Hantek CC-65 Current Clamp - Part 2 - Teardown

[@scottmarshall6766]

Thanks for saving me from taking mine apart. Seems well made inside and out. I'm very happy with mine, it performs well above it's price point. I wish there was a sheet on calibration procedure available, it looks as though there's a bit to it.

[@jwrtiger]

Overall two nice videos on the device. It would of been also nice to show it in operation with a comment on accuracy. Again thanks for the video, I just got one.

[@alocin110]

Excellent presentation on the subject and well detailed. I liked your video. keep up the good and helpful sharing. Regards.

[@jstro-hobbytech]

great video.

[@ghosthk]

I got it directly from china factory, it just cost USD$40. It maybe the cheapest current clamp but it does help.

[@CHIBA280CRV]

Very informative video sir thank you..I have a snap on low amp clamp and it doesn’t work . Do you know where I can send it to and have it repaired ? Maybe I can send it to you and you can repair it in a video and I can pay you for the repair ? Just a thought .

[@ats89117]

I just discovered and subscribed to your channel. Nice videos on the Hantek CC-65 but it would have been nice to actually do some measurements and look at some signals on a scope...

[@AqibKhan-xf8vo]

@NFM If i want to measure 3 phase power, then do you think it can give me exact values of power? do you think power measurement from one phase will be different compare to 3 phase?

[@louis-philippedrolet196]

@NFM What is the hall effect ic? Does it limit the banwidth?

[@ByeTech]

why not add enamel after testing each trim pot resistance

[@madkev415]

Is the amp reading out of this unit as actuate as compare to fluke clamp? Thanks

[@Tirdad1981]

I wonder how it can measure AC current without a CT and just by two hall effect sensors?! I wish I could see the schematics of this clamp.

[@dtrrtd774]

Can the BNC connector be converted to banana plugs for the use with a DMM?

[@ghosthk]

DTR RTD Yes It can, I am using

[@saibabu2651]

whats the chance bring inside any chance to battery revorce polaraty

[@saibabu2651]

hai say for one part unknow part linear voltage regulator in my AMP clamp metar that regulator is buring Idont know how its going plz you can explan to any batttery revorce polarity its can hapn plz given information

[@TECH_GEEK10]

I prefer your old mic setup

[@NearFarMedia]

+Stephen Germiller thanks for the feedback. It's actually the same mic setup, but in a different environment. I'll tweak the settings and see how that goes in the next video. Cheers!

[@AqibKhan-xf8vo]

Can I use this to measure 3 phase machine tools power?

[@NearFarMedia]

You can use it on one phase at a time with no problems.

[@tejonBiker]

if you want to do in the seroius way there is something called power quality equipment, this equipment can measure the three phases current at the same time (and a lot of other things)

[@malekservicespecialisten3906]

Hello guys.I have bought from Ebay the same amper clamps,i have a problem to return it.But this was a problem: After installing the battery, i feel the smell like ''burned electronic device''.Device do not react,like no battery power. Did anybody have a idea what it can be? By the way,excellent video :)

[@SouthernHerdsman]

Way expensive they're selling at $70. Costs 32 yuan ($6.4) to produce each.

[@jstro-hobbytech]

great video. I don't trust anything hantek as someone who has owned their gear in the past. but, I am a hobbyist and not an expert and am open to any info.

[@AqibKhan-xf8vo]

@NFM

[@Graham_Wideman]

Teardown of similar PDI CA60 here: kzbin.info/www/bejne/rqacaX-rqdOFrc0

[@ausmartin1]

I'm sure Hantek NEVER use their own products ... in 2021 the Zero button on ONLY the CC65 gets stuck down... Ie it travels too far down. Now why they can make a zero button work on the CC650 and not on the CC65? Use dielectric grease to resemble with luck those silly spring dual switch. Fixed the problem by putting an o ring to limit travel... Hantek 🤯🤡🤯 like the1008C automotive oscilloscope that fail near HV noise due to non sheilded usb cable...lol!