How To Replace 2004-2008 Ford F150 Pressure Power Steering Hose

[@HomeOwnerRepair]

Buy Power Steering Hose: amzn.to/3E0MHHn

[@markbrown3973]

Great video. I just changed both. Pressure and return. My 07 has no pressure sensor. I read the instructions about half way through. On mine the fitting on the pump is a quick disconnect. Should be able to pry between the nut and the square piece on line and it will pop out. I did it the way you did. My return was rusted through and stuck in the rack. I used a heat gun and finally got it out. 2 lines,5 hours out in the gravel. Getting too old for this chit. Lol

[@locknload9143]

Mines stuck also..So a heat gun worked for you did it?

[@HomeOwnerRepair]

Glad this helped you out.

[@chargeron3115]

I'm doing the timing job on my 09 f150 so I decided to change out the leaky ps high pressure line while I had easier access. Well, it's STILL a huge pain. I know the dealer wanted big money to replace it. Thanks for the video!

[@HomeOwnerRepair]

Hope the video helps you out. Thanks for watching!

[@SpoiledMilk11]

Some tips to make this job a lot lot lot easier from reading the forums is, remove the fan and fan Shroud it will give you an infinite amount more room, and in order to not have to cut an 18mm is to pull the pulley off. This video was helpful not a lot videos or forums on this, I was replacing my power steering pump when I bent the line and had to replace it

[@HomeOwnerRepair]

Thanks for watching! Don't forget to subscribe!

[@recrdholdr]

Better to make the wrench than to spend an hour pulling the pulley off and reinstalling it.

[@TheDivergentDrummer]

@@recrdholdr Pulley comes off in 30 seconds with a puller.

[@danielguerra5599]

@@TheDivergentDrummer Which puller, did you use?

[@howtodan1975]

Been looking for tips how to take this precious line that ford have designed which is nuts, you gave us hope to do it diy with out using a puller, thanks and godbless

[@HomeOwnerRepair]

Hope this helps you save some money.

[@Thewildterritories]

I replaced the return last year. Probably should have done both at the same time. Pressure line is pretty corroded and just started leaking today. Looks more “fun” than the return.

[@mick5740]

Great video guys. Iv got a 06 crew cab xlt. Trying to buy the part. They have alot of different parts. One says with switch port other no switch port etc

[@HomeOwnerRepair]

If you are not sure which one to get have the dealer run your VIN # and ask them for the OE part number so you can match it up. Hope this helps you out.

[@masonpugh3637]

Great video cut wrench works plus my got a skid plate nice job guys

[@HomeOwnerRepair]

Thank you for checking out this auto repair video. We try to provide the most detailed auto repair videos on KZbin. Have a great day!

[@CrowCreekOutdoors]

Practically everything on the 04-08 F150 is a pain in the ass to work on.

[@HomeOwnerRepair]

Hope our video are making this an easier process for you. Thanks for watching.

[@Fourandaquarter]

You can say that again. Possibly one of the most miserable rigs I've ever worked on. My '10 F150 fights me every step of the way.

[@jerrylamb6272]

I've had Chevys most of my life this is my second F150 your 100% correct every Fricken job I've had to do including the starter witch I've Done a lot of them Chevy always had 2 bolts then 2 nuts for the wires Ford has 3 bolts holding it on and of coarse the third one on top is a bitch I couldn't get my fat Hand up in their but anyway If your one of those guys that prefers to do his own work buy a Chevy or you'll spend hours doing jobs that used to take minutes to do.

[@jessewalker1770]

By far, the best way to replace the HP power steering line.

[@HomeOwnerRepair]

Thanks for watching

[@jflex835]

Great video! Thank you for taking the time to make it!😀

[@HomeOwnerRepair]

Glad it was helpful!

[@williemax21]

You guys are a real dream come true you know that

[@HomeOwnerRepair]

Thank you for checking out our auto repair video. Have a great day!

[@alanbarthelette7386]

The best video yet. Great job thank you

[@HomeOwnerRepair]

Glad you enjoyed it!

[@KillTheRemedy]

Trying to do this RIGHT now. I have an 18mm crows foot... buuut it is too small. What yr was this truck? Im on an 08. Ive got an 18 & 22. Guess im gonna hunt down a 19 and a 20... but i dont eve. Have wrenches that size to modify. Just tryna pull the pump and leave the line cus its still good. 😮‍💨

[@HomeOwnerRepair]

Thanks for watching

[@Ooze_yt]

Remove the pump with a pump pully puller

[@marbinbarrios5866]

you are correct! gotta buy/find sacrificial 18mm wrench

[@HomeOwnerRepair]

lol..Yeah was a pain doing this repair, but the wrench trick helped.

[@MF.199]

How long did it take to get the line back in? I have not tackled it yet! your video seems to be the best way without having to take the pully off

[@HomeOwnerRepair]

The entire job took a couple of hours.

[@locknload9143]

Question: Do you have the specs for the 18mm bolt.( Pump to valve body)..Also the 10mm hold down bolt. (valve body/ 2 lines). For the life of me, I cannot find the exact specs. I dont want to over tighten obviously. Best video yet Thanks! Thanks guys!

[@HomeOwnerRepair]

Unfortunately I do not. If you follow along with the video you should be okay. Hope the video helps you out.

[@locknload9143]

@@HomeOwnerRepair .. yeah no big deal I found them I had to replace the whole rack and pinion along with the lines. Lots of fun. Thanks anyways. Good video

[@canyon12alex]

Whenever I feel cocky in life, I watch your videos to remind me how dumb and useless I really am, lol

[@HomeOwnerRepair]

Thanks for watching

[@mattmgarza]

"It wasn't super crazy tight." I had the opposite experience. I can't get it to come off so I'm just cutting it off and replacing it while I replace the pump.

[@HomeOwnerRepair]

It's a tight spot I agree.

[@Ooze_yt]

How do I install the ine back to thr pump, I have the pully off i can't get it go in to where I can crank down on it

[@HomeOwnerRepair]

It was a pain but everything we tried or ran up against during our repair is in the video.

[@mick5740]

Great vid. Love thee accents ehhh Boouston??

[@HomeOwnerRepair]

lol..Thanks for checking our our auto repair video that shows you how to replace the steering hose on a Ford F150

[@williambellamy6197]

so i put a new high pressure line on my 05 about 7 yrs ago its leaking about a quart per year this was such a pain in the ass to change i will just live with the leak

[@HomeOwnerRepair]

I know..nothing is easy to work on. That's why Steve and I make these video to help you guys out.

[@ralphwhitaker8761]

I have a 2003 ford expedition, the line is broken inside of the fitting and the bolt around it is strip so I have no way to take it out, is there any hose strong enough that I can use over the old fitting to make a new line over the old one for the high pressure line, or do you have any suggest what can be done in such horrible situation? Thank you

[@HomeOwnerRepair]

Can you get a small pair of vise grips on the stripped bolt to turn it free? Not sure if you can get an easy out in that spot to remove the bolt.

[@ralphwhitaker8761]

@@HomeOwnerRepair nah there is no room at all, but I did try a small vise grip it goes in circle, I am going to try and weld another bolt on it and take it from there, if not I'll have to change the whole thing or take out the whole differential and try to cut it off, either way it's a lot of work, but thank God it happened in that kind of weather, not the cold weather which would be hell

[@chefserg1435]

I know this is an f150 but would you say this a similar fix for an 2005 ford 500?

[@HomeOwnerRepair]

No 100% sure how much time is required.

[@jongearhart1359]

The high pressure line is on the bottom of the pump ?

[@HomeOwnerRepair]

I believe it was.

[@kayd5250]

This process is nearly identical for replacing it on the F250 super duty as well.

[@HomeOwnerRepair]

Thank you for checking out this auto repair video. We try to provide the most detailed auto repair videos on KZbin. Have a great day!

[@BIGJDIRTY]

What is the line just below that one ? With the 10 mm bolt plate? At the 5 minute mark ?That’s the one that’s leaking on mine. You took out the 10mm bolt but only removed the top line. Forgive my ignorance. I don’t know the names and I’m in a pickle

[@HomeOwnerRepair]

It looks like it may have been the line in from the power steering reservoir.

[@diegobasstian3765]

What did you do to the 18mm?

[@potatosalad5355]

He... CUT (Sacrificeid) the 18mm to make it more SHORT to access to the bolt...! 11:59

[@HomeOwnerRepair]

Yeah, We had to cut down one of my dad's old wrenches to get it to fit in there.

[@Ezstreet327]

Couldnt you have cut the lines, pulled the pump. Replace the lines and re installed by fishing the lines back down. This seams more difficult than it needs to be

[@HomeOwnerRepair]

That may be another way to tackle the job. Thanks for checking us out!

[@tonycastaneda5371]

What year is the truck

[@HomeOwnerRepair]

We state this at the very beginning of the video.

[@CorbyCollins]

What's the name of that line with sensor

[@stevegriffin2626]

High pressure line

[@HomeOwnerRepair]

It should be called the high pressure line.

[@gsdtdeaux7]

The hose in your link is not the same as the one you used. It doesn’t have a sensor

[@HomeOwnerRepair]

I'll take a look at it...thanks

[@potatosalad5355]

He... CUT (Sacrificeid) the 18mm to make it more SHORT to access to the bolt...! 11:59

[@HomeOwnerRepair]

Yeah this was a pain, we had to modify one of my dad's old wrenched to sneak it in there.

[@IronAntOilpatch]

Please change the filter; it’s a sacrificial item. That makes no sense.

[@HomeOwnerRepair]

Thanks for checking us out and the added tip!

[@shivgan3g]

I thought f150 was easy

[@HomeOwnerRepair]

It wasn't too bad.