In this episode, we are trying to dive a little deeper than normal. Let us know what you think in the comments. Do you want more videos like this? Do we talk to much? Let us know!
@A.R.K.Fab.12 ай бұрын
More tech! Love this shit! More of this on track days would be awesome!
@tdhbb8 ай бұрын
So glad i found this channel. i learned like 8 things atleast. subbed for life!!
@TailoredChassisSolutions8 ай бұрын
Welcome aboard!
@Eyelise20058 ай бұрын
I was wondering since my engine has been sitting dry after a rebuild for a while. Good to know.
@rderder1128 ай бұрын
Seamus wearing that one glove makes me laugh. Seems like a good opportunity to use a endoscope/borescope camera to give a technical view point.
@TailoredChassisSolutions8 ай бұрын
Its 2 gloves, dirty sides facing each other. Good thinking, buy me an endoscope!
@m-specgarage8 ай бұрын
This is Awesome! Thanks for sharing your knowledge with us man! ;)
@lowkeeThings8 ай бұрын
The goat getting shit done I see you homie
@PennywiseM38 ай бұрын
Killer video! Love the attention to detail 👍
@G_Ozare8 ай бұрын
Good shit boys. 👍
@fastturbo8 ай бұрын
Beautiful video
@DustinHover8 ай бұрын
Love it !
@leoiggs206Ай бұрын
Good good good that make me happy boooiiii
@oat.cortadhoe8 ай бұрын
I love tech tip videos and tutorials. Do you pre-fill your oil filters as well? I notice a lot of KZbinrs don’t do this and I cringe a little at the dry start.
@TailoredChassisSolutions8 ай бұрын
The pre-priming process fills the oil filter as well. On a routine oil change procedure it depends on what angle the filter is fitted and its not always possible but I prefire the engine and prime the system prior to an oil change so its not likely its lost primer and dry cranking. Its not always one-size-fits-all
@arlokkkk8 ай бұрын
Thanks for sharing! Those tools are cool! Which port would you use to pre oil a rb25? Thru the turbo feed? I also want to make sure that my oil cooler is installed correctly before starting the car. Is this much better than prime crank? Thanks!
@TailoredChassisSolutions8 ай бұрын
Where ever the oil pressure is sourced from on an engine is a good place to start and close to the beginning of the oil flow path. They are also a consistent thread typically 1/8BSP on jdm/euro and 1/8NPT on USA but not always in both cases. The pressure will allow back filling in both directions and then cranking prime after is a confirmation of pressure building.
@arlokkkk8 ай бұрын
@@TailoredChassisSolutions very good to know. Thanks!
@arlokkkk8 ай бұрын
@@TailoredChassisSolutions I have one more question if I may. Should I be doing this pre oiling to a used stock rb25 that it's been sitting for 8 years or crank prime should be enough since is not a new freshly built motor? Thanks!
@juliushon6663 ай бұрын
I see you have the PRP crank & cam trigger kit and also hooked up the HKS V cam sensor. Does this mean you 3 "reference points" for the ECU? (Intake cam, exhaust cam and the crank)
@TailoredChassisSolutions3 ай бұрын
@@juliushon666 correct, in haltech speak it's trigger/home/spi1 for. Trigger for crank, home for exhaust cam, spi for intake cam
@juliushon6663 ай бұрын
@@TailoredChassisSolutions ah ok thanks. Coz I’m considering between a hi octane cam & trigger kit and the HKS v cam crank sensor only kit. Not sure if only having 2 reference points affects the tuning accuracy or difficulty.
@skettirides8 ай бұрын
Why do you put two gloves on one hand?
@TailoredChassisSolutions8 ай бұрын
I normally wear gloves but the gloves get dirty and if I want to handle something quickly without wasting perfectly good gloves or having to blow the fingers back out and make it sticky and sweaty to put back on, I pull the glove off the hand i want to use, its now inside out and it put it dirty side to dirty side OVER the other dirty glove. I now have 2 clean dry hands to handle clean things. Then when I pull that glove back off the top of the other dirty glove its now right side (dirty side) out again and its dry so it slips back onto my hand easily. It saves me like $100s a year in gloves and reduces waste. If youre a gloved professional try it and youll see what I mean.