How to Install a Bath Tub

[@HomeRenoVisionDIY]

To watch all the videos in this project click this link. kzbin.info/www/bejne/sJq8gpSujrapb5Y And remember with playlists you can scroll through the videos using the arrows in the bottom left corner.

[@ignaciolanderos9726]

@Home RenoVision DIY i got an acrylic tub on a concrete floor... do you recommend setting this in a mortar bed?

[@mdrazaulkarim127]

বাস্তব বসানোর সঠিক উপায় বলে দিন

[@pl9742]

What's the name of the red tape?

[@dennismeyers2008]

Ok

[@azcoach5369]

Whats an avg cost to add a tub to an existing shower? Would you say 2k?

[@rawlsawh2804]

Beautiful, clean install. In my country Guyana 🇬🇾 a tub is a rare thing but it's wonderful to watch you work. Thank you. Cheers.

[@HomeRenoVisionDIY]

A nice tub is definitely a luxury in this world. Cheers!

[@ToPsHoTaBB6]

Better get a calabash and run under that zinc roof!!

[@jimkrk]

I have watched Jeff on a number of projects he has done, and as a hard core home renovator, i find his videos most helpful especially where new products and tech are concerned, keep up the great work

[@j-sgregoire50]

Great video - I would add that unless the full bottom of the tub is sitting flush on the floor, it would need to be installed seated in a bed of mortar. This method would pretty much guarantee no cracking. Unfortunately, I cut corners installing my acrylic tub and it started cracking a lot after a few years

[@r.joseph8911]

I can't wait to reno my bathroom. My tub is a real piece. Unlevel, rusting, freezing cold in Winter, etc. I hope to watch all your bathroom how-tos and get'er done!!!

[@HomeRenoVisionDIY]

Get er done, lol go get em Larry!

[@gjmartin01]

Great video - extremely helpful! I wasn't sure where to apply silicon or whether to use plumber's putty for a new drain and you covered both items perfectly! Absolutely love your videos by the way! I've remodeled two bathrooms now including one where I installed a full tile walk-in shower stall and you've been a big part of the whole process - thank-you for all the help!

[@89pils]

Did you end up using silicone or plumbers putty?

[@sentinelalerttowncrier7019]

I always put a ledger board along the inside wall to support the inside edge of the tub. A tub full of water and an adult will sag some if the inside edge is not supported from underneath. It is especially noticeable when you use tile and grout for your tub surround.

[@chrisgraham2904]

Depends on the tub manufacturer, but I think it's good insurance.

[@davidmurty9693]

I am a retired builder , if there is such a thing, I have to say you are very practical and informative I look forward to you other video's

[@CuddaBrown]

Where was this when i needed it about a year ago...great Reno Ninja skillz on this...

[@HomeRenoVisionDIY]

Sometimes I loose sleep at night because I can't help folks fast enough. The cross I must bear! Cheers Cudda Brown. How is it in Miami anyway?

[@CuddaBrown]

@@HomeRenoVisionDIY still hot..and hectic. You're doing sn awesome job bro.u help countless people all over the world everyday. You're indeed a true blessing to others and your family.

[@janicesmyth2183]

We love your channel! My grandkids have learned so much and now want to start their own reno companies!

[@sarahzamir757]

We used your Technics to instal bath tub and shower fixer . Thank you 🙏 you are amazing

[@pLaIrVaIdNoGx]

Jeff makes me feel safe.

[@RockChunker266]

I am getting ready to demo and upgrade my bathroom in my mobile home and this video was so beneficial for me. Not being a pro, I am learning so much from your videos. Thanks!!!

[@austincrosby9942]

Coming from a tile guy, I’m disappointed that you didn’t level the tub lol.

[@springer-qb4dv]

Thanks for the nice instructional video!. Only qualm I have about copper drain pipe is that they corrode. Major problems in old condos with old corroding copper drain pipes. And that flexible copper pipe looks like it's not going to last

[@DavidLee-ut6zn]

I agree with you on that. I had a rental property where my renter kept putting Draino in the drain and it destroyed the traps under the sinks and metal tub drains. It was a very expensive fix under that tub! Grrrrrrrr!

[@wills2262]

Awesome video, it has a this old house feel, but the depth and detail is way better. Keep up the great work!

[@HomeRenoVisionDIY]

Thank you. Cheers!

[@SchoolforHackers]

I deeply appreciate a good teacher. Thank you.

[@abebouhadir5020]

Thanks for all the precious info. One question, do we need to use any material to go under the tub so it is nice and snug against the floor? Someone recommended foam or sand... Thanks

[@MaMa-qh4dy]

If you ever need to remove the threaded tub strainer, good luck. The silicon on the threads and under the chrome flange will lock it on forever. Great video.

[@richardordonez8331]

I like your video production style. It's very condensed and polished. However, I wouldn't use the silicone sealant on the drain threads. You know how hard that's going to be to replace one day.

[@TheRealWattz]

When installing vinyl plank flooring do i set the tub in top of the underlayment or just in the subfloor?

[@bensb166]

@Home RenoVision What are your thoughts on adding a layer of cement under the tub before placing?

[@ryanwilson5643]

I'm installing a new tub this weekend but I haven't seen any of your videos where you use mud underneath. What kind of mud should I use and how do I apply it correctly?

[@beshoy19]

Thank you so much Jeff, I have transformed my house because of your videos. Good job as usual, I did everything, my next project is fabricating granite by myself.

[@branimal18]

Glad to see you recovered from the black eye

[@Sean-Aviation]

To those who rapidly hit the dislike button PLEASE think before you do so. people take their time to teach or show their trade secretes or even just want to share which means they give you something for free. If you disagree, OK just leave but don't discourage those who takes their time to make us great videos. If you have a better ideas OK, write them in the comment, share so we can all learn extra tip but avoid the dislike bottom in these type of videos that people share.

[@HomeRenoVisionDIY]

No worries Sean, I got big shoulders.

[@dreamingrightnow1174]

Yep. Think how much longer it takes him to do this job while the talks over his shoulder to the camera, and how the heck does he get somebody willing and able to jocky the camera in those tight spaces? Plus while he's doing all this stuff he's actually teaching his craft so any dummy can imagine it's all possible, and doing it all with such good humor and patience.

[@caturgito3926]

Mo p

[@christianpolytechnique7404]

I completely agree with you Sean.I love watching these videos,I learn so much and I love all the tips and tricks Jeff gives us.Years of experience that he has and as you say,he takes the time to explain it to us all,free information.Some people are not appreciative at all.Too bad for them.Keep it coming Home RenoVision,love watching your videos!

[@valentinasoubbotina2936]

SEAN! I A B S O L U T E L Y! AGREE w/YOU! YES, PEOPLE! AMERICAN SAING: -"IF YOU DON,T HAVE NOTHING TO SAY NICE!, JUST S I L E N T!" HAVE A CLASS, HUMANS! IT DOS NOT MATTER, IFYOU DON,T SEE PERSON, YOU CRITICIZE! EVERYTHING WE SAY, GOES TO CHRONIC ACASHY! AMERICA IN PREVIUS "DAYS" USE TO BE VERY POLLITE COUNTRY! W/PEOPLE, WHO SHOWES YOU, HOW TO FINDE PLACES...,HOW TO UNDERSTAND SM/TH..., WITH SMILE..., VERY FRIENDLY...! NO ONE LOCK THEY DOORS...! THINK ABOUT THIS! PEOPLE!, WHO HIT DISLIKE BOTTON! WE ALL HAVE TO BE HUMANS! WE ALL PARTS OF OUR PLANETERY FAMILY!

[@MrJacob50]

Good morning and thanks a million, I'm in the process of a new bathroom and your info has helped Big time. Thanks Jeff Bro, Jake and familia.

[@hkgonra]

Just got in a brand new Delta acrylic tub and a flyer staples to the installation packet said do NOT use silicone caulk with acrylic. They recommend DAP 3.0 and a couple other comparable bathroom caulks that do not contain silicone.

[@HomeRenoVisionDIY]

Then use what the manufacturer suggest. Cheers!

[@tykszeto]

Thanks for the great explanations... Was about to ask why silicone versus plumpers putty on the drain, but you answered right after! Great video! Cheers!

[@HomeRenoVisionDIY]

Cheers to you as well!

[@iamthemagazine1172]

the Best #youtubeteacher ❤ this guy renov is my favorite youtube 😊

[@congerscott6064]

Good video, trying to get back into plumbing and watching as many video's as i can, thanks 👍.

[@link9alink9a71]

These videos in youtube make all contractors busy I get so much call phone to fix the job that people try to learn from KZbin and save money to do it ohh yaaa. . ... everything in youtube easy 😄

[@dakotaevans7409]

Do you suggest using mortar under a bathtub?

[@gilbertvidana9709]

Nice Work!! Keeping it simple, no over kill. Thx

[@HomeRenoVisionDIY]

Simple rules. Cheers!

[@sellbythebell]

Jeff, love your videos. I've started to gut my bathroom and your video have been very helpful! I got to the drain/over flow line, and found the metal pipe had rusted away. The previous tub would flood underneath as the drain line did not connect to the drain hole. Now it is just a hole in the concrete floor. Not sure exactly what to do from here

[@Methodical2]

Is it recommended to use a bit of the silicone between the tub drain rubber gasket and the brass flange?

[@edisonorellana3515]

Wow the way you explain it . Thumbs up to the moon

[@yuchieh4638]

Hi Jeff, I saw you use silicone to seal the drain head. Is this a normal practice? I saw many others use plumber putty to prevent leaking. Now, I want to replace the drain head, but I broke the cross support inside the drain. I am wondering if my drain head was sealed by using silicone, will I break the AB pipe when using the drain remover? Is there anything I should pay attention when replacing the drain head? Thanks.

[@donaldsherman1]

Looks like the studs were planed down to accommodate the tub. Did you find the alcove like that, or did y’all do it?

[@CynsCorner]

What is that kit you used to screw the black plastic thing into the overflow. We have the type that uses a bar across, but what you used looked much better. Does the kit come with a bushing? Or would a whole different overflow unit need to be purchased?

[@simmitysam1397]

you dont use mortar, under the tub? or even foam? whats your thoughts about that?

[@MIRUSTICS]

Good Videos on your channel. this one has given me some good confidence in refinishing my kids bathrooms.

[@Zerathorn]

Hey Jeff, did your brass kit come with the pvc to brass adapter? Also, could you share the make and model of the brass kit you used in this video? Isn't it great that your 2 yo video is still teaching? Thanks

[@DitNg516]

is it necessary to put mortar underneath to support the tub?

[@JohnSmith-fh1rx]

Nice job and very professional

[@teressasepka1261]

My husband enjoys your videos immensely. He loves to learn new things. Unfortunately they frequently require more toys. I would be particularly interested if in the future you could demonstrate how not only in to install a whirlpool tub but also tile the perimeter and use the new Schlueter products that you have been speaking of. Keep up the wonderful work you’re giving my retired husband something to do.

[@DRT2OILFM]

Do you need to install a support beam across the back side of the tub to rest on against the wall?

[@HomeRenoVisionDIY]

depends on the manufacturer. Cheers!

[@sarahdavis5016]

That is a great video. I recently had a small leak from underneath my bathtub. I tried putting some new plumbers putty on the drain, but while screwing it back on, I managed to cross thread it. The pipe was plastic and not metal like yours in this video. What should I do ? Can I fix this on my own? Is there a way to fix a cross threaded plastic pipe? Thank you!

[@HomeRenoVisionDIY]

Hi Sarah, the only Option you have is to apply silicone to the drain and the threaded pipe and install cross threaded and hope the silicone seals it. otherwise you need to open a hole in your ceiling and install a new fitting to receive the drain. Cheers!

[@pfish23]

Love your content. In fact I am helping a friend put in some sweat equity in a home he recently purchased. Would love to see some content on roofing systems. metal roof, shingles and the like.

[@HomeRenoVisionDIY]

this spring. Cheers!

[@knowledgeseekerr]

The overflow drain kit is like almost $200 bucks! You can basically get Overflow drain kits for half or even 3/4 of that price! were did you buy yours? would like a link if you could please

[@tandaduguay3195]

Jeff I am hoping you cam guide me. I am redoing my bath and tile and ran into difficulties with taping and cementing the cement board joints. The tape was not sticking.

[@JcP3737]

Im a plumber from texas. I like seeing how different parts of the country do their work ... this comment is the start of this video First edit... he is talking about a second floor application 2nd edit... i think just going abs all the way without that funky brass and copper with glue joints would be better 3rd edit... ya i only like compression joints in cabinets that you can access 4th edit... i set all my tubs with a mortar bed to "make it soild"

[@chrisgraham2904]

If your from Texas, Jeff isn't operating from a different part of the country...he's in Ottawa, Canada. Yes...this is an installation over joists which could be a second floor or a first floor over a basement or crawlspace. Canadian building code doesn't require an access panel or shut-off valves for a tub and shower installation, but it's always recommended if they can be provided. The mortar bed provides stability, especially preventing any flex from acrylic tubs and it aids to eliminate that hollow sound when showering.

[@GnizakJ]

I have an acrylic drop in tub that's sprayed with fiberglass and has the type of feet that screw up and down to level. It has one in each corner and one in the middle. The instructions tell you basically nothing and I cant find any info anywhere else online about this tub i got from home depot. Do i just install it the way it is or do i need to put something underneath the tub like a mortar or sand bed?

[@benfeld4058]

Thanks for the video Jeff! Could you tell me what the brand of the drain kit is? The closest I can find is from Kohler around $160 at Lowes. Thanks!

[@andrewjforgino]

i'm very interested myself

[@_dsb]

How did you adjust the height of the drain pipe for a perfect fit with tub outlet?

[@JasonSells100]

Hey Jeff - love the videos always a pleasure learning from you. What are your thoughts on setting an acrylic tub on a bed of mortar. My brother is a pretty big guy and cracked the last tub he had. He’s not looking to spend a lot on a reinforced tub. Any other ideas to transfer the weight? Thanks again Jeff

[@HomeRenoVisionDIY]

it works. just make sure to do a dry run on the tub install first so you know it is in the right place , or be able to connect the drain from underneath. Cheer !

[@aconsideration]

So, I have a brass valve and iron pipes. Can I join them? Can I use some of that white tape in the threads and be good? Love the videos :) thank you for sharing.

[@masonlovesroblox]

Why is ABS plastic plumbing in Canada and PVC plastic in the USA? Is there an advantage of using one over the other?

[@greenfrogy]

I recall you mention a Canadian bath tub company you recommend. What is the brand again and what material is the bath tub made of ?

[@akhilbose1712]

Hey Jeff, just bought the the Tuscon. Will install the tub next week. I will use the redgard as suggest in one of your waterproofing videos with the mold proof drywall in the shower area. Can you suggest a floor preparation video that I can follow. I will be using a porcelain tile. Thanks

[@mnm1067]

Does a wet bed or mortar have to be used when installing a bathtub?

[@dinhnguyen9056]

Same question. No mortar bed needed for acrylic bathtub?

[@irish89055]

@@dinhnguyen9056 apparently not with those wooden feet..

[@inikobmore30]

This was great 👍 I'm doing the same thing I'm ready to put up the vapor will which I didn't know about. Thanks

[@fabiangarcia2411]

Great video, thanks for showing how it’s done. Doesn’t seem to hard !

[@craighuckin2302]

So I have installed tubs before but I’m wondering have u ever tried the maxx utile system I’m partially disabled and want a great bathroom but can’t tile and want to be able to do it myself

[@lordgarth1]

Do many people just go with a large walk in shower now? I’m trying to decide on ripping out the old tub and building a car wash spray shower or going with a garden tub.

[@HomeRenoVisionDIY]

That depends on if your home is better suited to an aging family or a young one. Cheers!

[@Haider.sharifi]

Curious- a lot of other folks go into some depth on leveling the tub. Did you have to level this one at all? If you have to shim behind is it pretty easy to get in behind the tub?

[@HomeRenoVisionDIY]

leveling the tub may be necessary if you have a flat top that allows water to flow over the edge. this design is beveled and keeps the water diverted back into itself up to a 1degree slope. not usually necessary.

[@josephrisner3473]

Excellant video.Crystal clear O.J.T. Thankyou. Is it advantageous to use an adhesive where the 4 points meet the floor?

[@natanfatakhov6161]

As a DIY I learned so much with you.Thank you.Ad meah ve asrim.

[@andrewcarr2431]

cannot wait for the next part, looking forward to your finished tub surround

[@HomeRenoVisionDIY]

See you Saturday then. Cheers!

[@westw00d08]

Have yet to see the video of how you installed the tub surround and covered the flanges with drywall to make it look neat. Thanks for all the other video on bathroom renovating. W Sawyer

[@guzman9011]

Just ordered a 21” acrylic tub. This helped me out a lot thanks. Also I’m the 3000th thumbs up!

[@felixfernandez442]

I really learn a lot thanks you

[@mattl1758]

Lol! First off thank you second: I’m watching this video because my tub did crack! It was installed without support. Thx

[@MrDW-ei1fe]

That’s more of a “buying cheap shit” than an improper installation. I’ve installed cheap stuff and I’ve installed a bit more expensive but good quality stuff. The difference is huge.

[@johnhandcock3242]

So, cement board sits on top of the tile flange? Would this be the case with a shower base as well?

[@bennemets4471]

Yes. I just installed a shower base. However, I used a drywall with a waterproof membrane (Densshield). I left about a half inch gap between the flange and the bottom of the drywall

[@153Rocko]

I enjoy your videos. Very detailed and helps me know everything about my project.

[@youngtimer7531]

I installed an acrylic tub. Works great but the front bottom came loose from the bead of clear caulk that I secured it with for 2 reasons. To keep water from under the tub and to stationery the front. any suggestions?

[@chrisgraham2904]

Remove the existing caulking, fill the tub with water and apply a new bead of caulking.

[@lucasjohnson5871]

Tub install was complete and flooring put in, but after bathing for the first time, the side of the tub has pulled away from the grout and tile. It seems to have moved inward. Was it installed incorrectly? How can i fix it to keep it from shifting more? Can i just grout more? What is the best fix?

[@HomeRenoVisionDIY]

fill the tub with water and then use silicone to seal the edge.Let dry overnight before draining tub Cheers!

[@RealGame101]

This is my dude. He’s pretty good at this stuff. And I may have to special order that drain kit. Awesome

[@HomeRenoVisionDIY]

It comes in mighty handy for many situations. Cheers!

[@ericevans9733]

@@HomeRenoVisionDIY Link to drain kit?

[@j0yfulblessings]

Totally unrelated question, sorry... but we have a heavily painted popcorn ceiling. (From the 50's) Do you suggest removing it or just drywalling overtop? Tips?

[@HomeRenoVisionDIY]

I would install a new drywall ceiling over the whole thing since you likely have high levels of asbestos in that mix. Cheers! Use laminating screws.

[@redhoward11]

I've been remodeling bathrooms for 15 yrs, you got most of it right. You didn't use a mortar bed on that acrylic tub. You should have installed the framing support for doors after the tub was in, your viewers definitely need to know that part. You conveniently left out footage of actually lifting and setting the tub. You can use an oscillating tool or angle grinder to radius the corners of the skirt to ease installation, an extra inch goes a mile and it will protect the corners. Oh and no you will never actually see the corners of any tub skirt after finish work is completed. You also failed to point out that you had to remove sheetrock and outside corner bead to set it. What if your viewers are not working near an outside corner? You could have raised the subfloor and overlapped the tile, rather than cut the tile floor back. We never got the chance to see a level set on the tub rails. Does the subfloor need to be patched back in to avoid one of the feet being left unsupported or if on a crawl space sealed to prevent pests and cold air from entering? How do you leak test the slip joint drain assembly? Guess I should stop there because people are going to call me an asshole, but I've done this thousands of times and made alot of mistakes along the way.

[@jindo333333]

wow. two thumbs up!👍👍 what a great video.

[@voiceofantonio1029]

We gotta get this one to a million views ❗️💪🏽

[@neflood]

Putting a new tub in my house. Fixing the house up to sell. I live in Portland Oregon USA. Which tub brand do you recommend for here in the states?

[@1zebula1]

At 11:33 - “the other thing we have to do is find out how far off the ground the drain needs to be”... but then the video cuts to it already done. How did you do it? Is it in another video? I’m in the middle of the exact Reno. Inspired by you, bought the Tucson tub from Mirolin. Got the OS&B drain and over flow, picking up tomorrow. Also the ABS piece, that you bought separately and then connect it into the OB&S?

[@bigsun4212]

Where to buy this flexible brass drain (waste and overflow?) kit? Or what's the name of the product???

[@clarajulio2024]

So thinset to support the bottom of the tub?

[@jimmyparaha925]

can i use hot water from the house to a cabin shower if i t piece off the hot water cylinder from the house or should i get a new hot water cylinder

[@jimmyparaha925]

the cabin is very close to the houses hot water cylinder

[@HomeRenoVisionDIY]

that depends on where you live. Check with the local building office to confirm.

[@jimmyparaha925]

its confirmed they said its fine do you recomend using a seperate one for the 2 bedroom cottage

[@thomsmucker6187]

Do you recommend putting window/door spray foam under the tub for support? My tub at my house feels flimsy, the floor flexes a little in some spots.

[@HomeRenoVisionDIY]

not on a mirolin tub with a reinforced plywood base with fiberglass pray and post legs I don't. If you have a tub that needs help use sand mix.

[@kennethhadden934]

Hey Jeff I’m wanting to put in a drop in tub. They say I got to use a cement or mortar bed under it. Is this true if so do you have a video doing this?

[@paulestridge8734]

Yes, you must place the tub in mortar to support it. You don’t want the tub hanging by the flange that goes around the tub or it will crack. Don’t try to cut corners!

[@MrSuperJeffer]

I noticed that you didn't put a mortar bed under the feet... is it not required with that style of tub?

[@antoinetony6648]

where is a link for the tub you used?

[@ralph9987]

Do you also have an install video for a tub on a concrete slab floor pls?

[@frailpel]

Is it important to level or make sure the tub is leveled before screwing it in, or does the slope of the tube interior compensate for not leveling?

[@HomeRenoVisionDIY]

level is nice but often hard to achieve. if you want level then level the floor before installing.

[@frailpel]

Home RenoVision DIY sounds good, thanks!!!

[@chrisgraham2904]

You want the rim or tile flange of the tub to be level to aid a clean and level tile install. Also make sure the front apron sits level on the floor. Finally, most manufacturers design the tub base with a slight slope to the drain so that all the water drains and doesn't leave a puddle. If a cup of water, or a golf ball rolls to the drain, your good.

[@subratakumardas3178]

Perfect installation technique of bathtub.

[@dailodai9586]

what about mortar? is this tub not necessary for it?

[@wambklyn]

Any reason you are using brass instead of PVC? Would you still use brass drain kit if you had not come across flex situation (like relocating plumbing)?

[@itsmee9779]

HEYA JEFF.... Where is the next part of this mkeover ? Maybe if the video shows 1 of 3 then we know which part continues from which session. EXCELLENT WORK !! GREAT TUTORIALS !!

[@HomeRenoVisionDIY]

we are coming back to the bathroom this weekend and will have the rest of the 9 part series by the end of the month. Cheers!

[@stephenbanks2939]

Do you always have to replace the plumbing or can the pipes already in place be reused?

[@BPLmarCH]

It's all depending on the tub you're putting in. In this case, he is installing a 32 inch wide tub into a place where there was a 30" tub.

[@troygodfrey6482]

If your going through all the work to take out the tub you might as well do it right and replace all plumbing heading up to the shower head and the drain. You can use the same but it’s lazy and won’t last

[@sleddy01]

Just a question because I don't know but is code OK with those plastic compression fittings for the tub drain not accessible?

[@HomeRenoVisionDIY]

depends on the area you live!

[@pbgd3]

Mirolan isn't available in the US any specific tubs people have used to good outcomes?

[@DavidLee-ut6zn]

Not promoting one brand over another, but take a look at Laurel Mountain. They have a wide variety of models and sizes. They answer the phone for questions, but sell exclusive thru Lowes. They also have 66" and 72" tubs which is really nice versus those 60".

[@Juan1976ification]

Hi Jeff, thanks for sharing your time and knowledge, do you have a video about how to fix or update 1994 mobile home shower hot and cold water line or how to do the transition from gray pex pipe to white pex pipe or how to replace the old copper elbows any idea please thanks