just an idea on how to rebuild a HOLLEY 3310-2 vacuum secondary thanks for watching
Пікірлер: 61
@Petewasrobbed8 ай бұрын
I am about to rebuild my 1st carb. It is a 4160 with vacuum 2nds. This gives me a little bit more confidence to attempt myself. Thanks.
@bobwilkie15 жыл бұрын
Thanks Chris! I will try my first rebuild tomorrow on the same carb.
@Rick-Williams596 жыл бұрын
Chris, you do great videos. Very professional with explanations so the amateur mechanic can follow along. I've been repairing automobiles for over 40 years and I still learn something from your videos every time I watch one. Thanks man, and keep them coming.
@chriscraft770224 жыл бұрын
thank you, from the heart.. i come from a car family... they think i am the dumbest motherfucker on this earth...i went to school to become an engineer.. so in an argument.. im a dumb ass school boy.. even though all my gauges work on my 70 chevelle SS DASH and none of theirs do..
@izmailovdavid6 жыл бұрын
This vid helps so much. Thank you
@superfuntime31074 жыл бұрын
8:50 Chris...If that is one of the square gaskets you buy from Holley they are actually die cut. If you peel off the the film that covers the adhesive side and look at it under magnification and good lighting they are actually die cut round. You just need to pick at it to break the circle away from the square. Some may be easier than others to work with.
@mgnt2323 жыл бұрын
Thanks a lot going to be rebuilding soon and this could not be more helpful
@davidgoodwin6584 жыл бұрын
I have a Holley 1850 and it has vacuum secondary. I took it apart and it was missing the thin plate and thin gasket. the small secondary plate was screwed directly to the blue gasket. Now I have to look in my spare parts stash. Great video and explanations.
@coolhandluke15033 жыл бұрын
I'm 99% sure the 1850 doesn't have the secondary metering plate.
@MattsRageFitGarage Жыл бұрын
If your 1850 has a solid secondary sealing surface and no power valve channel/cavity it will not have that steel shim plate behind the secondary metering plate. The shim plate was only used on carbs with the seconary power valve cavity cast into the main body, which are usually the older carburetors.
@TheCanadianBubba11 ай бұрын
@@MattsRageFitGarage - Thanks for mentioning that, thought it missing might be a reason why mine is flooding so bad...
@MattsRageFitGarage11 ай бұрын
@@TheCanadianBubba If it's missing the plate and it needs it, it'll cause all sorts of weird issues since the metering plate can't seal to the gasket with a big void behind it.
@davidgoodwin6585 жыл бұрын
Did not know about the check ball on the Vacuum canister.. Great video Chris.
@chriscraft770225 жыл бұрын
some people say they dont have one but im sure they dropped it on the floor.
@vdanisanber34875 жыл бұрын
@@chriscraft77022 what diameter have the ball vacuum?
@chriscraft770225 жыл бұрын
@@vdanisanber3487 i have it in the beginningof holley throttle repair video and blow out protection.. part 6 or 7
@vdanisanber34875 жыл бұрын
@@chriscraft77022 thank you so much
@hedgepethracing9590 Жыл бұрын
They all should matter. They all should be done the same. You do good work don't sell yourself short. My old man told me if you ain't going to do it right just don't do it at all-
@Dodgechallengersixpack4 жыл бұрын
Enjoyed the video. Trying to learn about carbs for my 6 pack setup on my 440
@chriscraft770224 жыл бұрын
you have videos?
@chriscraft770224 жыл бұрын
just do like i do .. there are a lot of BS channels trying to show off like they KNOW secrets.. there are NO secrets.. just rebuild it.. to factory specs.. and have a car that starts up like mine.
@a50cobra Жыл бұрын
That you for posting
@1949kf6 жыл бұрын
Warped secondary metering plates are common causing leaks . Cheap fix is to remove all gaskets and screw metering plate on the carb body with only the thin metal shim/baffle underneath. Torque down the screws. This will usually straighten the plate to conform with the carb body surface. Also, cork bowl gaskets give a superior sealing surface. Solved the dripping out of the secondary idle transfer slots.
@chriscraft770226 жыл бұрын
I almost hope my carb does that so I can make a video on it.. thanks for the info.. how does the carb run? What engine do you have it on?
@AntonioGarcia-dw1mt6 жыл бұрын
Hey Chris I've been building a 85 c10 with a 350 abc for a few years now and been following multiple of your videos. Just about ready to do the initial break in I'm also in the houston area was wondering if you would mind giving me a hand to make sure everything goes out ok. Really have been stressing the break in procedure.
@malc10124 жыл бұрын
so this one didnt have a brass float in the primary and a nitrophyl for the secondary?
@cg28604 жыл бұрын
Hey Chris good video where are you located at
@jerrycollins50484 жыл бұрын
I noticed on throttle body gasket (in new kit) has open holes in two spots on gasket. I'm original owner should I block off? I can send you a picture. Awesome video!
@ebersalcido88104 жыл бұрын
As i was rebuilding my 3310 i noticed that im missing the metering side backing plate. Its that this shim like plate that goes behind the metering plate. How important do you think that pieces is especially being that the boat ran pretty damn good without it this whole time
@coolhandluke15033 жыл бұрын
If it's a 3310-1 I don't think it's supposed to have one.
@ebersalcido88104 жыл бұрын
Bought a bought with a 3310-4 everything so far looks almost the same. I did realize that im missing the backing plate on the secondary side. I do have the metering plate but not that thin backing plate. How important can that plate be? In your opinion
@robertrobertson39272 жыл бұрын
SOME COME THAT WAY , MY QUESTION IS HOW THE GASKET GOS
@tynandill92610 ай бұрын
What if you don't replace the vacuum secondary check ball ? Whistle and create a vacuum leak ? Lost mine playing with springs, and now I have vacuum leak symptoms and whistling ?
@chriscraft7702210 ай бұрын
sounds like it would do something like that but I’m not sure
@thangamajig3 жыл бұрын
What difference will the secondary diaphragm check ball make? Mine don't have one.
@chriscraft770223 жыл бұрын
it probably won’t matter for daily driving.. I’m not sure what happens.. it could keep secondaries open a bit longer or closed.. I will need to research that
@tonioalexander48706 жыл бұрын
What happens if you don’t put the thin metal plate in the rear
@chriscraft770226 жыл бұрын
Why would you NOT put it in? they are under $10 shipped to your house
@grantlucas66783 жыл бұрын
I am rebuilding this carby can some one tale me what this is
@1949kf6 жыл бұрын
Rebuilt a 3310-2 (working on carbs for a living) and gas slowly leaks out of the secondary idle transfer slots just above the secondary plates.Do a web search they all seem to be giving problems. Tried everything. All idle vents clear running out of ideas . Considering just blocking off the passage to prevent fuel from reaching the transfers and emptying bowl and rich running. What the hell does it need transfer slots on the secondary side for?...especially with vacuum secondaries that open gradually. Also the 3310-2 I have did not use a check ball for the secondary diaphragm.
@chriscraft770226 жыл бұрын
i have not ran the 3310-2 yet.... but hearing your problem.. i would put that check ball in the diaphragm and see if that fixes it.... just a thought.. im still new at holleys and the 3310-1 I built runs perfect with no problems.. i will try to get the 3310-2 on when the weather gets cooler... ask that holley guy that has 40yrs experience.. he should know... sorry i cant help
@1949kf6 жыл бұрын
Thanks for the fast reply. Some do not come with a check ball only those with a small slot on the ball seat. This one does not have the slot.and the delay action that the ball serves is done by a restricted orifice in the diaphragm housing. In any case that would not cause leaking fuel while sitting on the bench . Problem turned out to be the metering plate mating surface allowing leakage into the transfer ports. Thanks again and great videos
@bill56belair606 жыл бұрын
Chris is there any advantage to add a metering block to the secondaries of the 4160-3310 carb.
@chriscraft770226 жыл бұрын
NO.. the 4160s are economy automatic transmission STOCK CAM friendly carbs.... my next video is going over the 3310... which is a 4150 series (secondary metering block) and the original performance carb for the 396 big block .. should have the video up in the next day or two.. what engine are you running? i need all the INFO
@bill56belair606 жыл бұрын
With a 435 hp SBC would you go to a 750 double pumper with manual or vacuum secondary's. It is a 383.
@chriscraft770226 жыл бұрын
im about to do a video on choosing the right carb... it depends on the rpm range of the cam... what is the highest RPM on the powerband of the cam?
@bill56belair606 жыл бұрын
I will watch your next video on this and find my spec sheet, it came with this 3310 carb. thanks Bill.
@bill56belair606 жыл бұрын
PS it is a blueprint 383 with roller cam, if this carb gives me good performance that's great.
@deweydodo66914 жыл бұрын
@ 12:12 You will be sorry down the road when those little O-rings fail on the brass needle n seat .
@chriscraft770224 жыл бұрын
i will let you know when they fail
@timferguson86435 жыл бұрын
that linkage is for a Ford or a dodge motor don't need it with a Chevy motor
@tony17986 жыл бұрын
Do you have a video of it running?
@chriscraft770226 жыл бұрын
not yet, but I will make a video on getting it running for the first time / install ( set up, etc.)
@tony17986 жыл бұрын
Chris Craft Thks. And I love your videos. What happened to the body work? You left me hanging how is it coming?
@MegaTroyhamilton4 жыл бұрын
Bad stuff is right. Burns like a mother if it gets in your eyes
@jperkey70895 жыл бұрын
Never heard of the check ball in the vaccum secondary?? I bought a cheap rebuild kit from eBay for $22 & STILL got a new secondary diaphragm?! Wtf Holley?? Lol
@chriscraft770225 жыл бұрын
some nerd was telling me that not all vacuum secondaries use the check ball.. in all the videos where I took them apart I said they weren’t there.. when cleaning I found 3 little metal balls on the floor.. they all had them.. as far as that kit... let me know in the future if it holds up.. I buy Holley stuff because I might sell it at any time.. and if it screws up 2 years down the road they can get mad at Holley.. but yes, I will buy one like you got next time
@jasonconaway69 Жыл бұрын
With these manual choke 3310s, are they internal vacuum for the choke? I’m wanting to convert mine to an electric choke but need to know if it’s internal or external vacuum.
@chriscraft77022 Жыл бұрын
Internal .. very easy to block off
@jasonconaway69 Жыл бұрын
@@chriscraft77022 Ok. Do you don’t need any kinda vacuum for the electric choke? Isn’t it for the pull off on initial start?
@chriscraft77022 Жыл бұрын
the electric choke has no vacuum or heat tube… You just adjust it