Homemade TRIMMER Scooter / DIY

[@SG-sk3kt]

Dude that's awesome, on top of that, you're probably the only one who actually showed us what you were doing. Thanks :)

[@Amatop3527]

Zz

[@ArizonaChris96]

This is really cool idea. One thing I would do differently though, I would add a chain cover. If you throw a chain from a worn out link it might take some skin with it if the chain fliys off of the sprocket just right.

[@pillatulasi4493]

Df

[@throwawaypt2throwawaypt2-xp8nx]

it builds character

[@mattDIY]

Aeosome 😀😃 good luck

[@screwsnutsandbolts]

Nice build ! 👍

[@aidentoms9964]

You used what you had and made something awesome, I respect it

[@tomstuff460]

I have done those scooters back in the past 3 decades ago. You would have to change the sprocket ratio I believe right now your scooter won't move stand still you will have to push first to get it started especially with the clutch still on it. Also the clutch will burn out. The best way is to remove the clutch weld the lug nut on the motor shaft place the motor as closest possible to the tire with the lug nut firmly pressed against the tire weld motor in place and you're done.(you may have to fill up the tire with more air pressure) to start the motor you have to do is stand on the scooter with one foot with the other push yourself into the motor start and you'll keep driving you will hit about 20 to 25mph guaranteed

[@thomassteele1728]

I really love how you showed us that motor all hooked up to nothing just vibrating and purring on the table. It's a raw obtainable cheap efficient power source. So many ideas. Could I power 4 wheels with 4 motors? Can you combine multiple motor powers like 3 motors to 1 wheel? Magical stuff man.

[@pracoyoraharjo5123]

Shut up guys

[@pracoyoraharjo5123]

Nvm

[@pracoyoraharjo5123]

Hanya hanyah hshshc

[@pracoyoraharjo5123]

T-)sk

[@luzianedrehersales5045]

Oo

[@DUNIAPETERNAKANDANPERTANIAN]

Nice machine 😋👍👍👍

[@glennbrown4572]

I like this scooter great job. I'd only recommend a chain guard. Hope you are still enjoying it after about a year!

[@joedoe4642]

The burnout was the next finishing touch, awesome

[@JohnWilliams-fj1ce]

Kopp kopp kopp kip i9 on o ok pop ok ok

[@Vinterfrid]

No, it was just ridiculous.

[@maddogmaz1576]

Welding over paint, a true DIY'er

[@dorhocyn3]

62cc string trimmer? Wow, that’s “Shaking hands with danger”..... I love it

[@fartingfury]

I have a near-identical engine in a powered earth auger (drills holes in the ground) and I agree with you: When it hits a rock, I reckon the kick from it could easily break your wrist of you weren't holding it the right way. I think that we all tend to forget just got powerful even small engines can be...

[@henryfriedman8518]

What Kindve speed you get?

[@laxmanghate2361]

My kll see

[@MrDrHouse]

There are scooters with smaller engines 💀💀

[@stevenfronz1862]

thanks man I needed this gave me some thoughts about my 3 wheel trike

[@emmabuckley7041]

He can he. Ja. Be cue. Know. Byword. Cush yo he bugs. Ions. Bhsojs. He I x

[@charlesjenkinson5020]

A nice illustration of some mechanical principles - thank you. One of the more subtle issues is that more gearing is required because the centrifugal clutches are more of an on-off device, only fully engaging at over half the full rev range. This means that without the correct set of ratios they are always slipping or only work with downhill / gravity assistance, and a push start is absolutely needed. Am gonna have a go at a 3 or 5 speed rear internal geared hub 4 stroke engine version.

[@connor1379]

Very cool Nice project 👍

[@IZMENI_SEBY]

hello. interesting video well done, but please tell me why the star that is attached to the gearbox? Thanks.

[@meditation.538]

Wow amazing love it

[@alanspring8462]

Happy to subscribe.❤

[@gauchopower5222]

Exelent video brother

[@michaelwoodsdale460]

Wow...look at the expertise of armchair fabricators out there. I don’t know how they carry around the burden of so much wisdom 😂. Nice build - way to be resourceful with what you got 👍🏼

[@mrimbusyt]

Thank you ❤️😂

[@heavystarch100]

🤔🤓🤓🤓🤓🤓👊

[@fromthebackofmymind]

His home had refuse recycling. Hardly a young man of poverty and no means. But yeah, he uses his head. The scooter works and he inspired some kids that now want a stick welder, cutoff saw and drill press. You need the tools to build your dreams.

[@fromthebackofmymind]

Next project honda ivtec and turbo?

[@calebdickerson2138]

Mr IMBUS How fast?

[@indo-babadwivedi1299]

Nice ... Joint silencer .. Love from India

[@Janggut40]

I love it. Thanks

[@BeTep_jlepeMeH]

Классная идея! Советую сделать Защиты на случай разрыва цепи.

[@thebackyardfamilyoutfitter7284]

Hey man great job on using what you got and making a solid simple project I don't give a crap what people say on this you make do with what you got and you did and it looks good and functions.

[@johnnywilliams78388]

This is a great quick and easy diy project for me and my 8yo boy this spring thanks a million and keep up the good work my brother god bless all

[@ramazandemirbilek7949]

A

[@Ignis_1]

Can i have your parts list?

[@dave3130]

Amazingly clever 👍🏻

[@shurik1336]

Маленькая скорость.А ещё сиденье надо, а вообщем неплохо.А главное своими руками, а не куплено в магазине. И ведь это радует!

[@mehmeteminasal7743]

it's a nice project, can you share the scooter dimensions, good work

[@FEXNTGLXW]

Maybe late to the party but beautiful work 👌

[@finbah5706]

I love the brake stand burn out!

[@abridgingpanda7372]

I have taken inspiration to this design and made it an L bracket that screws in just like yours does.

[@Hubcaps219]

Hey love the vid!! Do you think with a different gear ratio, you could go faster? I was thinking you could even use a bike cassette with several gears and you could have a manual shifter

[@iknowlaa]

Yeah, i was thinking the same. I even think i want to try installing battery/starter/sound system/alternator/proper seat/roof/mini fan/etc etc hahahaha..

[@sonnyburnett5514]

Since this video covered needed aspects of the project, I'm not criticizing in any way ''at all'', but simply suggesting. I might've added a brace or braces to that vertical motor mount plate to help prevent your welds from cracking due to motor or bumpy road vibrations, however, since the frame was obviously heavy enough gauge steel that you could use a ''stick welder'', it may not matter. Instead of that plate, I may've welded another plate onto the frame to bolt the motor mount plate onto & added some slots to 1 of the plates so you could adjust the motor's position for whatever reason. Since you added that chain tension idler, the slots may not be needed to adjust your motor whichever way it ''might'' be needed . A very simple, yet excellent build. I've been wanting to build a 4-wheeled version of ''something'' powered with a weed-eater or chainsaw engine. I've torn apart chainsaws & know their drive setup, but since I haven't got around to tearing into 1 of these things yet, I wasn't sure what all was in 1 so this video was ''VERY BENEFICIAL'' in showing how simple the things are. GREAT JOB & GREAT VIDEO, SIR.

[@СашаМедведь-р1в]

ЗАПУЛА

[@mountainviewturning5319]

Pretty neat nice video 👍

[@braaptv6838]

Need to put a roller on to keep the chain tension but solid first little diy build

[@paulovictorfacavocemesmo6057]

Quantos dentes tem a coroa e o pinhão,ficou bom de arrancada?

[@pb1248]

Good work but as they have mentioned you have to put smaller sproket8 to avoid clutch slipping and wear

[@electronic7979]

Excellent project 👍

[@maxwellspeedwell2585]

"...CROCKS! HE'S WEARING CROCKS! YOU'RE DRIVING THIS SMOKE HOUSE AROUND ON A SCOOTER... WITH CROCKS???" From SNL sinkhole skit.

[@jclaudio806]

incredible project if I were I would replace the platinum with a used one and send it to a mechanical turner to machine a flange to fit the pinion for the chain pinion and crown ratio kit I would never cut but It was sensational amazing job

[@mrimbusyt]

Thank you!

[@gtdodgeviper]

Would it go faster with a smaller sprocket on the wheel or would it be more strain on the motor and end up going slower?

[@shawnmckee14]

A smaller sprocket on the wheel would result in less torque but could spin faster

[@ashmontrealty]

Can you tell me where you got the motor mounts? I purchase one of these motors, but it didn’t have a mount included

[@joshuanicholsjr5327]

mother of invention, love when a great idea comes together god bless

[@apristen]

Great! :-) How many teeth on sprockets?

[@mrimbusyt]

13 and 40

[@biscuit_boy8316]

paint over rust?! 💀

[@agp9269]

Bad news

[@kox_puma2668]

Rust is lighter than carbon

[@_._amirabas_._5222]

😍❤

[@gregorypiercesr.794]

Where did you get the gear on the weedeater and what is the tooth count and chain pitch? Very cool

[@eliseizlotar]

You can get one off a pocket quad or a mountinbike which has more gears you need the smslkest

[@gregorypiercesr.794]

@@eliseizlotar thanks for the info, time to surprise the grandkids! 😉😉👍

[@gregorypiercesr.794]

Thanks again

[@eliseizlotar]

@@gregorypiercesr.794 no problem

[@marm1mustafa100]

You need to put a smaller sprocket on engine to allow it to rev higher. That should be going a lot faster for a 62cc engine

[@TomRaily]

Сразу видно что автор не вдавался в рассчёты, из-за этого самокат еле едит и движок только палит сцепление, а нормально разогнать никогда не получится. Проблема в слишком большой ведущей звезже, максимум она должна быть на 8 зубьев, но лучше 6. Сварка это отдельная тема и долго она не проживёт. Для того чтобы пластину на которой крепится двигатель не оторвало в первые минуты, нужно было приварить несколько расскосов.

[@luismartinez4081]

@@TomRaily d

[@mrsolichinn6379]

@@TomRaily no. Th-2uv

[@That67F100Ford]

Hes probably got it geared down

[@КАМИЛМагомедов-о3б]

@@luismartinez4081

[@Vmaxfodder]

Awesome!! If I could add one thing as a scooter designer? I'd mount the all 4 bolts to the engine. It'll last a lot longer .

[@manojkumargangadharan9263]

Bracket holding engine should have been designed to cover all the 4 screws

[@rauleascobedo2]

or on both sides

[@IZMENI_SEBY]

hello! cool idea! Can you tell me how to put a gearbox on a bike? Thanks.

[@eddysanta1213]

Super,cool.

[@engenhariacknv]

Esse motor consegue fazer uma viagem de 200 km?? Colocando numa bike?

[@jorgelugo9078]

Yes

[@phaitoon8183]

Great job

[@mbhenstra5312]

Cool man but wath is the topspeed of it i am making my self one 2

[@Heres007]

very good !! I also made one with a 150cc engine

[@aadeshmorajkar7417]

Good work bro but when the motor is at high speed there would be a need of suspension.

[@OlaftheGreat]

What kind of weight limit could that engine move? Asking for a...friend...who certainly exists and is not me

[@kawinkumsew7475]

ผมเคยทำครับ บิดไม่ขึ้น ครัชก็เปลี่ยนใหม่ แต่ผมเอาถ้วยครัช อันอื่นมาใส่ เกี่ยวกันไหมครับ

[@techstudioup]

Nice build bro

[@SnowingNapalm]

now to put a 1gallon tank and drive it till empty for sport can always pick up a gallon on the other side to drive back

[@lrnzmusique5163]

nice vid hopefully you need to put a reinforcement steel bar on the side of the motor in addition more improvising for the ped itself. ride safe out there! and by nice motor you have ❤

[@jamesburns2232]

The single plate needs more reinforcement to be a robust design. Currently, there is too much flexing and bending and welds be breaking at the bottom frame rails.

[@AnybikeG-blocks]

Make more of stiff like this and post it for us please I see alot of cool things now like and ypu know what your doing obviously

[@david667766]

Smaller sprocket on the engine required, this is just riding/slipping the clutch all the time.

[@knott2897]

Na it just has very short hearing the back sprocket needs to be smaller

[@DWinnie67]

needs smaller front sprocket OR larger rear sprocket !

[@Ash1965..]

Hopeless gearing ratio !!anyone that has done this are laughing 😂

[@АндрюхаВосточный-к1ъ]

Хрошый самокат неодин ласик Радом нестоял 👍,акитайский самокат .

[@aminbenmellah1776]

Did u build the scooter chassis or did u buy it. Plz respond

[@mrimbusyt]

i built it, also i will build second version of this scooter with better gear ratio and frame next week. Make sure you check it out! :)

[@aminbenmellah1776]

Great thanks so much!

[@jasonmelcher2028]

How fast will it go and how big is the motir

[@carlosalbertomesamojica7775]

Great proyect, one question, wich Is that motor?? How can buy one thanks!

[@fmfinlay9602]

49cc strimmer motor

[@ВадимЯхин-в8ю]

Здравствуйте поставил Вам лайк, подскажите как называется часть которую вы от пилили от двигателя?

[@ВадимКузнецов-з2й]

...ни фига себе!-, чё придумал!-, отличный получился мотосамокат!-, необходимо будет доделывать до ума:-ставить крылья над колёсами, кожух на цепь ну и конечно же покрасить!!!

[@ХусанбойИсмоилов-х6р]

❤super❤❤❤❤❤❤

[@stevesmith6058]

Congratulations to a beautiful job it looks professional

[@mouhaahaahaa]

really cool. how did you build the back wheel? i wonder how to put a gear on mine.

[@cariyaskeling514]

Very ideal

[@richarddebideen6371]

Hey what's the top speed on this awesome build

[@ВладЛебедев-м1с]

Рама хлипкая, развалится на первой кочке. Передаточное отношение слишком мало. Нужно хотя бы 9 к 1 (900 об мотора =100 об колеса). Сцепа буксует

[@gs8282]

So simple and good job

[@juliagit9782]

Quantoes lvatra

[@Amilzera]

Top, Cool.

[@ХусанбойИсмоилов-х6р]

❤Good❤❤❤❤❤❤❤

[@sangeetamaharaj3549]

very good

[@dznuttzonyachin7499]

Better be careful at wide open throttle !! you might break speeds of 5 mph and that could extremely dangerous 😁

[@ОлегМошняга]

Это сцепление где звёздочка приварена не расчитано на боковое давление цепи, долго не прослужит. Но лайк за труд

[@AlekseyCamodelkin]

👍🤝

[@ХусанбойИсмоилов-х6р]

❤WOW❤❤❤❤❤❤

[@boyhenyo4431]

I THINK you dont need a high torque gearing for this since the wheel is too small its already high torque its why its too slow.

[@PankajSingh-nu2cg]

Enjin k bare me bataiye sir kuch Konsa h

[@menacingvibez]

From where did u buy the motor???

[@TheReefa24]

what direction does your engine rotate when viewed from the clutch side when running? clockwise or anti clockswise.

[@Datsyukiandeke]

Counter-clockwise

[@garbagecan6969]

how is it able to idle without a clutch

[@marioexpropiacionpetronilo2753]

Very smart and clear video!!! Does that kind of engine have a centrifugal clutch? (It seemed to me) thank you!!!

[@saabturboguy]

its a commercial strimmer engine they all have that clutch bud

[@maxpayz2431]

Whelp, know Ik what to do with my old weed Wacker. Turn it to an epic go-kart/motor bike

[@2.0x5o]

I won't go very fast so I suggest selling it to make money for a pred engine

[@silverwindspirit]

I wonder if this motor will work on a wheel chair

[@polak9576]

Super 👍👏❤️🇵🇱

[@xusanboyismoilov7489]

Super

[@garik_timoshenko]

если не ошибаюсь, то при такой передаче и оборотах в среднем 4500 в минуту....скорость самоката будет около 60-70 км час или буксовать сцепление..поездишь недолго.. шестерня напрямую....значит средние обороты 4500 минимум... это в минуту.. умножим обороты на 60 минут в часе...разделим передаточное на 3, приблизительно... возьмем 10 дюймовое колесо где-то 0,75 метра на оборот... итого 4500*60=270000 затем делим на 3 =90000 умножаем на длину 0,75 и делим на тысячу =67,5 средняя скорость...ну как то не реально....точнее немыслимо...плюс подшипник быстро выйдет из строя

[@nicholasandrews4664]

If you where to swap the sprockets you would lose a little low end power but you could get a higher top speed that 62 cc 2 smoker has the power

[@LiIAxe]

Thank you for the idea, will be doing something similar soon 👍🏼

[@ВладмирВладимир-п9е]

Красавчик! Молодец!

[@lashapap9106]

What's its top speed?😄

[@slicaltimistic1]

Great job 👍👍👍

[@axiomloves21]

Those front breaks better become disc breaks soon lol. At 40mph they will melt. Trust me. I got two disc breaks on mine.