Harbor Freight Motorcyle/Utility Air Lift! (pt. 2)

[@conservativechristian8508]

Clearly the best set-up I have seen. I have three of these tables. Excellent explanation of what you did Sir.

[@crownline196]

Conservative Christian , thank you, it was my first attempt on the conversion, I just took my time and planned it out. A lot of it was trial and error but in the end it works great. I’ve had no trouble with it so far

[@jstalcup1989]

Nice simple build. I've watched many videos on this and they're always more complicated than they need to be

[@scottgreen9367]

By far one of the most simple designs for the conversion. Well done sir

[@mikefink6228]

I've viewed several of these air conversions. Your setup is the simplest and cleanest I've seen. Good job!

[@eminor7536]

I just picked up my lift and plan on doing the conversion, your video looks to be the simplest cleanest method to follow. I think I’ll use you video as a guideline. Well done man.

[@robertmcmahon2744]

Great video. I've asked the Harbor Freight people at the store if I could use that very pump to modify thier table. Nobody had answers. I figured there was a way ,but I'm not an engineer. Thanks for the info.

[@travisfranks2826]

Really enjoyed this I have been watching a ton of these ,so I know what I want to do and I'd agree this is one of the best ones out there I liked and subscribed want to see more of your work Thanks EZ$

[@petedetects7012]

Great idea . I saw your first related video and thought the same thing using an air jack. I'm glad you did it , now I know it works. Thanks for sharing

[@dannyabbatiello4456]

Love the idea on the winch. I was thinking on an electric one, but had concerns on where mounting it would come to play. Hope you do a video on the winch as well.

[@crownline196]

danny abbatiello , thank you, the winch system is only really there to help load or unload the table, I installed it for the purpose of moving heavy items( ie. riding lawn mowers, snowblowers and such), although I’m sure at some point I’ll need it to load a motorcycle.

[@dannyabbatiello4456]

Is the winch also a harbor freight item ? I am in my sixties and find it easier to ride my bikes on my lift as well but have toyed with the idea of using a winch my self for safety sake . Will you be making a video of how you mounted the winch ? @@crownline196

[@jimmyphillips2216]

Thanks for sharing, seen a few but like yours best.

[@MartyLacy-ds3wi]

Just bought one yesterday, nice air assist.

[@billhorn6840]

Love to see a drawing of the jack on the plate and the bar it’s welded to

[@MartyLacy-ds3wi]

I just bought one yesterday, was looking for a air assist. You did a good job on it. Tks

[@TheManFrayBentos]

Excellent. Mine is almost identical to the HF lift, and that's a very informative how-to. Thanks. Great vid, straight, to the point, no farfing around.

[@cjlowflyer9885]

Brilliantly executed. An exquisite upgrade.

[@dennisjoiner3717]

Nicely done, and thanks for sharing with us.

[@mikedodge1042]

Awesome job! I was going to spend way to much on a lift until I saw your video. Thanks again. Mike

[@greekos573]

Terrific job, well thought out and executed! Thanks for sharing, planning on doing one of these in the near future.

[@calyfornykid]

Great job looks like it was made that way by Freight, or better. I own one also I been thinking about making it an air lift. Before I attempted doing so this video sure will direct me in the right direction. This lesson gives me more confidence that I need.

[@lucky15driver]

I really like the mod you did to that table. I didn't know that a standard air hose fits that jack. Great video sir!

[@charlesbradshaw8673]

Great upgrade, will be checking into which lift I bought just before I left for work, but I did notice that you need to do something about the removable plate, it doesn't care to much for the weight on it. A few of my friends have told me to strengthen the plate almost right off. Again great job on the front carrier and the airlift.

[@crownline196]

Charles Bradshaw thank you

[@kakarote2277]

Excellent video. Gave me ideas how to prepare my lift when i get one . As i too have an ultra classic.

[@curtispomykal8432]

Great job bud! I have a 1600 Nomad. This will work GREAT. Thank you for Sharing.

[@xdestin4674]

Awesome job ! Nice bike. Have a great day.

[@benjones4658]

Super clean like the videos. Awesome your son helps out 👍

[@stefinatrix3426]

This is by far the cleanest implementation of this mod I have seen so far, thanks for sharing it. . After some checking, there are a couple of different versions of this Harbor Freight lift being sold. This model is #69904 and the other one being sold is #68892. The mechanisms and bottle jacks used by the two versions are completely different and while it is still possible to modify the #68892 lift, it requires a lot more work/fabrication. If you want to do this mod with the least amount of headache, get the #69904 lift. Also, the current version of the 12 ton air/hydraulic jack (#94487) has relocated the air inlet to the top of the air motor housing and is on a swivel so there are no more ground clearance/hose routing issues.

[@MF-yw7vl]

Well I was just scrolling these jacks with the airbag cuz I got one of the harbor freight Jack but that is a great idea I just don't know where to begin but I save your video and I'm going to give it a shot that is so cool said the hell of a lot of money 🙏🤗🦾🧰👨‍🔧😎👍

[@bigdaddysshop8180]

Great job. I've been looking at these.

[@FABAutomotiveDetailing]

Being that the base is cast iron how did you weld it to the metal pipe? I know cast iron can’t be welded with a normal MIG welder

[@retiredarmyvet2018]

Five years later I would love to know how this set up is working.

[@alanstrange7077]

The air jack base is cast. The weld may fracture and fail due to vibration over time. Just a word of caution.

[@travisgray3331]

Great video and conversion plan...the best on the subject. quick question...were your welds 3 on each side for a total of 6?

[@tommeng4960]

I just picked up a lift with a leaking pump. My plan is to modify mine the same as you did. I bought the 12 ton jack yesterday. When you have the lift all the way down is there any wiggle room from the base of the pump to end of the adjustable end of the pump. My pump looks like cast iron so I wouldn't want to weld to it. I was thinking maybe a 1/4" flat steel plate and weld a 3/4" black iron pipe to that. I'm not sure if I'd have enough room to add the plate. I haven't cut the mounting ears off yet. That's why I'm asking about the clearance.

[@wrgumaer]

Do you still use the manual locks to hold lift up very nice job on the table and great information about what you did to convert over

[@douglasebrandeljr4754]

I liked it it looks better then some others nice work

[@crownline196]

Dougs thanks!!

[@gbleisch]

I know because I've had to go through this...................One should realize that H/F sells this table in 2 versions. This modification only applies to the lift having the rectangle tube cross member and the jack having the 2 ears on the bottom. You'll need to go a different route for the other table. H/F part number 69904 is the model in this video, H/F part number 68892 has the jack mounted totally different. You'll have to download both user manuals from H/F and even though the page one photos are the same on both manuals, go to the parts diagram page to see the difference between the two tables. Hope this helps you before you buy the wrong table for this modification.

[@jackprice3108]

Gary Bleisch I appreciate the response,

[@eb1941]

I have the 68892 model. Has worked well for me. I think the same concept can be used by placing the new jack in a different position. On the 68892 model, the cross member that holds the jack can be removed and a new cross member with the new jack can be put in its place. I might try this in the future, but for now I do not use the lift to often, so a take a few pumps. Thanks for posting this video, nice work on the mods.

[@Mrinspiredby]

Great job! What are you using to activate the jack? And dose Harbor Freight have them?

[@elvinrinoa2027]

Wow thank u I have the same lift 4 my bike 🏍 good idea 💡 the air compressor that u have under the table is that a regular outlet

[@tripplecrossproductions7544]

Elvin R Inoa yes, it’s plugged straight into the garage outlet

[@elvinrinoa2027]

TrippleCross Productions ok 👌 thanks 🙏🏻

[@am3121]

Great job. Why do you only have one strap device bolted on the right side?

[@Running-with-skizers]

Great idea and great taste in bike I have an Electra standard same year and color as yours🤘

[@crownline196]

bastard with a beard , thanks buddy👍🏻

[@michaelmessner3169]

Do you feel is could pick up a side by side? About 1500 pounds? Thoughts on the strength of the table itself. Thank you and well done.

[@TheGreatestBeyonder]

Great job! 👍🏻 next would you mind doing an electric conversion? 👍🏻👍🏻

[@norcal8718]

What was making the noise, was it your compressor or the jack on the lift? If the compressor is full of air the lift should rise up with no sound right.

[@garyjohnson3108]

I'm doing the same setup this sunday same lift and same air bottle jack just bought it today..I have a Harley Road glide though about same weight.. One thing I noticed is the wobble when you first start to lift, Mine does the same thing its kinda like maybe they didn't get everything lined up perfectly on the lift when they built it as these are welded by people or robots i dont know.. But it shouldn't do that. My friend owns a harley repair shop and his $2,800.00 lift does do that with my harley on it, but my harbor freight does.. I'm probably gonna do the same mods as you but i'm going to make the table itself more rigid stronger to see if that helps...Got welder will weld :) Just wondering your opinion on the wobble..

[@dlos1987]

I wanted to see how you would remove the rear plate. For changing a tire

[@RestoreItAll]

I use and purchased from Amazon Orionmotor tech A scissor lift Jack While the bike is secured and trapped to the front

[@eb1941]

Great work. Has anyone done a conversion on the HF 68892 lift? Interested in options to convert that model.

[@bikemancody2752]

Great jobs guys.

[@jaseysmith1629]

Nice build! The only thing I would suggest is to get rid of that tire chalk and get a tire vice. I’m a Harley Davidson Tech and if you ever had to remove your front tire you are going to be stuck. That chalk is best used for trailer transportation of a bike.

[@spyder66us]

the chalk is perfect if your putting bikes on a lift by yourself alot, tire vise is useless for that. If I need to remove a front tire I just use a frame lift.

[@alanstrange7077]

If I work on the front end I use my overhead gantery crane to lift the bike or a frame lift.

[@joshrichards4095]

you did a great job

[@crownline196]

Josh Richards thanks, I appreciate it

[@daveblacken9819]

Great job. Whats the loud clicking sound when going up

[@crownline196]

Dave Blacken, it’s the air motor operating the pump.

[@jdanderson1227]

Did you weld the 3/4 inch pipe to the frame or is it loose to move with the jack?

[@EdGW997]

Great video! What did you put under the lift on floor?

[@tedmurray5245]

Great video, , how did you prevent heat damage to jack when welding?

[@RTAMechanic]

That is really informative thank for sharing.

[@ruinneder97]

@tripplecross..first I want to tell you that you did a great job with this modification. But I have to ask you, why not leave the ears on the square crossmember, and only use a short piece of pipe and rod, long enough to get across the ears mentioned above. Using that as your pivot point, rather than going completely across from C channel to C channel? One more question. Did you have to drill holes through the C channel frames for the 1/2”rod/3/4” pipe or were they existing? Thanks

[@spiritofthehighway9100]

Very informative and helpful. I bought the same lift. Have not done the conversion yet. I have a Roadglide. When I attempt to roll bike on lift, the table slides forward even after I screw the castors down to touch the floor. Is the rubber mat the key piece to stopping this table from sliding forward when loading bike?

[@crownline196]

CMA Spirit of the HIGH WAY , yes, the mat will definitely help keep the table in place while loading👍🏻

[@RestoreItAll]

My lift is a couple of feet from the wall. I just place two 2x4 s up right on the floor at the front of the lift . Does the job for me and remove them when the bike up

[@ruinneder97]

You can also drill a hole in the bottom frame C channel, and put a wooden spacer block 1-1/8” thick between the frame and your floor. A couple of 1/4” concrete pins into your garage floor, and then you can lag the lift frame to the spacer blocks. One on each side will keep things from going anywhere. In my situation, it’s installed in a shed with a wooden floor so it is fairly simple to secure to the floor

[@kevinnice760]

It doesn’t look like it was all the way up, was it out of stroke or did you stop it early?

[@travisgray3331]

Where did you drill the 1/2 inch hole again on each side and is the 3/4 pipe just welded to the center of the base of the jack?

[@matthewreed3799]

Can you add links to the parts you purchased to do this? Awesome idea

[@tripplecrossproductions7544]

matthew reed www.harborfreight.com/1000-lbs-steel-motorcycle-lift-68892.html m.harborfreight.com/21-gal-2-12-hp-125-psi-cast-iron-vertical-air-compressor-62803.html m.harborfreight.com/20-ton-air-hydraulic-bottle-jack-69593.html

[@jacobcardenas9678]

hi I just finished converting mine to air works good going up but table will not close completely coming down like original jack, i think my 12 ton jack is just like yours any suggestons.

[@SgtFury1122]

What was the inside diameter of your 3/4 hollow rod? Was it a snug fit for the .5 steel rod? Nice video. Trying to mod my lift now after it got stuck in the up position with my bike on it!

[@darrelllarrabee4179]

Great job!

[@ruinneder97]

Did you have a problem welding the steel pipe to the cast iron base of the jack?

[@mrkang4080]

Weird question: how big is that mat under the lift?

[@francispetaluma]

nice job!

[@johnhonyoust2197]

what did you do to get the jack to work horizontally??

[@Josell1028]

Which welder model did you use?

[@tjt6288able]

Do you think a 6 gallon air compressor with max 150 psi will work?

[@glenngorman5957]

In your comment you mentioned that this, part 2 is the final painted video. Where is part 1? Does it have the measurements and show more details of what you did? I sure wish that you had talked about the measurements. Like how far away from the brace did you drill the holes for the pipe.

[@quintonwrenn5094]

Did u tack the 3/4” pipe to the 1/2” pipe or is it rotating on it

[@michaelnesteby8985]

Question, does your table sit all the way down when you let the air out. I copied this on mine but the ram bottoms out before the table goes completely down

[@twistedmetriccycles]

Cut the springs off the jack, it will go up twice as fast.

[@rjoseph1100]

I recently purchased this lift and also have a ultra limited and thinking of converting to air, nice video by the way. With the pump mounted like that, will it raise the table fully? I noticed you didn't slide the bar into the highest point of the table? let me know. I did install removable side panels makes it so much easier to load and unload my bike

[@bikemancody2752]

I noticed the same thing. I wonder if it goes any higher as well for the 2nd pin holes

[@terrysmith8714]

Good Job.

[@davejordan6636]

Nice job! Thank you

[@crownline196]

Dave Jordan , thank you👍🏻

[@raelynnreilly6787]

I just got one of these lifts. I have an 07 ultra classic and my manual says GRVW is 1259 shipped from factory . How is yours only 800 and some pounds just curious because it was all me and my uncle could do to even move the lift with straps for help once I rode it up on the lift.

[@dsruddell]

GVWR (gross vehicle weight rating) is 1259lbs so that means with rider/pass fuel and luggage it can weigh up to 1259lbs. the empty weight is around 800lbs

[@alanstrange7077]

Where is part 1?

[@richardcrouse9074]

Where’s the safety to keep it from accidentally falling?

[@rodneyhanbaum697]

Nice job! thank

[@ThePerfectSeason1972]

Why did you convert to air?

[@shadbolen1217]

is that wheel chock from harbor freight as well?

[@crownline196]

shad bolen, yes it is, they sell two styles but this one was rated for more weight. $59 well spent. It’s fully adjustable and well made

[@harleyguy932]

Hey bud. I’m fixing to do the same mod to mine. How is the jack holding up being on its side? I’ve read these jacks aren’t made to operate on their side. Did you have to add fluid? Rebleed?

[@tripplecrossproductions7544]

Ricardo Gonzales yes, we added more fluid to have it function properly

[@kevincrookshanks2896]

where did you buy your wheel dock?

[@garyjohnson3108]

I meant my buddies 2,800.00 lift doesnt do the wobble.....

[@jdshooter777]

what rectangular cross member are you referring to? thx.

[@bill1374]

The one at the bottom of the jack.

[@Bass.Player]

Very good, you may want to put some extensions on the side of the lift so you have a place to put your feet as you are coming on and off, it makes a big difference and you have a place to put your tools and parts while working. Here is a picture of my goldwing on the lift. i.imgur.com/ZLzrPzR.jpg BTW: this lift is 10/12 years old and the pump is just starting to leak, I have a new one on the way.

[@steveclark2103]

i.imgur.com/oU4tKZJm.jpg?1

[@steveclark2103]

Click on this link.i.imgur.com/oU4tKZJ.jpg?1.to see this kit adapted to a HF lift,the round bar on the table is one of three,an extra.www.ebay.com/itm/20-Motorcycle-Table-Lift-Side-Extension-Kit-for-ATV-Servicing-Use-BW-1000A-SID/312544573351?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2060353.m2749.l2649

[@christhompson200]

Nice!!

[@ricklloudermilksr.5881]

why the mods to it????

[@goodboyringo9716]

These cost 450 .00 now.

[@craigsevyn]

Easily the best conversion I've seen on this lift. Question, do you believe a 20 gallon @ 125 psi is enough to push this table with a full dressed Harley? Again good job!

[@jackprice3108]

craig corbin I would believe so, but don’t take my word for it

[@crownline196]

The compressor I use for this lift is a 25 gallon upright, it has no trouble raising the table👍🏻

[@waynerobinson2301]

craig corbin you bet it will

[@FC64002]

Craig, yes it will

[@hardracer]

How heavy is that bike?....my mower is about 1200pds that I want to lift..I need come up with something like this but adapt it wider. Top and bottom..I like your air settup.

[@jackprice3108]

hardracer I believe the bike is approximately 860 pounds. But good luck on the project! I’m excited to see more diy projects!

[@hardracer]

Thank you sir for the reply,,I did some measuring...my table is gonna have to be in the area of 48"wide,it can be done though I'm sure of it..just gotta do some more thinking as to the beefyness of it with my weight of the mower along with the weight of the lift..your video is a great inspiration for my thoughts.im thinking more along the lines of a scissor lift type settup now....thank you!

[@tripplecrossproductions7544]

hardracer cool stuff! Hopefully it all works in your favor!

[@am3121]

Harbor Freight lifts are rated for 1000 lbs.

[@geneva93]

I like your modesty especially when you say "it worked for me" but I'll tell you, if anybody did a better job than you on this lift conversion then he hasn't posted it on KZbin yet!

[@dr.mikedaydccme4606]

Awesome

[@wb4514]

There's no room for your feet once you get the bike up there !

[@jonkagan9524]

Hey bud, I copied your project exactly but the air side of my jack won't work. I've read several posts that say the air side of these jacks don't work when configured horizontally. I thought the air motor may have got damaged during the welding of the 3/4 inch pipe so I went and bought a new jack and was super careful during the welding. The air jack worked prior to the horizontal mount but failed to work afterwards. How did you get yours to work?

[@hardracer]

Jon..I dont know how these bottle Jack's work Inside ..but maybe check fluid if and add more when horizontal..just something else to check if you haven't had that thought...does sound like a fluid issue though and makes sense on what u said about laying horizontal of not working.personally I would tip that sucker every way I could while filling it .might work,give it a shot.

[@jonkagan9524]

Thanks @@hardracer . I will give that a try. I'm gonna call Harbor Freight when they open up and see if they have any suggestions. I'm not giving up and will post up what I learn.

[@jackprice3108]

@johnkagen Sorry I didn’t get to your question, but yes, we added more jack oil and worked horizontally as shown in video. This is me but on my other account by the way.

[@jonkagan9524]

@@jackprice3108 Jack, I added fluid to the jack, bled it properly and damn, the thing works perfectly. Thanks so much!!

[@jackprice3108]

Jon Kagan that’s good

[@mandel7172]

Care to make one for me? For a fair price of course.

[@crownline196]

al mandel, where do you live? Shipping wouldn’t be cheap I’m sure

[@mandel7172]

@@crownline196 33178. What does it weigh? 20lbs?

[@dannyabbatiello4456]

This is actually a fantastic video and my opinion is this would sell on E Bay and would be a hit for those of us owning or even thinking about a Harbor Freight lift, And if you do start selling them on E Bay I hope you announce it and share the link here, Again Great Video @@crownline196

[@crownline196]

danny abbatiello thank you sir! I’ve considered making another one for that reason, I think they’re definitely marketable

[@motorcitymadman146]

This was BC ( Before Covid ) lol Go Brandon

[@martinhauk1852]

I have the Central Pneumatics motorcycle lift table from Harbor Freight, (the predecessor to the Pittsburgh) that came with the air/ hydraulic jack. After about 12 years of frequent use, the pneumatic pump gave out and I manually pumped it up for about a year. I eventually converted it to a hydraulic cylinder powered by an electric pump. It was a good lift. Now it's a great lift. P.S. Do you have the original angular front wheel stop from the wheel clamp. I'm looking for one. Here's the link to the video on the mods I did. kzbin.info/www/bejne/imfIeZ2ej7Oejtk Here's the video on the conversion I did on my second lift. kzbin.info/www/bejne/j3XJm6eQg5p0gNk

[@RTAMechanic]

Tha

[@brada4018]

That thing is a piece of crap.