Best Mobile Ham Radio 2024 | Best Ham Radio for Vehicle

[@wcsoblake85]

My wife hates the fact I got my HAM license. She hates it because now I have two expensive hobbies. Buying HAM radios and buying guns.

[@HamRadio2]

Haha

[@stahpit1971]

The two things that keep me going. Are we related?

[@mediocreman2]

She only hates it because your third major expense (her) is at risk of losing time, attention, and money.

[@WisconsinGabe]

I say all the time about my gun “hobby” that it’s turning money into noise, I guess we can say same of our radio hobby as well.

[@Hamlocks]

Only 2 hobbies.That’s rookie numbers 😂😂

[@kwhp1507]

20 years ago radios was crazy expensive. When I was a young vol firefighter I couldn’t afford a proper mobile radio so with some guidance I purchased a new ft2800 and modded it myself for 2M tx. I saved so much money and had a good powerful mobile that could get out from any holler in the county and still hit the county repeater clearly.

[@mcconnelljim]

Hey Jason, on the TYT (and other Amazon products)....The "Sold By" is on the right side under "Ships From". That "TYT Store" is a misnomer that isn't always accurate based on Amazon's view of brands. In this case it is Sold By Radioddity and Fulfilled by Amazon. Hope that helps

[@TribbleBot]

My first mobile was an HTX-202 velcroed to the center console of our Ford Festiva. The amp was bolted to the back of the console.

[@JamesKruse]

same. Wish I still had it.

[@Outdoormorefamily]

One of the best mobiles is the 2730. This radio was my first dual band, and still going strong ! There’s a great group for that radio on Facebook.

[@emilioprada7119]

Icom 2730a is my first mobile radio that I just bought at hamcation, I love it!

[@stevearodgers]

I love the FTM-500 as well, but I also run a TYT MD-9600 running OpenGD77. That's a fantastic radio once you flash the firmware.

[@mainetomass99]

FTM-300 is full duplex as well in case anyone wanted to know. I can’t speak for the 500 but I’m willing to bet that it is.

[@romien8wwr414]

Swapped out my FTM-400 in the car for a FTM-500 a little over a month ago. Love it! Good seeing you at HamCation Neighbor, had a blast there. Be safe, Romie N8WWR

[@keeler1160]

N8WWR!!!

[@gorillamotors]

I would love to see Anytone come out with the AT-D578UVIII Plus with HF capabilities (100 watts) like the discontinued Yaesu FT-857D with DMR.

[@HamRadio2]

Yes

[@williamkizer3445]

2730a best all around radio you showed. Love mine

[@mrppassman]

I purchased an FTM-200 at Hamcation. I'm enjoying it, except I miss the memory organization of previous Yaesu Dual-Banders. Paul, WB0BBC

[@KalashmanNC]

Been using the TYT9800 since 2019. I’m still liking it to this day.

[@nc4tn]

Great review, Jason! Although not reviewed, I like the Alinco DR-MD500 for its DMR capability.

[@choppedandscrewedcustoms]

I have the TYT9800 and I really like it I run it on low power and I've been told it sounds good

[@teeshane73]

Gotta like Alinco. I bought my DJ580 ht in '92. It's a tank! Thing still performs and even looks brand new. I've gone through several batteries, of course, and now have a collection of all different sizes thrown in box. My other ht is the Yasu FT-470. Bought it in '91, and yes, it still works and is in excellent condition too. Haven't keyed up in years, now getting the itch to jump on a repeater where I live now. Need to spend some money on a new ht and I'm thinking about a mobile rig too.

[@alexjh47]

I'm really happy with my FTM300 - full duplex + SD card recording makes it great for satellite work

[@FooBar89]

no CAT

[@michaelcampbell1128]

hi Jason, had my TYT 9800 in the truck for 2 years and still works fine.

[@chrispy6313]

I got a 2730a for the mobile, I liked it so much I bought a second one for the garage base. I love the detachable faceplate with mike attachment, only one cable to faceplate. I recently installed the Icom Bluetooth board & and paired a trucker headset with microphone, BAM! Hands free!

[@devonsaquariums2703]

Same here. I have 2 as well. Should also mention that it has cross band repeat capability. The only thing that's a bummer is if you want to mount the face plate to the radio, you have to buy an additional bracket and shorter cable, which, for what you get, is quite expensive.

[@jockmazza]

Nice one. Bluetoothed an old realistic dx394 during lockdown. Id not done radio since 94. Thanks

[@jneale5204]

I don't understand all the popularity with the FTM-500. Every time I saw something new on it, including the promotional videos, I would want it less. Plus it has the Yaesu menu setup. I own the FTM-400 but I am not getting a 500. I also own a Icom ID-5100 and love it. That is my favorite overall VHF/UHF mobile radio.

[@mitstax]

I purchased a tyt 9800 as my 1st mobile radio. It burnt out within 6 months. I attempted 3 X's to contact tyt for repair or replacement with zero response. I now use anytone dual and triband mobile radios. Same price and higher quality

[@moondog_radio]

The Yaesu mobiles don't have memory banks. This is a deal breaker for some. On the FTM-500 there is no effective way to scan two different sets of memories (like one set on the A band and the other set on the B band). The radio is also missing a feature that is standard on many other radios where after a signal drops, you can pause for a variable length of time before resuming a scan. Yaesu's cheapest handhelds have both of these features. Yet they have left them out on their mobile lineup. This is why my two FTM-500s are sitting in their boxes... and I'm using my ICOM radios instead.

[@HamRadio2]

Can't say that it makes that much difference to me

[@moondog_radio]

@@HamRadio2 yep. I would expect that is true for most. I do a lot of scanning of very busy systems. It's super frustrating to have the scan resume immediately after someone unkeys. You never get to hear the other person's response. At least that is my use case. All other radios I own have this feature (to pause before resuming)... except the Yaesu mobiles. Same thing is true of memory banks.

[@betterl8thannvr]

I've had 2 TYT TH-9800s and the finals on both went out after a couple of years. My FT-8900 meanwhile is still going string. So is my ICOM 2720 which is using the same antenna as the TYTs did.

[@billyjoejimbob75]

My buddy had 3 TYT 9800 radios. They all blew up in a short time. He has 1 wouxun 980 that outlasted them all. Usually audio problems. TX audio goes out, RX audio goes out. One sided radio. I like the retro look of that icom.

[@HamRadio2]

I still have my original TH9800 but I am aware of some of them having issues

[@3TQVK]

Jason, I bougth the FTM 400 just before the dicontinuation I didn't like the 500 much Awesome APRS on the 400 Pete VK3TQ

[@CyborgAlienBariaur]

Part 90 includes a lot of emergency services frequencies.

[@ryangillespie1726]

I am starting to love my ftm 500 especially since I got it for $500 with the last gigaparts rebate. I will say the menu system is clunky compared to the ftm400. It replaced my 400 for mobile use but the 400 will be used as a base station now.

[@joshuamidkiff7990]

I just found this out the hard way but the AT-578uv III plus is not part 90 certified. The previous pro version is and thus the plus model does not have the professional mode. My solution was to buy both and use the plus as a home base station 🤣

[@AndyAAzeroAM]

Good job on these type of videos, tons of great info. Thanks (Really like my Alinco 735)

[@randyschoumaker3814]

I'm getting my feet wet on the FTM-500. Loving the radio. Can't wait to actually transmit on it.

[@SimiNelsonFamily]

You have a lot of good picks in your line-up. I have the Yaesu FTM-300 and the FTM-400. It looks like they discontinued the 400, which is unfortunate as it’s much more intuitive to use with its touch screen. I also have the Anytone 578, but I wish they made it with a removable head.

[@jimcaddis9417]

Saw the FTM500 on Tuesday at our club, the screen is small only .4 of an inch larger than the 300. That VFO that looks huge in the pictures is also small. Not impressed, the 400 is a better option.

[@HamRadio2]

The 400 is no longer in production though.

[@SIGINT007]

Not to mention the public face of these radios is an arrogant turn-off. I watched a couple of his videos recently and quickly decided Yaesu doesn’t need my money while he’s their spokesperson.

[@MrTmorton77]

Was hoping to hear about he FTM-500 @ 14:20 you mention you were going to talk about it but I never heard another word. Thanks for the content.

[@HamRadio2]

I have 2 long videos specifically about that radio

[@jimedwards9310]

Love my 5100. And ftm400. 😁

[@berzerkerseamus2955]

I run the AnyTone AT-778UV and I think the IC-705 should be considered for the higher end

[@kb7pab]

The 2730a is a really nice Radio but the Cost goes back up if you want the bracket to attach the face and the other braket to mount the Radio

[@HamRadio2]

True

[@sailormike1089]

I have the FTM-6000 as a base radio but my mobile is the ANYSECU WEP-9900 with a color screen on the mic. Doesn't have all the bells and whistles but it does the job for me.

[@ScottyD]

The AT-5888UV III can receive in AM mode 108~180MHz

[@ChristiannTyler]

Hopefully, someone here can assist me. Upon learning about the GPS features of the Icom 5100A, I became interested in obtaining a radio with similar capabilities. As I frequently travel around the country and will soon embark on a coast-to-coast journey, having GPS functionality is crucial. While I am newly licensed and have relied on a CB radio during past trips, I now feel the need for a more sophisticated radio than just a UV5R. Is the Icom 5100A the only radio in that price range with GPS that can locate nearby repeaters?

[@wowsly]

the tyt 9800 is a great radio. had mine years and i get the same reports when i am in my landrover :D i have to pull over for a qso lol

[@alexblack6762]

TYT TH-9800 has a design flaw with audio processing IC. Due to over-voltage (by design) that IC has short time to live. That's why people return it. Otherwise it would be excellent radio.

[@julianvega2654]

There is a mod to add a fan to keep it cool.. the other solution is to run it at Med power. But who wants to do that? Lol

[@ag1382]

Yaesu has had it their way over the last year. Wonder what ICOM and Kenwood may have coming?

[@DominicMazoch]

One thing missing from your review. Does the rig have a data port for Packet and WinLink.

[@HamRadio2]

Almost none of them do

[@johnarcher9480]

Thats what the digirig mobile is for 😉

[@rocketman221projects]

​@@johnarcher9480 No data port means no high speed modes. You are limited to the bandwidth you can get through the mic port.

[@cbman4767]

Ham radio can be free if you know what you are doing. Most ham clubs have a swap system. I gave away a Yeasu FT 101 to a new ham. It can be free if you get you crap together and talk to people on the air.

[@calvincollier8]

What about the kenwood 710g ? It does many of the features you talked about. The transmission of the kenwood is very crisp and clean.

[@HamRadio2]

It's no longer in production

[@calvincollier8]

@@HamRadio2 you’re right, I forgot they were getting out….. too bad , it’s a good radio

[@edjahman]

What do you recommend for a cross country trucker trying to get in on ham? Thanks

[@FierceProtocol]

FTM 400 Take out one resistor and you have a GMRS and MURS radio as well with the 400.

[@romien8wwr414]

That resistor is one of the smallest ones I've ever "eliminated." I literally had to go out and buy a magnifying glass, then in order to cut it I heated up an X-Acto knife blade with a flat tipped sodering iron, then used the hot blade to cut that bad boy. Wow was that little......

[@HamRadio2]

That's true on most radios

[@wescourtney1510]

My TYT 9800, or, was it 9500?.. I used for less than a year. It is just a police scanner now. It got so there was almost NO audio in the TX signal. And of course, no one fixes them.. ... Same thing happened with my WouxunKG-U950P. It too is just a scanner now.

[@jackrodosta7971]

Just passed my Tech license looking to get the Yaesu FTM500 for my truck, I run a pilot car service and I'm all over Texas. What is the best antenna to pair with this radio on my truck?

[@barryinn1778]

I have the Yaesu FTM500 and like it . I also have the Alinco 735T and don't like it because it is hard to program from the radio. Alinco's Manuel is confusing to program radio, some features do not work even following their directions. Alinco 735T receiving audio is not clear kinda distorted on repeaters.

[@KrytteR420]

I now own that very yaesu 200, great little radio!

[@HamRadio2]

Very nice!

[@CyborgAlienBariaur]

I'm more interested in the TYT MD-9600... I really want the Anytone 578 UV III + the most, it's what I'm saving pennies for...

[@cocopuff239]

How come no Xeigu G90? Feel that radio should be on this list.

[@newYorkStories]

Just got th e FTM-500. Love it! Do you also have a video about mobile HF radios?

[@HamRadio2]

Not yet

[@andrewyoung-n8ary]

It’s not the radio that’s the problem for the FCC. It’s the uninformed operator who buys a radio and sets it up wrong. The type accepted radios have the rules built in.

[@ItsEverythingElse]

I don't think the FTM-500s screen is larger. Correct me if I'm wrong.

[@HamRadio2]

Larger than the 300, yes it is

[@Toner-N1SWT]

I like the Yaesu FT 2980R. 80 watt transmit gets you out there on Simplex. Simplex transmission is what your going to need when the Shit hits the fan. $215.95 for a quality radio

[@BR20276]

Love your video's! So I am not knocking your videos just frustrated with these manufacturers. I have to say though APRS right now is just not my thing. I don't travel enough to justify the expense of an APRS capable radio. There are three different Digital modes out there. Fusion, D-Star and DMR. Crazy that these manufacturers can't get it together and be on the same page when it comes to the digital voice mode. Icom's near repeater function for those who travel a lot is a really fantastic feature though! It would be nice to buy one radio and they all shared the same digital mode. I know, dream on and I am beating a dead horse! I have had the Yaesu 400, ft 3D and ft 70. Sold them all. Not really into the VOIP thing and the few digital repeaters in the area are not used heavily other than for a few nets and some owners put restrictions on them. So for now I'll just stick with analog. I use the Alinco DR-735 as a base and I am very pleased with the RX audio and TX audio reports are great. What little bit of driving around I do I just use an HT with an external mobile antenna. The Alinco 735 is a simple radio to operate. But then I am a simple person! Hi, hi! We all have our preferences.

[@Shrek0gre84]

So out of curiosity what's a great mobile radio I can use since I'm a truck driver. I don't like regular CBs

[@HamRadio2]

VHF? Or HF?

[@robertmeyer4744]

nice video. the first 4 band in video I have in a box. have not used it in years . is a great radio but hard to program. it was your video that got it done for me. the only thing I do not like is FM only. and no 222 Mhz. i like the 4 bands but would rather have 222 instead of 10 meters. I did program to open up RX . will receive CB but FM only . it is my back up radio now. I would like to see a 4 band all mode model in VHF/UHF . give 220 band . may be 900 MHz but SSB/AM/FM RTTY . 1.25 meter SSB can go very far . 2 meters and 70 CM does as well . may the FCC give us 4 meters. the UK has that but no 220 . 73's

[@chrissewell1608]

Digital would be nice to have in a mobile, and APRS!

[@HamRadio2]

Yes

[@hanswulff4910]

I returned the TYT 7800 which has the same screen, ifound the screens menu hard to read the led. could not tell what the letters were and could not program the radio with there software as it would stop part of the way, no help from the company ended up with the Anytone 778.

[@CriticalThinker-42]

You have much more experience with various V/UHF radios than I do, BUT I Think its a shame that you overlooked 10 meter SSB mobile radios for Tech's. (possibly another video I missed?). 10 meters SSB is a great introduction to the joys and longer range capabilities of HF, like legally talking all over the world from Mobile (POTA or Home) with an under $300 rig (new), like the QT-60. They don't have all the bells and whistles of an Icom IC-7300 or Yaesu FT-710, but you really don't Need all the bells and whistles to talk all over the world and have a completely different experience than with V/UHF FM. To me, V/UHF FM are great workhorse's, but 10 meter SSB is for Fun! Might as well enjoy Cycle 25 while its here! 73 mike N4ONL

[@HamRadio2]

The QT-60 radio is junk. Realistically, most of those "10M only" radios aren't worth the money you pay for them. The front ends aren't good, the audio is poor and they have spurious emissions. This is why I don't recommend them

[@CriticalThinker-42]

@HamRadio2 Many people would disagree with you about the QT-60, including Josh - HRCC (Ham Radio Crash Course) who is Not known for recommending radios that emit spurious emissions. ( SEE HRCC Episode: "Ham Radio Technicians! Get On Ten Meter Parks On The Air! (Radioddity QT60)" ) Case In Point: Josh also recommends the Baofeng GT-5R because it meets the FCC’s spurious emissions standards that other Baofengs don’t. Typically if the audio quality is mentioned for QT-60 reviews, its reported to be very good, both in TX and RX (Josh, HRCC,...), and it has good Digital Noise reduction. Plus the QT-60 can be unlocked to also do 12 meters for when Tech's upgrade, therefore its Not in Your stated class of ""10M only" radios". Yes, as Licensed Ham's we can modify or build and use Any radio as long as we don't radiate spurious emissions above the FCC's limits. But spurious emissions, if present, can be reduced to below the FCC’s standards with inexpensive external filtering, such as a HF TVI (TV Interference) Filter, or Band Pass, or Low Pass filters. Also the QT-60 appears to be built on Fiberglass rather than cheap Phenolic PCB’s (Printed Circuit Boards) showing a dedication to quality construction. Do you also have problems with old timers using Out Dated tube type AM equipment that’s Not up to todays level of bells and whistles, like Steve N4LQ and their multiple AM nets? Many Ham’s consider DX-60’s… to be “Junk” also, do You? If your going to call a rig “Junk” shouldn’t you also quantify Your definition of “Junk”? Bottom line, to each their own. We shouldn’t dissuade other based upon our prejudices, lest we be labeled “Sad Hams”. 73 mike N4ONL

[@JPDW3072]

No repair shop in the Netherland wants to repair Chinese radio' s, reason not given.

[@HamRadio2]

Repair costs are probably more than the radio is worth

[@gregpearson7013]

Does the 500DR come programmed so a technician cannot use the disallowed frequencies?

[@HamRadio2]

There's no frequencies that this radio will do in the ham bands that a technician cannot use

[@marinedad1775]

RX GOES OUT ON THE 7800 AND 9800

[@mrppassman]

How is the quality of the programming software for Alinco?

[@daylus4358]

Another excellent video! Question, I have had a Yaesu FTM-400 for some time now and love it to pieces. How would you compare / contrast that with the newer 500?

[@HamRadio2]

I never had a 400 due to all the problems with the first run of that radio. Those issues were all resolved with the XDR models but I never bought one. Most people think that the 400 is better for APRS stuff overall.

[@daylus4358]

@@HamRadio2 Great point! Mine is an FTM-400XD to be specific. Just ran out to the jeep to be certain.

[@HelloNotMe9999]

Does the ICOM 2380A receive Air Band (108-136 MHz)?

[@JoeFramo-uw9fp]

Jason great video ❤

[@HamRadio2]

Thanks

[@stahpit1971]

Lots of nice radios on that list how is one to choose ?

[@HamRadio2]

Buy the most expensive radio that you can afford, whatever that number is

[@Wolfpacker]

What does it mean by FM only on the wouxun kg-uv980P? Im about to take my test and just doing some research. I know the 6 and 10M portuon are for general as well. But ive heard this 'FM only' phrase elswhere.

[@HamRadio2]

FM is a mode. You will learn about modes in the test questions. 6-meters is a band that Techs can use, but 10M FM portion is only for General and higher.

[@RandomStranger69]

Id like a Yaesu version of the Icom IC705

[@s8ultra732]

Hi, are you still using the icom 5100? Im planning to buy it too. Torn between 2730 and 5100.

[@HamRadio2]

Yep, had it in the truck for a few years now

[@s8ultra732]

@@HamRadio2 thanks will get one

[@andylondon99]

Is there a radio 📻 that can go from SF to Chicago?

[@HamRadio2]

Sure, HF

[@CharlesFockaert]

thanks for the vids. heard nothing said about programming the radios? Chirp or separate - expensive, like the RT Systems WCS-2730 Programming Software for the Icom 2730a at $48? if not mentioned, means manual programming?

[@HamRadio2]

Programming software wasn't the focus of this video, but... Most every radio has some software of some sort. RT Systems is expensive, yes. I don't use it. CHIRP is great, but only covers some more popular models. I'm not sure what Icom software you are referring to for $48 though. Yaesu has free software for their radios.

[@CharlesFockaert]

@@HamRadio2 I find your vids very useful and informative. some of the best online in fact. thank you. RT Systems WCS-2730 Programming Software USB Kit with Version 4* Software and USB Cable $47.99 But as newbie, I need to know which if any software comes with or is needed for the model. also, 12volt DC or 120v AC? both? will the unit work off a 1000 watt inverter? 1500 watt inverter? I'm leaning towards the ICOM 2730A despite the addon expenses. what antenna should I use? Jpole or ??? I'm in a Mobile Cabin. (motor home to you fellows). how about "Here's the moblie unit I would buy today for my first entry/first purchase, I would use this antenna and this software, and here's what I look for?" and why. You need this cable, these connections, etc. available here. A complet bundle I guess. Heck, I'm the newbie. and not so proud to admit it. don't want to buy some "stuff" that doesn't work, that will be returned and lotsa stuff to know and KISS doesn't seem to work in this "hobby," but Murphy sure does. lol hard to find a true live personal Elmer these days willing to do just that. you guys are as close as some of us get to an "Elmer." KI7IJS

[@ragheadand420roll]

Plus version is $225 on amazon

[@Superbadmike]

Yeasu 6000r ?

[@ac7fd]

A video named “best mobile ham radio” and not a single radio with proper HF coverage? I get what you’re doing but miss the FT-891 and especially the IC-7100 which is the only shack in a box for mobile usage. Seeing all those Chinese brand radios recommended always leaves a bad taste to me. Not because they are Chinese, some Yaesu are made there, too and good Products come from China (get what you pay for applies there too). Because most of them are significantly worse compared to the Japanese competition when it comes to the really important specs, the RX/TX performance. I sold my Anytone because if it’s horrible receiver compared to an Icom or Yaesu in more challenging environments. Thanks for the video.

[@HamRadio2]

I have another video for HF mobile

[@iffykidmn8170]

which is the best one for an unlicensed operator and how many fars will it get.

[@HamRadio2]

Anything that has "GMRS" stamped on it

[@iffykidmn8170]

@@HamRadio2

[@iffykidmn8170]

@@HamRadio2 Hmmm thought those required a license as well. oh well catch me if you can.

[@TonyLing]

We want to see more multi mode UHF/VHF mobiles on the market

[@HamRadio2]

YES

[@TonyLing]

And stuff the digital modes if they can't manage more than one of them at the same time @@HamRadio2

[@Chris-hy6jy]

Or get the Yaesu with an even bigger screen, the FTM-400! 🙂

[@HamRadio2]

No longer in production

[@Chris-hy6jy]

@@HamRadio2 oh I know. I was lucky to get a brand new one about 6 months ago. Plenty on the second hand market though. It's a shame Yaesu downgraded the screen on the 500.

[@Johnyrocket70]

There's a KZbin channel in California. He has a way to go from d star to fusion

[@HamRadio2]

There are a few ways to do that

[@FooBar89]

out of these radios, only the Icom radios have CAT, that’s pathetic Yaesu yes, the 2730 has a CAT interface!

[@stahpit1971]

The 500 doesn't have it?

[@FooBar89]

@@stahpit1971 nope, Yaesu does not make any VHF radios with CAT

[@stahpit1971]

@@FooBar89 Makes you wonder whats going on at Yaesu. when they killed the 400 and put the obnoxious head 500 out I was done.

[@johnregan3075]

73 John N1JLK

[@bebophawk]

how about the Yaesu 891

[@HamRadio2]

Not VHF/ UHF

[@christophersmith1155]

TYT 9800 . AWSOME

[@JoeFramo-uw9fp]

Yeasu M500

[@MarkChapman-v8z]

Will icon 2730 do gmrs

[@HamRadio2]

No

[@bassmanjr100]

10m should be open to Tech IMHO.

[@HamRadio2]

10M SSB is

[@rocketman221projects]

Techs can't use FM on 10m and the quad band radios don't support SSB.

[@theoriginalcrb]

Best 6 meter mobile? Weather spotters here are on 6 meter.

[@HamRadio2]

Weather spotters around here are on 2M. There aren't many 6M only radios

[@dudleybrown7030]

Do any of these mobile radios also work on GMRS? Yeah, yeah, I don't really care what the bureaucrats say at the FCC.

[@HamRadio2]

You can mod them to do GMRS, yes.

[@dudleybrown7030]

@@HamRadio2how? Anyone able to link me? I'm no electronics engineer so I don't plan on removing a flux capacitor myself. 😊

[@HamRadio2]

Search KZbin. I've never done it but if you studied for your Ham license, you'd have some training on how to do it

[@dudleybrown7030]

@@HamRadio2 Do you know anyone who took their ham radio license recently who didn't just game the exam (i.e. memorize the correct answer)?? Not me. Jason, you should have a care package in your mail today.

[@wushock92]

Great overview, Jason. WØRHP

[@SmileyFtW]

The reason it gets returned is because TYT quality control is terrible - you might get a good one or you might not. And if you are outside of Amazon's return window when it dies you will be stuck with a brick. Mine died before 6 months - outside the Amazon window but well within the manufacturer's window. I could not get a repair or replacement. I have two other TYT radios (8600 and 7800) that have not failed (yet - crossing fingers). I am not inclined to spend any more money on TYT radios.

[@GVSolo]

I wonder why the Yasu Ft-891 did not make the list.

[@adamny5e591]

The first radio rated: “not sure if it works for Apple/IOS, …..I didn’t research that”. “I used it a few times …..and couldn’t get it to work just right, but that wasn’t the radio’s fault”. And this radio makes your “BEST OF” list? Sponsorship has gotten to you man. BEST OF should be 3, maybe 4 radios, NOT the eleven you have to name to keep your sponsors happy. Sad

[@adamny5e591]

The second radio “….you have, say a 75% chance of getting a good one” 😂 hack

[@SoDogtravels]

Sorry tmv71a is still the best

[@HamRadio2]

No longer in production

[@shoa2285]

Maybe it's because no one wants to have a radio with the same name as the The Young Turks TYT liberal progressive KZbin channel. 😅

[@HamRadio2]

LOL, I have thought about that...

[@crashmaster26]

Oh ... you're giving people VERY bad info.... guess I'll be un-subbing. NO ONE should be making a faceless radio that requires you to give up access to all the data on your phone. to use. I came here to see the best and you're showing me the worst to start with that NO ONE EVER SHOULD BUY !!!!!!!!!!!

[@HamRadio2]

None of the radios here fit what you're describing so maybe you're commenting on the wrong video

[@BryanDaniel42]

ICOM 2730A was my first mobile radio and I regret selling it.

[@davep6977]

Great radio. I caught them on sale for $250. My YL is a ham. I bought 3. I programed All the same. My truck, her SUV and the base. You can run dual mics. One plugged into the head and one into the rf unit. I have a desk mic and a hand mic depending on my mood or if I'm on a net. Great video I'm all ICOM.756proIII,2730A, 9700 & a T-90a 2m,70cm, 6m hand held. W9DLP 73