Honda 300 REBUILD Episode #22. Piston removal and cylinder install!

[@masonsebrnn3297]

I normally put the piston in the cylinder first with ring orientation correct. Then install on engine

[@tonylynn191]

When it comes to 300’s I always look for you before anybody else 😅

[@PowerModzOfficial]

Thanks!

[@2StrokeSmoke544]

HES BACKKKK

[@davefarnsworth9022]

How can I go about adding a 300 head on a 250 motor Honda

[@codyswilley]

I call them bikes too because you set on them like a bike. But they're also quads because they have 4 wheels, but also bikes because they have handlebars, not like a sxs where those has steering wheels

[@DawsonBordelon]

We call them bikes as well here in the boot (Louisiana)

[@call912now]

What are you manufacturing in the back ground?

[@ryandooleymusic6744]

Louie! You're alive!

[@PowerModzOfficial]

Oh ya still kickin

[@jasongodin7165]

Never place new rings is a warn out cylinder, The rings with age wear the cylinder in an egg shape , best to oversize

[@trappingtheoutdoors897]

Do y’all still have a website

[@davefarnsworth9022]

Can it be done can you put a 300 head on a 250 motor on a Honda Big Red

[@captaindeadpool1640]

I cant get the wrist pin out i hit it with heat and tried hammering it out and nothing i am now trying to drill it out with a unibit it moves on the crank shaft its just siezed to the piston . Should i heat the top of the piston and how long? Also it barely moves right to left maybe .002 of a filler gage is that okay? What would you do to get the wrist pin out?

[@MatthewDespino]

Did you remove the wrist pin retainers first???

[@bregott605]

been a while, missed your videos

[@connersnow298]

Nice vid

[@codyroger9581]

Hope everything is alright, it’s been a long time.

[@PowerModzOfficial]

Ya all is good - my usual spring rest...

[@hurstshiftin9873]

Mine runs fine lots compression but when i put it in gear and put the throttle on it developes a rattling knock thinking wrist pin bearing is shot

[@captaindeadpool1640]

What wrist pin bearing?

[@hurstshiftin9873]

​@@captaindeadpool1640was thinking needle bearing in center of piston pin.

[@darrellroeters4951]

Did you hone cylinder? The black gloves don’t show the work.

[@PowerModzOfficial]

Yes i did

[@cplpinker]

Good to see you again Louis. Ah Open Hart Surgeon now "A"?

[@PowerModzOfficial]

LOL, ya working on it - just finished my law degree and off shore sailing certification - and lunar landing license.

[@cplpinker]

@@PowerModzOfficial I got my Degree in Lazy. only took me a few weeks.

[@panic-revv85]

That much work why use a cheap piston?

[@haydenabing9774]

What oil were you using one the piston and cylinder

[@PowerModzOfficial]

just some engine oil

[@haydenabing9774]

@@PowerModzOfficial do you know the brand becuase im doing the exact same thing with my 300 and I’m knew to it and takes notes from your videos

[@user-mb8kz2hz2w]

@@haydenabing9774it probably doesn’t matter maybe just some generic 10w-40

[@Megadeath39]

Piston ring end gap?

[@PowerModzOfficial]

yes its in another video

[@Megadeath39]

Right on. Loving the old stuff. Weve got a 300 fourtrax as well.

[@hadoonenamnam1255]

ممكن تكلفت شراء وشحن الى عراق

[@hunterfreeman4336]

Garbage, i see you had to take off your little mechanic gloves to set the rings, and it still took you 3 shots to get them in the cylinder. Damn.

[@ramonapool619]

Been a lot easier with out the gloves.

[@PowerModzOfficial]

Ya, but this way I get to live a bit longer so it'll work out in the end

[@braptasticfilms3791]

Lame, need more content in videos

[@PowerModzOfficial]

Cant have content without a running machine....

[@braptasticfilms3791]

Michael Knight just implying that he make longer videos as it would be more interesting, I did not claim to know it all just keep on with whatever you are doing bud lmao