other than the poor old quality video I just learned a lot
@w.rustylane56503 жыл бұрын
It would appear to me to take the plastic covers off of the transmit relays and clean the contacts while you have the PA out. I would have done that as well just so I wouldn't have to do it again later. Thanks for the video. I will have a working Kenwood TS-430S with the PS-430 dedicated power supply next week and am looking forward to using it when I get my General license as well next week. I also noticed that your radio does not have the FM board installed. I would need to know where the bulb is soldered as I'd replace the incandescent bulb with a 5mm bright white LED. The LED needs to be oriented with + and - solder connections with a current limiting resistor. A GREAT BIG THANK YOU for showing the modification to transmit on WARC as well as 11 meter band and opening up all the HF frequencies. I knew it could be done--I just didn't know how. THANKS again for that. 73 from K9POW in eastern Tennessee.
@eogg2512 жыл бұрын
one more thing i was an electrical and electronic repair man in a steel mill and would suggest when working on live equipment u should remove ur ring from ur finger, gold is a very good conductor of electricity.
@Dmon741011 жыл бұрын
Big help
@ethicalfarmer74245 жыл бұрын
Fantastic!
@mous26411 жыл бұрын
Hello Milton, Great work, just one thing to point: the speaker connection shown in the video is not correct, the speaker connect to the IF board on connector 1 and not to this one, that connector should be to connect the optional FM card. I am trying to make one working, very poor sensibility and scraches when tuning on frequencies with signal. Many thanks for this video, it helps to understand.
@lewsdrisfun70179 жыл бұрын
Just picked one up for $40 not expecting it to work, looked nice but had dead on the sticker, got it home, checked it out, has the AM filter, powered it up & everything works, great receive and spot on freq but display goes blank from 1600kc to 2500kc with no receive. Here the relay kick in.
@grumpyg93503 жыл бұрын
👍🙏 thank you.
@ronaldomontalbini44313 жыл бұрын
Hello my friend, your explanations about the TS430 are very good, could you guide me how to make the frequency alignment my radio is at 25hz below the frequency. Thanks
@TrakaBat8 жыл бұрын
Nice video Frank
@radioastro756 жыл бұрын
Very interesting video.....
@marcgardner82944 жыл бұрын
I need help with Kenwood ts430s how do I remove the FM board out of the radio I have no signal on display on LSD USB AM
@BeastMasteroo12 жыл бұрын
Connector 10 on this radio I have has 5 wires. No wires cut yet seems to TX on all bands. Why is it 5 wire and not 3? Serial # possibly?
@stevec50007 жыл бұрын
When you connect 12 volts to the antenna connector through a resistor you are feeding current into the radio through the relays but where does that current go? Is something inside the radio heating up?
@nelsnelsen67417 жыл бұрын
The current goes to ground and it is nessary to use a resistor to limet the current so heating does not happen. A larger value resister will let less current thru.
@Dmon741011 жыл бұрын
Berry good
@alessiorroadies8009 жыл бұрын
is the 430 similar to the famous ts 440 sat? or is the 430 superior? thanks for this beautiful video
@sinecioalba600 Жыл бұрын
Hola saludos tengo un ts 430s que corre solo la frecuencia pudiera decirme algo de este defecto gracias 73s an dx de co8aw
@usa2cc27211 жыл бұрын
What jumper number jumper do I cut to show the additional freq digit on the display?
@nelsnelsen67417 жыл бұрын
Don't do it. It is an eratic mod and does not work well.
@didididuh7 жыл бұрын
Look in the owner's manual..it shows it.
@deathtroops3 жыл бұрын
Hello everyone is there anyone knows the cause of ALC and SWR on TS 440 does not work
@kevins47363 жыл бұрын
Clean the relays with deoxit!
@Radioconx10 жыл бұрын
You may already know this but VCO-5 in a TS440 needs to have the Sonybond goop removed from it and apparently this may not affect the 430 but it is worth spreading the info I learned at this link: forums.qrz.com/showthread.php?351511-Kenwood-TS-430-and-TS-440-all-dots-on-display-solution Bob WB6SLC 73!
@Satchmoeddie8 жыл бұрын
+RadioConx They did not use Sony-Bond on all of the 430s so far as I have seen. The earlier ones do not have that goop in them. They sure used it in lots of other consumer electronics back then. TS430s are most famous for cruddy dirty contacts. I don't know about burning the contacts clean though. My Kenwood key entry RF generator was also guilty of this issue. The relays are kind of iffy. It takes a gentle tap to get it to power up right, but once it does she works just fine. Eventually I replaced a few relays & made sure it was spot on & fully aligned it with a calibrated Agilent O scope & freq counter. My FM broadcast band 19KHz stereo modulator was made by Matsushita/Panasonic & no such problems. I do a lot of work on vac tube gear. You won't see my hands or finger smashing things around inside any of those vac tube Xcrvers, Xmitters or Rcvrs. I have fixed enough of this stuff, and finally went and got licensed to transmit last week. Easy tests, except for the extra. I don't think I will be erecting any antenna farms in a national park, but I now know I will need an environmental impact study. These old 430s are nice to work on. I don't even need a microscope.
@yopper1111 жыл бұрын
Hi there, over the pond, I'm from holland (netherlands (19)) I am following it all, its a great help. Ik have a question. Is there a possibility to make the outgoing power, (watts) adjustable? Say from 1-120 watts fm? Because I really miss that. Mine is only giving 55 watts, which is very low. So can I change the wattage (variable) and put it up to 120? Age here is 64 years, an ol'rooster with parkinsons. But still enjoying.. yopper@zeelandnet.nl
@adambrady66756 жыл бұрын
Mine receives poorly. Ready to toss it in dumpster. Poorest investment I ever made.
@felixmartinez6547 жыл бұрын
quality of video is terrible
@felixmartinez6547 жыл бұрын
I have watch this video for 3 times until i make mine works, i critizied the video, but does not mean its not helpful so, thanks.
@TheCasualDrinker8 ай бұрын
it's from a vhs tape lol your lucky you have it at all