Home Made Coal Forge | Champion 400 Blower

Here are some basic tools i recommend to get started in the hobby!
Best Propane Forge. (I own one and highly recommend it)
amzn.to/3Sbalt7
A proper Cast Steel Anvil. (Do not buy cheap cast iron. You will regret it)
amzn.to/3Hzqh3j
Basic 15" Tongs:
amzn.to/42fodHp
Blacksmith Hammer (4LBS):
amzn.to/3u9jCtG
12 Pc. Chisel Set:
amzn.to/47T7HOt
Forging Gloves:
amzn.to/3UdVH6U
Forging safety Glasses:
amzn.to/3vStBEj
Backyard blacksmith (Book of basic blacksmithing techniques):
amzn.to/3vRCQVe
OPTIONAL Equipment.
Leather Apron:
amzn.to/4b8W1dl
Makers Mark Stamps/ Punches:
amzn.to/49aBp2o
"BEWARE THE BLACKSMITH" sign
amzn.to/3vNXCoG
Contact Me:
[e-mail]
(Disclaimer) As an Amazon Associate, I earn a small commission from anything purchased in the amazon link(s) posted in this description. I use these funds to purchase new gear and reinvest into the channel. Thank you!

[@hurstbill]

I've made my own LPG ribbon burner forge , but this is my next project , awesome job mate , sorry , but I'm going to steal your design..love it that much

[@ryanedwards2021]

Well done man . Simple yet so efficient.

[@Hawksalas78]

Best looking self contained coal forge I've seen. Great job!

[@jorgecaraballo1771]

It looks authentic. What the craft of metal working was supposed to be. And yes the portability is great!!

[@Sawdust45205]

One of the nicest designs I've seen. Great job!

[@jamesblue13]

Excellent DIY Forge video. I'm planning to make one very similar to this. Thanks for the added information.

[@jasongross4124]

I have that same blower in my front yard. Great Grandpa bought it for the forge he used for horseshoes. Me and my cousins must have turned the crank a million times when we were growing up. For a while we even moved it by the faucet next to the barn as a hillbilly hand dryer.

[@keyehek1790]

+Jason Gross these champion 400 blowers are worth quite a bit of money... i'd keep it

[@edgarmilson8686]

You did a great job! I liked the welding I could see. Turned out to be a nice forge!

[@haydenparker9500]

mate thats awesome! just looking to start building a small forge to get going, nice work brotha!

[@j.w.m.rhynejr9766]

Awesome setup, thanks for sharing!

[@gator70422]

Excellent forge . Thanks for sharing !!

[@dennisbarringer930]

Great job looks and works really nice

[@SteveOlan]

I like the forge... good job! I am going to have to build one soon, the one I have is not holding up to the heat with me burner coal now. I am sure I'll come back to watch this a third time when I get ready for this project.

[@TheHyde8875]

Steve Olan if you make your fire pot dimensions bigger you can line it with fire brick and it will last/hold up a lot longer.

[@yo.mama100]

The best diy forge on KZbin I've seen

[@imdapopo]

Nice, the hand blower is really cool

[@crunngren1930]

Best one I've seen. Think imma build one similar.

[@spurlockmc]

Very nice build. Gave me some ideas to modify mine.

[@johnw.peterson4311]

I think you did a great job.

[@stevenickels3091]

looks awesome man! thanks for sharing. I am interested in building this for myself, could you share the dimensions you used for the table and fire pot?

[@oscarjoaquin152]

Good stuff! Forging sick!

[@debbieanderson2478]

Like it, you a fine job Thinking and welding

[@troytreeguy]

Nice Build, sweet welds, Be Well

[@christophernewton8474]

Just a tip, in my experience. lighting the forge is easiest with charcoal and a propane torch.

[@tristy-popstheman7622]

th is is really sweet man great job

[@pappy451]

well i think its great! maybe a little larger air outlet in the firebox . to heat a longer piece . very cool.

[@petercasey175]

what kind of Welder do you use? Looks excellent, great craftsmanship

[@Keith_the_knife_freak]

i like your design! !!

[@tazgma311]

Very simple design for your forge

[@michaelwilson2916]

just about the best diy forge on KZbin

[@kathleennawalt9855]

Dear Mr. wilson, Copy that ! Sincerely, Kathleen.

[@88allstarz]

looks like you did a great job buddy

[@jessesommer3182]

That's awesome!

[@budmoore8144]

THAT IS GREAT WHAT A NICE JOB VERY PORTABLE I MADE ONE BUT MINE IS BIG AND HEAVY AND HARD TO MOVE

[@rawbdiggity]

nice forge, nice welds.

[@stevesyncox9893]

Cool job man.

[@loganoneill8671]

looks great bro

[@kabeercb2222]

very good forge in Malayalam language called ula thank you very much for spend your experience and welcome to Kerala India your good tourist destination

[@donktheclown]

The grate on the bottom and assembly is called the tweir... Sounds like Tweer.

[@umeshamarasuriya644]

*tuyere

[@gannondorfmandrag8209]

Mine is kinda like yours, but it looks like its made out of sh*t, (brake hub, hairdryer, a big old metal pipe from an electrical box, and a poorly hand made frame out of random tree pieces) but it works and well, yours looks really slick and professional

[@lasersight70]

it looks great! here's some info that wont actually affect your smithing much. its pronounced "twe-air" and by simple definition, its "a nozzle through which an air blast is delivered to a forge or blast furnace"

[@faronsquare4911]

Very cool!! 😎

[@jiml9944]

Great welding!

[@tomasistudios2618]

I really enjoyed your video. I have made my own forge from scratch. I only wonder if you are loosing a lot of heat with an open system. MY forge is all enclosed and I have great success with cost efficiency on fuel

[@edwhite7475]

Yeah, i want to build one out of bricks -sort of a combo bbq grill and forge. I havent a clue though, just yet.

[@huckstirred7112]

your a damn good fabricator

[@Naplesfrank154]

Great forge, really sweet! I'm in the middle of building one for myself, I'm using a brake drum. Since you have the air intake pipe on a 45° angle , doesn't any debris or clinkers drop into that air line by accident during the everyday working of the forge? Thanks for sharing, it's always great to hear and see ideas from others. 😎

[@michaeldougfir9807]

Frank Daniels: Wranglerstar also had a brake drum for his first forge. If you go watch his forge acquisition and setup videos, you get a broad enough view that you can see what is possible. His is also on a stand. This is not to take away from the current video here. He has something to be proud of. But more information is always good.

[@Naplesfrank154]

Michael Dougfir Thank you so much sir, I will look into his older videos. 😎

[@TheHyde8875]

I was wondering the same thing, but a simple screen tacked to the outside of the square tube before the 2" pipe is fit/welded would remedy that.

[@Mrwhitegoat]

Very nicely do I really like your deign

[@rodeosound]

Looks great the only thing id be concerned with is not being able to pull out the grate

[@eviltwinx]

Getting that 400 for $100 with legs is a steal! Nice! Great forge. Most have fire pot on the blower side. It’s a little easier to crank blower and hold/check your piece when it’s in the fire. Have you’ve been using it a lot?

[@OldSoulMillennial]

I ended up selling if for 350. I purchased a propane forge-master and its just so much more convenient!

[@MichaelBrown-ms6cz]

Bad Ass dude well done

[@ModernBladesmith]

i wanted to make one like this, and i was thinking half inch for the firebox, but you can't really drill through that.

[@christophermelvin2845]

would this get hot enough to forge weld?

[@libbyforgeandfoundry6180]

That was good cool video , man !

[@rajniverma1715]

you should apply a thin layer of clay soil to make sure that your forge does not melt

[@fiddyfresh7350]

Super cool

[@shadowcastre]

RHF.. Nice forge setup! Do you have dimension for it including your firepot? Also.. I think the word you are looking for is "tuyere" pronounced "tweer" thanks for the video.. Shad

[@alessandrolabruzzo9968]

shadowcastre i

[@MikeJones-yf2xx]

I was thinking about making one like that but Il use a brake drum

[@scottreynolds4827]

what i think; the blower needs mounted so you can reach the steel stock in the fire pot and crank the blower. from the video, it looks difficult. like the size of the forge and fire pot. good job. the small holes at the tuyere plate will clog easily. you need a clinker breaker or wide slots if you retain the tuyere plate senario. you bought an entire 400 blower with stand for 100.00? !!!!!!???? You may know now why the air inlet to the tuyere is supposed to be at a 90°. All the many manufacturers knew what they were doing.

[@reddragon6317]

Good going bro . But could replace the crank with any thing cheaper

[@OldSoulMillennial]

If you can't or don't want to make your own forge, I've listen everything you need to get you started in the video description. Thanks for watching!

[@lutherhgrindstonemtn3456]

Hey Man, great job on the forge! I see the date is back in 2014, you probably worn it out by now. Just kidding, that thing is built to last. Oh yeah, I to have a blower just like that one, except mine is still on the tripod. Thanks for sharing, Take care.

[@kalmannelabancz741]

Oivadaspon

[@thedancingbearforge9117]

Got a new set up or just into other things?

[@johnlopez2967]

kool build,WTG...

[@lauraettar1169]

I have just bought the same blower. I was wondering if you had to change the bearing out ever? Mine is gone I haven't opened it up yet was just wondering what type of bearing is in there.

[@OldSoulMillennial]

+Laura r Im not sure about what bearing is needed or how to replace it, but go on facebook and look up a group called blacksmith enthusiasts and state your question and im sure they will help!

[@lauraettar1169]

Thank you!

[@dirkhafner9970]

Very nice

[@alexthepeasant8150]

nice job

[@user-yo7fd5pi7d]

لماذا لحمت الشباك لاتلحمه لتخرج الرماد وتستطيع تنظيفه

[@simonsiron887]

What are the firepot dimensions

[@ThePollaxtroy]

Nice welding

[@OneDayWiserChannel]

Nice job. You don't happen to still have the legs around, do you? I might like to buy them for my 400.

[@OldSoulMillennial]

You know I think I may still have the legs and the stand mount. I have no problem selling it but shipping is likely going to be expensive so you would have to make an offer that would make it worth my time.

[@silverstrings5569]

How has that 1/8 plate in the bottom lasted?

[@joshuagee6717]

Should be I've been using mine it's 16 guage but it's lasted me all of 2 years of daily smithing

[@Finley0312]

What tubing was used from tuyere to blower?

[@OldSoulMillennial]

I just had what every was laying around. I think I used old pool water pipe.

[@kevinn594]

i like it

[@kayteathomas6347]

Cool

[@patrickhance7348]

Nice forg like the blower.you kan send me want?... 🔨👊👍Pat from Belgium.

[@phrodendekia]

Aren't ashes going to get into your blower's hose because of the upwards angle?

[@phrodendekia]

Maybe the air going out of the hose is enough to get ashes out, but would you tell me how it worked out forya please, i'm interested about that single fact. Everything else is really cool!

[@OldSoulMillennial]

Design worked exactly as you just described. Never had an issues with ashes in the air supply tube. Always settled in the ash collection pipe.

[@billycorey7344]

Nice

[@TheMDGeist66]

no clinker breaker? it's been a few years did that cause problems?

[@OldSoulMillennial]

No I'm still very happy with my setup. After running green coal, you will notice the caking of clinkers and all i do is take my fire rake and loosen up the coal around the air outlet. Also after ever other fire ill just pick out the clinkers

[@bigjim6179]

Clinkers? What is this?

[@TheMDGeist66]

+Big Jim when working metal you get Slag or clinkers. it's the leftovers from steel.

[@bigjim6179]

I'm familiar with slag never heard the other word.......

[@coalsauce4457]

i think slag and clinker silicone that turns to (dirty)glass in the hot heat and blocks the air flow holes.

[@huckstirred7112]

i used or tried to use a plastic vacuum hose and it melted in ten minutes . Wondering why your rubber hose doesn't melt

[@OldSoulMillennial]

The rubber hose is atleast 14 inches below the fire pot. Heat rises. It only gets slightly warm down there

[@huckstirred7112]

i am baffled really i am

[@huckstirred7112]

you were right! it was the blower getting hot , from a bad bearings ,du i feel stupid .thanks for the reply

[@jimcooper0]

where do i find "description to purchase"

[@OldSoulMillennial]

sorry I don't follow, did I make an error somewhere?

[@williecrawford7883]

You have great Craftsman's skills from your creative performance.

[@txhogndeerhunter]

where do you get your coal?

[@ModernBladesmith]

you can buy furnace coal from tsc, but try asking some local mennonites where they buy theirs. they seem to be very connected.

[@Swordmkr]

tuyere....say tweer.

[@johnarizona3820]

Good job! Be blessed kid!

[@unchainedpapabear4517]

5 years later. Still using this?

[@OldSoulMillennial]

Sold it for 400 a year ago!

[@JuanMoreno-vp8wl]

I need a stand for my 400 blower

[@hunterrathke3844]

I'm pretty sure it's pronounced "two-ear".

[@lasersight70]

your pretty close! its pronounced "twe-air" it originates from old French, and they had a weird understanding of pronunciations.

[@motosacredvlogs6300]

2:28 its a horse clamp

[@mrmonkeyman412]

It's pronounced Tweer.

[@leeknivek]

man put some grease in that gearbox

[@andykelly688]

fucking savage..

[@TheAtomicDerp]

Nice build, but it is pronounced "tw-ear-ee"

[@ackerkartoffel8627]

100 dollars for a hand blower thats not a good deal

[@ballbeanking]

Super cool