You know you have always wondered if this would work. Let's find out! Check us out on INSTAGRAM and see what we are up to between videos! hnxmedia #GreatStuff #ExpandingFoam #TireRepair
Пікірлер: 126
@gphilipc20313 жыл бұрын
You need a "Welcome Back" ceremony...for Mr. Cotter pin.
@HNXMedia3 жыл бұрын
This comment deserves LEGENDARY status for the reference!
@daveharner111 ай бұрын
I did this twice on my lawn trailer tires and wasted 2 cans of Great Stuff trying this. The foam never expanded or solidified. I contacted the manufacturer and was told that the product needs MOISTURE to work properly. On my third attempt, I injected about 2 ounces of water into each tire, spun the tirs to distribute the water evenly, and then re-injeccted them with Great Stuff. This worked out very well and gave me great results! The manufacturer was adamant, however, that THIS IS NOT AN APPROVED USE OF THEIR PRODUCT.
@HNXMedia11 ай бұрын
LOL. I imagine they would frown on this use. However, here is my follow-up video: Expanding Foam in a Tire (Four Year Update Review) kzbin.info/www/bejne/hGG5e5WBZd99d5o but still recommend my Pool Noodle video the most.
@bl98984 жыл бұрын
I used to work for a commercial tire shop that had a foam filler for the big tractor tires. As far as expansion goes I don't know if there was that much expansion. This is due to the filler you are using is for filling cracks around doors and windows, thus the need for expansion. The foam we used was monitored with a pressure gauge and there was a needle driven into the tire opposite the valve stem for venting air. When putting the foam fill in the tire the valve stem was on the bottom and the foam introduced until it started to bubble out through the pin in the top. At this time the pressure was obtained, the pump was shut down, valve replaced in the valve stem, and a nail used to plug the vent hole. Then curing. 24 to 48 hours, depending on how large of a tire we did. And we did several rear tractor tires. And these weren't garden tractors.
@HNXMedia4 жыл бұрын
Thank YOU for these tips and information. I should certainly have been more clear about how the foam needs air to expand and set-up. The needle in the opposite end is brilliant! Thanks.
@tetonper64283 жыл бұрын
Wondered about how the shops did it. I had a friend who would take my wheelbarrow and lawn tractor tires and do them at his son's shop. Never knew how they did it but no more flats!
@jackalley64512 жыл бұрын
tHIS FOAM DOES NOT WORK IN LAWNMOWER TIRES
@mateobrainardo47702 жыл бұрын
@@jackalley6451 WRONG!! This method ABSOLUTELY performs WONDERS in the rear tyres of my MURRAY 42” double fuxxer. I’ve BLOWN them FULL of pFOAM, 2 years ago, and performa perfecta, AMIGO!
@johns30812 жыл бұрын
You could probably save the needle valve for another project and just screw a cap onto it.
@HippocratesGarden3 жыл бұрын
Hint, fill a ballon with some of this, let it fully cure, then, flatten a spot. Does it rebound? nope, stays flattened. Might be fine for a lightweight push mower tire, but that's about it.
@HNXMedia3 жыл бұрын
Yes, that is why I have reiterated in many comments that this is NOT for "weight bearing" tires or anything a living being would be transported upon. Small carts, pressure washer as shown here, etc only. Peace.
@michaelharings99133 жыл бұрын
You can also drill a few holes around the tire, to let the foam expand more evenly, you don't have to remove the valve stem. (I saw another youtuber do that.)
@HNXMedia3 жыл бұрын
Absolutely! I have done that since and it works much better.
@ralphwood88183 жыл бұрын
When you add foam thru the valve stem with no way for the air to escape you end up with a tire full of foam and compressed air. As long as the compressed air doesnt leak out it seems to work. You have to have at least one air escape hole. If the air bleed hole is too small it might clog before the air escapes. I blew up an old tire once. Luckily it happened when I wasnt around. If you dont have a mess to clean up you didn't do it right. It still wont work for weight carrying tires.
@thestone46 Жыл бұрын
LOVE the twisted wire "Jesus" clip holding the tire on to the axle.
@HNXMedia Жыл бұрын
LOL. Nice catch! I have since replaced him t with a real cotter-pin. Thanks for watching and leaving a comment. This one made my day!
@Wakeupandsniffthecoffee2 жыл бұрын
My tube has gone bad many times. Pain in the rear and the wallet. I'm moving wood chips around the yard with my John Deere mower trailer and have one tube that went bad and sucked up into the tire. No valve stem is protruding. I notice that even with that weight in the tractor, the tire holds it pretty well. Thinking if the tire with a blown tube can handle the weight, then a foam filled would probably work. Not a fan of how expensive the foam is and the sticky mess, but I may try it.
@HNXMedia2 жыл бұрын
Honestly, I would suggest this instead: Fix a Flat Tire with a Pool Noodle - DIY Run Flat Tire kzbin.info/www/bejne/qajFXpqHeK6Xm9U
@solosailorsv80652 жыл бұрын
install a TUBE (old school) ..... but foam is more FUN ! (needs a 2-part curing foam with air escape around the rim)
@HNXMedia2 жыл бұрын
Thanks for watching! Coincidentally, I have a follow-up video to this video dropping this weekend if you're interested. Thanks for posting a comment and stay well.
@carfvallrightsreservedwith66497 ай бұрын
2-3 holes drilled in tread gives escape route for excess foam. Also lets you know if complete interior was filled.
@HNXMedia7 ай бұрын
Absolutely. Here is another idea: kzbin.info/www/bejne/qajFXpqHeK6Xm9U
@Xoman087 күн бұрын
I am going to try this on my tubular tyres on some of my bicycle wheels.
@HNXMedia6 күн бұрын
I recommend against it, but you do you.
@braybray76252 жыл бұрын
man sounds like barrack obama, pauses and everything 🤣
@HNXMedia2 жыл бұрын
This comment absolutely made my day...and its only 6am 😎
@Elsanta66610 ай бұрын
Have the stem on the bottom side drill a small hola on top of treat for the air to scape and room for the foam to expand
@HNXMedia10 ай бұрын
Great call!
@MikeMike-is2hl2 жыл бұрын
Don't need the valve stem anymore, just put the cap on.
@miguelquazar8838 ай бұрын
Wouldnt it make more sense to allow the foam to leak out until the stream stops, then replace the stem?
@HNXMedia8 ай бұрын
Yes, it would. It will allow air in to make it cure faster. However, I would actually recommend this fix instead: kzbin.info/www/bejne/qajFXpqHeK6Xm9U
@harleyboy57683 жыл бұрын
Why not just put a cap on instead of the valve stem?
@jerrymcbroom85603 жыл бұрын
Seems right
@bl98983 жыл бұрын
The valve stem was used for more reliability. If you dont want to use a valve stem then go ahead and give it a try. You have no reason to be afraid of experimenting. I suppose you are a citizen of the "currently still free to express yourself United States of America".
@george198411 ай бұрын
You are a genius
@HNXMedia11 ай бұрын
Thanks for watching and taking the time to leave a great comment! Check out the update video here: kzbin.info/www/bejne/hGG5e5WBZd99d5o and maybe an even better method/solution here: kzbin.info/www/bejne/qajFXpqHeK6Xm9U
@freshlycutlawnservice2 ай бұрын
Sweet !!
@HNXMedia2 ай бұрын
Here's another idea: kzbin.info/www/bejne/qajFXpqHeK6Xm9U
@MrGlibguy Жыл бұрын
I've sold polyurethane systems for over 40 years and one can achieve all sorts of modulus using various chain stopping reactions. Urethanes can be light foam or and hard as a rock depending on when the reaction is stopped. The best system for this would be a soft rubbery consistency and filling the tire evenly is also desirable. Just my two cents worth. You just need to find someone with a lot of different formulas that they have experimented with for the best results. There are a few companies i've dealt with that make several different modulus urethanes.
@HNXMedia Жыл бұрын
Thabks for watching and adding great information. See our follow-up video here: Fix a Flat Tire with a Pool Noodle - DIY Run Flat Tire kzbin.info/www/bejne/qajFXpqHeK6Xm9U
@semper-di2 жыл бұрын
Thank you
@HNXMedia2 жыл бұрын
You're welcome. Hope it is helpful.
@user-zx9hs7gx4iАй бұрын
What about a low expansion foam...... I would be afraid with an expanding foam that you may actually pop the tire off the rim...... I've seen that stuff blowout windows and doors
@HNXMediaАй бұрын
Try this: Fix a Flat Tire with a Pool Noodle - DIY Run Flat Tire kzbin.info/www/bejne/qajFXpqHeK6Xm9U
@MASTERSAIS4 жыл бұрын
How good did it work. After a few heavy loads did the tires get oddly shaped?
@HNXMedia4 жыл бұрын
It has held up well for a year now. I have learned a lot from the suggestions in the comment section that I will use next time I do this. So far so good.
@cesarsantellana17683 жыл бұрын
Gave up on using foam and ended up getting rid of the tires as well. Riding on rims takes some getting used to.
@fredrikgunnarsson65182 ай бұрын
I Will try
@HNXMedia2 ай бұрын
This is another, more permanent solution: kzbin.info/www/bejne/qajFXpqHeK6Xm9U
@HarshmanHills5 жыл бұрын
I need to try this on my wheelbarrow if i can get the stupid tire reseated
@arnoldscully89064 жыл бұрын
Did you try it on your wheel barrow? How did it work under a load?
@roberttill37873 жыл бұрын
The problem with your tyre seating is usually modern wheelbarrow wheels are injection moulded plastic wheels. They are so bad they are not round, and the tubeless tyre does not hold air. The cure is to fit a tube in the tyre, or get a metal wheel thats completely round.
@joelsch86274 жыл бұрын
when you quickly put the core in to stop the foam from coming out, i assumed you screwed it in tight, but it looks like may not have because later you showed that air was escaping. can you explain exactly what you did. do you leave the core "partially" reinstalled????
@HNXMedia4 жыл бұрын
That is the trickiest part. You have to allow a a small amount of air in the tire through the stem so that the foam will "set-up" (this type foam requires air to "activate"). If you seal the tire/valve too quickly, the foam will just be mushy inside the tire. Though I do not show it in this video, you can actually cut a small hole in the tire itself to increase the amount of available air for the foam to react with (the foam will eventually seal it back up. But to answer the question, when you're done, the valve is fully installed. Thanks for asking a great question. Peace.
@joelsch86274 жыл бұрын
@@HNXMedia hey i have a little scooter with pocket bike tyres..it only goes about 15mph max. it is about impossible to change the tyre and put in a new tube so i think i need to do the foam.. will it work at taht speed? and how will i know when i have enough foam in? im worried it wouldnt work its way all around and leave a flat spot also. would it be better do drill a hole on the opposite side, or do 3 holes spaced, sidewall or on tread???
@HNXMedia4 жыл бұрын
@@joelsch8627 Friend, I would absolutely not feel comfortable suggesting to use this technique on anything that is designed to support a living being. This is only for yard/farm equipment as a "quick fix." But to answer the last question, yes drilling a hole in the opposite side of a tire would help increase the "air interaction" with the foam (and you would know when the tire was "full." Hope this helped. Peace.
@jefolson698911 ай бұрын
Do you need to spin the tire to distribute the foam evenly? Its just for my garden cart.
@Sebman333 ай бұрын
I would do that exact thing. Just roll it back and forth with some pressure to make sure the whole 360 degree surface meets! Id glad wrap the top of the tire and puncture a whole through the top to let excess air escape and it would help distribute the foam better, dry better and be more uniform. Then use a puncture repair kit to fill the hole. bobs your uncle. You now have an invisible stable tire.
@jefolson69893 ай бұрын
@Sebman33 thank you. I ended up using just 2 holes . One for air escape the other to insert the foam. Then switch halfway through spinning the whole time. If anything I got the first 2 too hard but it's better than flat. Great idea.
@Elmox222 Жыл бұрын
Does this make it harder for random folks to slash your tires?
@HNXMedia Жыл бұрын
You know, it might actually help, however I have not had a lot of trouble with folks slashing the tires on my pressure washer. This might even be better: Fix a Flat Tire with a Pool Noodle - DIY Run Flat Tire kzbin.info/www/bejne/qajFXpqHeK6Xm9U
@gabriel.jewelpure38523 жыл бұрын
Hi - What type of foam did you use - I tried it but the foam turned to rock and did not go all through the tire.....
@HNXMedia3 жыл бұрын
I used "Great Stuff." I have learned that it helps to intentionally punch a hole in the tyre opposite the valve to allw more air in so that the foam will "cure." It will get hard and solid over time and may require a "refresh" if the foam breaks down. This is designed as a temporary fix for non-load-bearing items like the pressure washer shown in the video (or maybe a garden cart) - not a garden tractor or anything that would transport a living creature. Hope this helps. Thanks for watching.
@jerrymcbroom85603 жыл бұрын
Anyone ever do this with inner tunes in tires? Like a bicycle?
@HNXMedia3 жыл бұрын
I have not. I would not recommend this technique for any device or vehicle designed to transport a human being or a live animal. This is only for utility items. Best regards.
@roberttill37873 жыл бұрын
@@HNXMedia The tyres in your video are tubed. The four bolts hold the two halves of the wheel together when you put the tube and tyre on the wheel.
@AndrewBobier10 ай бұрын
Hi that's awesome I have a scooter that is what I wanted to try because of the cost
@HNXMedia10 ай бұрын
I do not recommend this for any type of transport. Here is a potentially better solution: Fix a Flat Tire with a Pool Noodle - DIY Run Flat Tire kzbin.info/www/bejne/qajFXpqHeK6Xm9U Still, not designed for human or animal transport.
@colezee7640 Жыл бұрын
Would this work for a wheelbarrow wheel?
@HNXMedia Жыл бұрын
Try this solution instead. It is better all around: kzbin.info/www/bejne/qajFXpqHeK6Xm9U
@Bigwingrider18004 ай бұрын
Just got done with mine, every frickin year. it sucks
@HNXMedia4 ай бұрын
I found that this actually works better: kzbin.info/www/bejne/qajFXpqHeK6Xm9U
@marshallvisions94103 жыл бұрын
cute doggie.
@HNXMedia3 жыл бұрын
Thank you. She's my baby.
@bbkind24843 жыл бұрын
Someone else did an experiment with different types of foam..the big gap filler works best
@ronfalk6441 Жыл бұрын
How much foam do you put in,?
@HNXMedia Жыл бұрын
Overall I used about a can and a half, and it held up for quite a while. However, this video here shows a FAR better solution for smaller tires: kzbin.info/www/bejne/qajFXpqHeK6Xm9U
@ronfalk6441 Жыл бұрын
Thanks
@artman1024 жыл бұрын
Has anyone tried this on their riding lawn mower tires?
@HNXMedia4 жыл бұрын
I have never tried this on riding lawnmower tires. I have tried a bunch of other methods to get through an extra season (paint & glitter/shredded plastic flakes). In the end, I just bought new tires and tubes. I think a riding mower is just required to carry too much weight for some of these fixes to work. I would only recommend this on "non-load bearing items." Peace.
@mateobrainardo47702 жыл бұрын
I filt the rear TYRES of my MURRAY 42” DUBBEL fuxxer. Two YAHRS agoo. Used 4 (foar) cans in EACH tyre. Drilt 4 (foar) 1” (one unch) HOLS into the rim. It was a RIM JOB. Some people say “it won’t werk”, “yurts jest wasted my time”, but WRONG! I diddit twot yahes agoo, and it took almost a yahr and a hefe to cure. It finally cured and SET UP strong yesterday. So WRONG! All the never say never say nay not sayers; it DOES werk, just makes a complete pFukkan MESS oh JERROLD, lemme TELL YA!
@ralphwood88183 жыл бұрын
My daughter got on my Craftsman lawn tractor after it had been sitting awhile. She said those tires are not around. I will get you new tires. That was the end of that experiment. I have heard of people putting the mower on blocks between uses. I've heard of drilling.holes in the flat spot and adding more foam. Hell no.
@kennethlewis716310 ай бұрын
What's your age if you don't mind me asking.
@enriquecasiano79213 жыл бұрын
You pay $10 for the foam $5 for a tube umumum
@HNXMedia3 жыл бұрын
I actually already had the foam, but even at my local store it is only $3.50 (US) - and I have about 1/2 a can left over, so the cost for me would have been $1.75 (US).
@michaelkenefick2 жыл бұрын
Changing the tube is those style tires is a pain. They are extremely similar to a Hover Round Power Chair tire. PS the tubes at HFT used to be about $2.50 - 3.50 each.
@malachi9898 Жыл бұрын
This wont hold up long term. It will destroy your tire. I did thi to my wheel barrow and the tire is pretty much falling apart now. You are better off using Slime. It will puncture proof your tire and keep it air filled and last alot longer.
@HNXMedia Жыл бұрын
Actually, it did hold up for four years. The update video is here: kzbin.info/www/bejne/hGG5e5WBZd99d5o But truly, this is a better solution: kzbin.info/www/bejne/qajFXpqHeK6Xm9U
@DanBollinger33 жыл бұрын
Not a good solution. This is low-density, rigid foam. You want high-density, flexible foam like Smooth-On's FlexFoam-iT! 25.
@HNXMedia3 жыл бұрын
Good call. I found an additional solution that I will be making a video on very soon. Thanks for the info. Peace.
@rudyyarbrough51223 жыл бұрын
If his tire was truly full of foam he would not have been able to squeeze it like he did in the video. The best way is to lay the tire on its side and drill four holes on the sidewall and then allow the foam to expand and come out all four holes. The foam can expand like it should and the excess is easily cut off from the four holes.
@HNXMedia3 жыл бұрын
But, see, it was full of foam, but just not set up yet. Yes, it helps a lot to have an additional "puncture" in the tire since the foam needs air to truly cure. In this video, I do not show that, but the foam in this tire still cured over time (about a 1/2 hour). Thanks for watching.
@roberttill37873 жыл бұрын
@@HNXMedia Foam takes about 12 hours to fully cure and thats in conditions of open air. In a tyre it would take days to cure fully.
@mateobrainardo47702 жыл бұрын
@@roberttill3787 I filled the REAR tyres of My MURRAY 42” dubbel FUXXER twot yesrs ago, and it finally got cured yesterday.
@roberttill37872 жыл бұрын
@@mateobrainardo4770 Thats why the poster says you need to drill holes in the tyres, but why destroy a perfectly good tyre, just get the puncture repaired. Something better would probably be the puncture proofing slime. We had a car tyre in our works as a demo, and used to stab it daily and it took weeks to lose pressure. It was like a sieve.
@edgenet14 жыл бұрын
Why do you care if the tires go flat on a power washer ???
@HNXMedia4 жыл бұрын
This is not one of those cheap ones, it weighs a ton. I pull it up and down steps all the time. When the tires are flat it makes that part of the job a lot more difficult because it is prone to tipping.
@mateobrainardo47702 жыл бұрын
He jest cares allright? Jeez, cut the sman a piece of SPAM? Oh JERRY!
@stanleykeith69694 жыл бұрын
I tried this, it works at first and then it starts to brake down inside the wheel. I used 4 cans. Best to do it on a Hot day. Two wheel lawn cart. I still had to buy myself 2 new tires. The price of those cans are not worth it, 4 cans + tax= 1 tire from Harbor Freight.
@HNXMedia4 жыл бұрын
Valid points. Thanks for watching and adding to the conversation. Peace.
@ralphwood88183 жыл бұрын
I pissed away a lot of time and money trying to do this on a Craftsman lawn tractor. This kind of foam can't handle a load for very long. The lawn tractor can take Chevy wheels. The thicker car tires dont pick up hedge Thornes so bad. I will be getting flat free tires for the front. I have a couple of 8 inch tires that have been filled at a heavy duty tire shop. If I use them I will need to weld in different wheel centers. Not sure what is in the professional filled tires but they are very heavy.
@mariekiraly1004 жыл бұрын
How do you know when to stop? Since that's expandable foam, if you put too much, do you know?
@mateobrainardo47702 жыл бұрын
When I filt the rear TYRES of my MURRAY 42” DUBBEL pFUXXER, I used 4 (FOUR) cans of expanded FOAM on each tyre. That was twoir yahrs AGO, and it finally CURED yesterday.
@grazynazambeanie59632 жыл бұрын
Buy inner tubes . Foam only works until the tire rotates under load
@HNXMedia Жыл бұрын
Naw, did this instead: Fix a Flat Tire with a Pool Noodle - DIY Run Flat Tire kzbin.info/www/bejne/qajFXpqHeK6Xm9U
@MikeMike-is2hl2 жыл бұрын
Wait at least 24 hours... no air in there...
@HNXMedia2 жыл бұрын
Got a new trick with this coming soon!
@MrMawnster2 жыл бұрын
air doesn't help any reaction with this stuff. For polyurethane moisture does.
@HNXMedia Жыл бұрын
Fixing it this way, however is permanent: Fix a Flat Tire with a Pool Noodle - DIY Run Flat Tire kzbin.info/www/bejne/qajFXpqHeK6Xm9U
@jeremyscott66413 жыл бұрын
You filled it with more compressed air then anything.
@HNXMedia3 жыл бұрын
LOL. There is not even remotely enough compressed air in that can to fill up that tire. Now yes, some compressed air goes in with the foam, but the foam is what fills the bulk (if not all) of the case. Works even better if you put a hole in the tyre opposite the valve as others have suggested (that way you know when the foam comes fills completely and "air" causes the foam to cure faster).
@robertminear40563 жыл бұрын
After a while the foam will start breaking down. I recommend not using it either put a tube in it or replace the tire.
@Casmige2 жыл бұрын
Water (NOT “air”) activates & accelerates the set-up of the foam. It’s the humidity in the air that activates & accelerates the setting up of the foam not the air: it doesn’t air dry....smh Might consider putting some water inside the tyre first, swishing it around PRIOR to filling it with foam. Big Gap is the best. Not the window & door. Not the regular stuff either. You’re welcome.
@HNXMedia Жыл бұрын
But this was more fun: Fix a Flat Tire with a Pool Noodle - DIY Run Flat Tire kzbin.info/www/bejne/qajFXpqHeK6Xm9U
@fineskills15 ай бұрын
Please don’t bad advice ! Save the great stuff for insulating your house, just put a tube in tire they make heavy duty! no mess ,toxic stains on hands or waste of gloves, no waiting around , carry the full load and offers air suspension🤣 I have used old tubes to line the tires with holes worn right through, then inserted a tube in no problems. don’t be lazy and fix it right when are you gonna have time to do it again?
@HNXMedia4 ай бұрын
Or you could do this: Fix a Flat Tire with a Pool Noodle - DIY Run Flat Tire kzbin.info/www/bejne/qajFXpqHeK6Xm9U
@TheDronzDr2 жыл бұрын
First of all your filling foam in a tube. It’s not a tub less tire. I would like to see it done on a tub less tire 🛞
@HNXMedia Жыл бұрын
This was more fun: Fix a Flat Tire with a Pool Noodle - DIY Run Flat Tire kzbin.info/www/bejne/qajFXpqHeK6Xm9U
@TheDronzDr Жыл бұрын
@@HNXMedia 😆
@williamstacey14644 жыл бұрын
Please don’t do this this is the stupidest thing I’ve ever seen...
@HNXMedia4 жыл бұрын
Yet you watched and I thank you for that. Works for me. Still solid a year later. But hey, to each their own. Peace.
@laikynsdad4 жыл бұрын
I did this on my barrow..6 months later she's still pumping. what's your issue?
@SeeMooreVids4 жыл бұрын
Are you kidding me?
@HNXMedia4 жыл бұрын
Nope. If this was the strangest thing I'd done on my channel, I would have a lot fewer videos. Peace.