Honda Accord 2013 2017 Valve Cover Gasket Replaced

[@TheLarousse89]

I'm not going to lie I love how you mentally keep track of what's going on and then lay it out with some Italian handspeak. I'm 1:56 in and you show the direction of the harness and then the cover that you are referencing. I need to order the parts. I appreciate showing what you need before you get started.

[@RBTheMechanic]

I don’t see what I show at 1:56

[@TheLarousse89]

@@RBTheMechanic Just when you use your hand to show the direction of the coils, and then the cover and the harness. Specific start point is 1:43. It's just helpful that you break down the direction of things prior to even getting into the engine. I'll be doing this in my garage this week following your guide. And your other guide for the serpentine belt in a few weeks after that. Appreciate all the uploads.

[@laviebanale]

⁠ I just finished doing the valve cover gasket on my Honda. The video was abt 90% the same bc my car is a CRV. The video helped a lot. 🤝

[@RBTheMechanic]

Nice yup it’s same same

[@nonnegotiable347]

Just did this on my 2013! Took me a few hours but got the job done!! Appreciate you bro!!

[@RBTheMechanic]

Good job!!!

[@andyp9747]

Thanks dude. Bummer about the broken hose at the end in your video, you were so close. I'll be doing this job on my 2014 Honda Accord Sport where I see leaking oil residue along the gap of the valve cover. KZbin rocks!

[@RBTheMechanic]

Yeah thank bro !!! Best do it urself

[@deebocj]

I might do mine as well. 85,000 miles.

[@RBTheMechanic]

@@deebocj yup do it

[@kennylavay8492]

good video only thing i would have done was oil the new spark plug tube gaskets with some oil to make it easier to slide over the tubes. good educational video nice job.

[@陳櫻仁-r7y]

Hello, I’m from Taiwan, thank you very much for taking the time to make a video I just did my by watching you video you are awesome wonderful thank you and God bless you!

[@calimilk1113]

Thanks bro !! Just did my wife's honda accord sport. The hardest part was the pinche little wire clip that's in upper corner attached to the valve cover , no room to unhinged the clip lmfao!!

[@RBTheMechanic]

Cool good job!

[@kiwi_commander]

Awesome video, helped me replace the valve cover gasket on my wife's 2015 CRV

[@RBTheMechanic]

Nice glad video was help

[@calimilk1113]

Thanks big dog, I've done this job several times on older Hondas. But I have my wife's 2013 to do this weekend never done the newer ones. After watching this no problemo!!!!

[@TheGuyJose]

Thanks for this video man. I'm going to try this in the next week or two. I just need to have the tools ready and a closed space . I don't want anything getting inside of it if I do it outside...

[@FastEddy5]

You forgot to put the Honda Bond / silicone in each corner of the metal to gasket mating areas. You know where you scraped it off the first time. There is also a torque and pattern procedure that Honda recommends for this valve cover as well that you didn't go over.

[@RBTheMechanic]

Yeah I think we did put somthing there I pay very close attention to that section since 2009

[@ralphpaez3723]

This is so important to do and cannot be missed. I replaced mine and in a few months it was leaking again for not following this recommendation.

[@jh3036]

Your videos are outstanding! Thanks for always showing detailed, step-by-step instructions.

[@RBTheMechanic]

I try my best thank you! My up comming videos will be more detailed with part number price cost and torque specs

[@monteriuslewis1017]

@@RBTheMechanic where did you get the set from?

[@RBTheMechanic]

@@monteriuslewis1017 dealer

[@monteriuslewis1017]

@@RBTheMechanic man thanks for the quick reply but my dealer is saying that Honda don’t sell the spark plug seals at all

[@RBTheMechanic]

@@monteriuslewis1017 no I got these from my local honda parts department search it on eBay or Amazon but why don’t u look to see if it’s dry in the bores those screws can be jammed don’t even touch u might end up replacing the whole valve cover rather just do the gasket

[@rolandfaczan1722]

Great step by step video. I have to do it on may Accord and when I do, your video will be playing next to me. Thank you!

[@RBTheMechanic]

Roland Faczan cool take you time clean it well should be easy and simple job

[@mhiztazuwaomo3821]

You doing a good job and I like the way you explain the process

[@RBTheMechanic]

Thank you

[@jayr7014]

Nice job RB im about to do the same around noon on my son's honda

[@miguelsantarosa5123]

Perfect steps thank you, you saved me some money.

[@RBTheMechanic]

MIguel SantaRosa no problem please subscribe also subscribe to my other channel here’s a link

[@RBTheMechanic]

kobe Bryant forget what u charged my friend lol but good mechanic decent price on labor for this should $190 and gasket u can pick up from dealer $70 so total should be around $260 fair price for Thais job

[@xwasx08]

@@RBTheMechanic Hilarious. You asshat. Honda charges 150 labor included.

[@renem8130]

@@xwasx08 Honda is charging me $350. that's why i'm looking this up

[@MrRondeezzee]

I have a 2013 and your video just saved me 600 bucks.....

[@RBTheMechanic]

Ron deezzee nice job please subscribe also subscribe to my other channel here is a link kzbin.info/door/vqsPzqAZfVv_gjBYUFqNdg

[@k9casablankino845]

Great video! I’d suggest using a plastic scraper rather than metal blade.

[@RBTheMechanic]

As long as ur doing ur sadly ur fine

[@robinbrewer4099]

Really enjoyed your video, you explained everything very well.

[@pall5114]

another great video. I have a 2014 3.5 V6 Accord with 83k miles, which needs a valve gasket per the dealer. Is that a more difficult job? How many hours is that job? Thanks

[@RBTheMechanic]

This is very easy !! 40 minutes maxxx and take ur time cleaning

[@pall5114]

@@RBTheMechanic Thank you!

[@finn1355]

What was your torque sequence. What is the torque? Did you use a torque wrench ?

[@RBTheMechanic]

Yes I usully go from vent out cris cross

[@juanruvalcaba1823]

How many miles did you replace the gasket?

[@flacojacobo5672]

Thank you very much for taking the time to make a video I just did my by watching you video you are awesome wonderful thank you and God bless you👍

[@RBTheMechanic]

Good job!

[@tamourali8320]

@RB mechanic is it necessary to put on glue beneath the gasket

[@RBTheMechanic]

Yes that’s where the gasket might but meet propper cus of the side timing cover and engine block it’s need but silicon on those 2 spots

[@JakeOfAllTrades03]

Appreciate you taking the time! Question for you: I’ve seen other vids on this that apply gasket maker to the 4 corners where you had scraped the silicon off. I noticed you didn’t apply the extra gasket maker/silicon before reinstalling. Is it necessary? TIA

[@RBTheMechanic]

I think I did I always do maybe I didn’t mention it in the video but yes apply it

[@JakeOfAllTrades03]

@@RBTheMechanic thanks!

[@RBTheMechanic]

@@JakeOfAllTrades03 welcome

[@abubakarisadiqueibrahim481]

I like how cute the impact wrench is

[@RBTheMechanic]

Haha when I first got it I didn’t even use it just babbied it

[@tonylam4632]

Thanks for putting the time out for this diy. Wanted to know my car about 100k, what should I also change while I’m at it? Thanks in advance.

[@RBTheMechanic]

Change the spark plugs pcv valve and do complete gasket for the valve with center spark plug bore gromets that’s about it

[@tonylam4632]

@@RBTheMechanic thanks, btw which spark plugs should I go with? Dealer or specific ones?

[@RBTheMechanic]

@@tonylam4632 so far I have only put dealers spark plugs but NGK laser iridium are good or denso

[@henrybixler3321]

I really appreciate the videos! How long should I wait to turn on the engine after replacing the gasket?

[@RBTheMechanic]

Soon as ur done double check ur work and u can start it immediately

[@henrybixler3321]

@@RBTheMechanicThank you!

[@crisco431]

Thank you hermano great video step by step 👏🏽👏🏽👏🏽👏🏽

[@RBTheMechanic]

Yup thank u

[@bee2333]

Great job. How much did this job cost without parts

[@RBTheMechanic]

Well I charged the customer $190 labor and offered to do spark plugs in it with the job

[@sharkyy707]

What if a whole bunch of lights turn on lole the tpms light nd eps amd vsa manlfunction lamp helpp plz !!

[@jeffycortez3533]

Did you remove all the oil first

[@criticallycrunchy1782]

Oil sits at the bottom of your oil pan until you start your engine up.

[@lji2000]

@RB The Mechanic The adaptor for the cable that broke at the 48:00 min mark - can you share the details on this adaptor please?

[@RBTheMechanic]

Oh niceee u watched till end. Anyways here’s a link off amazon but it could be wrong so just go to pepboys or autozone they should have a kit u can check it out tho 18Pcs Windshield Wiper Hose Connectors,BUENNUS 2-Way I Type,3-Way T Type,3-Way Y Type Windshield Hose Connector Kit,Black Plastic Water Hose Connector Splitter for Universal Car Washer Nozzles www.amazon.com/dp/B07V3VGBTR/ref=cm_sw_r_cp_api_i_ZQ5RENCPJNDXKBAX3B3H

[@finn1355]

Did you ever find the lost bolt ??

[@RBTheMechanic]

Prolly did this is old video but I never leave it unfinished

[@MrBMWF30]

Great video, but now all check lights are on, did battery reconnect, came on again after 1 hour. How to fix?

[@RBTheMechanic]

Scan the car to see the code for issue

[@finn1355]

I am curious. Where is the CAMSHAFT POSITION SENSORS AT ????

[@RBTheMechanic]

I will make video on that this week

[@ocean694]

Why the head gasket needs to be replaced so soon on these Hondas ?

[@cmserafico4396]

Do I really need to change the grommets? Or can I still use the old ones? Thank you, great video. I subscribed.

[@RBTheMechanic]

If u don’t got oil in the spark plug boars then u can leave it alone or I would just change then since the cover is off

[@aloticbeast8094]

Nice video 👍 how much you think it’s fair for this service to pay for the labor in 2023?

[@RBTheMechanic]

Do it nice propperly and do the grommets also $parts and labor 280

[@aloticbeast8094]

@@RBTheMechanic thanks, it should be same price for a Honda pilot as well right?

[@RBTheMechanic]

@@aloticbeast8094 nope that’s v6 lot more part and labor

[@eddie-gomez9154]

Great video and information. I wanted to ask, once the gasket is replaced, how many more worry free miles should we expect from it before it goes bad again? Thanks..

[@RBTheMechanic]

Like 50-60k

[@eddie-gomez9154]

@@RBTheMechanic cool. Thank you!.

[@finn1355]

After the rag cleaning and razor blade scraping, vacuuming out the valve cover / camshaft engine bay area would be nice.

[@RBTheMechanic]

Yup clean would make a tip top job

[@kimjohnson2825]

Great Video! I will do this next weekend, what are the torque specs for the valve cover bolts please?

[@RBTheMechanic]

Kim Johnson I have to check what’s the spec what’s the year make and model of ur honda

[@kimjohnson2825]

@@RBTheMechanic 2013 , but I found it , 7 lbs. thanks for you great video! I change the gasket yesterday and did it in about 3 hours. I would never make a fast mechanic lol. Thanks for saving me some money

[@RBTheMechanic]

Kim Johnson yeah sorry I have been sick. That’s must be the spec it’s very Lil which is normal please subscribe also subscribe to my other channel here’s a link kzbin.info/door/vqsPzqAZfVv_gjBYUFqNdg

[@cameronpuccini7373]

Kim Johnson just to confirm that its 7 ft/lbs for every single bolt ?

[@avi9th256]

@@cameronpuccini7373 yes it is.

[@GuynelSaintVal]

where does the valve assembly spool and vtc oil control located on this honda accord sport model?

[@RBTheMechanic]

I have to check

[@kcthewun1009]

what was the torque specs for the bolts you tighten them up off camera and didnt provide the specs

[@RBTheMechanic]

7fl lb I tightened it twice one the car was hot so the seal can warm up and be more smoother

[@djflash7503]

Don’t have to unplug the Oxygen sensor . Just unsnap it from the cover.

[@money_mitch22]

What's the torque spec not sure if it was mentioned in video?

[@RBTheMechanic]

16ftlb

[@finn1355]

Using a plastic scraper is better than using a steel razor blade. Less chance to damage the aluminum.

[@RBTheMechanic]

I will look in to that

[@feliciarichmond5708]

If after following this video, my car engine light came on; what do you think may be the cause?

[@RBTheMechanic]

Double check ur work… check all the connectors and pipes also u can scan the car and it will give u code to let u know what the issue is

[@anthonychappell4746]

Did you remove the engine oil first?

[@RBTheMechanic]

No oil resides down below

[@domingofigueroa7884]

Great details step by step

[@Randizzl3]

How many miles are on this car? I have free full synth oil changes and my cams and internals look nothing like this.

[@RBTheMechanic]

I don’t remember but u see 100k

[@Randizzl3]

@@RBTheMechanicthank you, appreciate you.

[@shop22600]

Best video ever step by step. The parts, 12030-5A2-A01 is compatible with Honda Accord 2016 LX 4 doors? Thank you.

[@RBTheMechanic]

James Lee not sure but you can find out from dealer but I think they are same

[@jylee9542]

Dealer say not but I guess same. Is it same engine 2013~2017? And how many long rubber gasket in oem package?

[@RBTheMechanic]

James Lee well bro buy it from dealer it’s like $70 or less

[@LOPEZ-bj5sm]

What’s the torque expects on the head gasket?

[@RBTheMechanic]

Head gasket? Or calve Cover

[@shop22600]

Hi What kind of silicon use on the cover and body? Can you link the sites that sell Amazon and Walmart sites for purchase?

[@RBTheMechanic]

Sorry I don’t have link but u can purchase it from autozone just regular silicon

[@dariovillacorta7584]

Hello I have a 2015 Honda Accord sport, it’s a 2.4L I4, I wanna do this at home but what’s the torque spec for the bolts for the valve cover?

[@RBTheMechanic]

It 7ft lb

[@fishmanhype6304]

I just did the 2017 sport. It doesn't use any of the spark plug grommets at all.

[@RBTheMechanic]

Well it dose have it they r screwed in

[@3232myke]

Great video bro nice job when I do mine, your video will b playin rght next to me . Where did you get the adapters from

[@calimilk1113]

What kind of silicone you use?

[@BXHiram]

So no sealant is necessary? Only a little silicone to hold the gasket? Great vid btw... also is it necessary to change the gromits when doing this?

[@RBTheMechanic]

Hiram Asencio no u don’t need sealer just use few taps to hold the seal also do put lil bit silicon where I show small pieces on the head that I used blade to scrap off

[@baims8367]

BIG JOB. 😂. 10-10mm bolts real big job. This car a 10 ur old could maintain .. well engineered for ease of maintaining!

[@RBTheMechanic]

Ok still takes a skill

[@theobserver9565]

Our 2019 crv 2.4 liter with 15000 miles has had the valve cover gasket replaced because of oil seepage at the Honda Dealership. Oils is still leaking around the gasket in the front and left side. Going to take it back tomorrow. Are there any other possibilities as to why there is oil getting by the gasket besides a bad gasket or bad install? Can the the valve cover itself be bad?

[@RBTheMechanic]

It could be they didn’t clean or it’s leaking again got pinched bad installation I did one few months back idk why it leaked gonna warranty the guy

[@theobserver9565]

@@RBTheMechanic Could one of the mating surfaces be bad IE: not flat?

[@RBTheMechanic]

@@theobserver9565 it could be anything gasket didn’t sit propperly or pinched have cut uneven if u take it apart don’t even sweat the old one throw in new gasket

[@albanbnushj420]

Good video but next time be more prepared with your tools lol, and also this one will leak again you forgot to put rtv in corners but good video

[@RBTheMechanic]

Nope it’s been good ever since

[@stephaniemillan9553]

Do you have videos on how to change a oil pressure switch on a 2013 Honda Accord?

[@RBTheMechanic]

Sorry I don’t have it but I can give u instruction if u like

[@stephaniemillan9553]

@@RBTheMechanic that would be great! Thank you!

[@edhowardmobilegaming3818]

When we can drive the car after replacing the valve gasket?

[@RBTheMechanic]

If u want to make the bet if u out some silicon or honda bond on the sides give it good 2 hours so it can dry up

[@edhowardmobilegaming3818]

@@RBTheMechanic so is better star engine the day after replacing right?

[@RBTheMechanic]

@@edhowardmobilegaming3818 not a day later just give it good hour or 2

[@edhowardmobilegaming3818]

@@RBTheMechanic thanks for the information and always like your videos and keep up the good work 👍

[@RBTheMechanic]

@@edhowardmobilegaming3818 thank u!!

[@sicksol367]

Brother what is the torque specs for 2014 Honda accord sport I’m doing my RN please help!!!!!

[@RBTheMechanic]

Those bolts are 7ftb

[@badtothebone346]

You don't need any gasket sealer for the corners?

[@RBTheMechanic]

Yes u do honda bond or silicon works ok

[@josephcrowe9787]

What was the torque setting on that

[@RBTheMechanic]

The 10mm bolts are 7ft lb

[@grimey201]

I CtuLly need this done. Im in Jersey City. What's your price if I get the parts?

[@RBTheMechanic]

If u buy complete kit with spark plug bore sealed $190 if only valve cover seal $90

[@alexanderarko3943]

Good job done, but please can i get valve cover Gasket to buy? Thank you

[@81quiroz]

What cleaner did you use when cleaning around the area and what silicone tube did you use cause I’m doing work on mine

[@RBTheMechanic]

emmanuel quiroz brake cleaner used black silicon I think pvt regular silicon or u can use honda bond

[@ygbodybuilder3023]

So you used the same cover.why not replace the cover as well

[@RBTheMechanic]

It’s as customer requested

[@joshmorgan4180]

Does that part number fit a 2016 Honda Accord Sport I’m pretty sure it’s the same exact engine ?

[@RBTheMechanic]

JOSH MORGAN it’s the same same engine same part... please subscribe also subscribe to my other channel here’s a link kzbin.info/door/vqsPzqAZfVv_gjBYUFqNdg

[@johnblum2829]

Don't want your valve cover to ever leak? Change that pcv Valve every 30,000 Part #171305a2a01 $28.48 Takes a 10mm socket and 10 minutes.

[@ygbodybuilder3023]

Isnit true you can do this witout removing nthe spark plugs

[@RBTheMechanic]

Yes u can

[@cjzhang8031]

Where is your shop? My car has the same problem. I want to bring my car to you.

[@RBTheMechanic]

CJ zhang I’m in north nj Bayonne

[@arodriguez8762]

Not too far from me either, I'm in the Bronx with the same car but no problems yet. How much would you charge for this job?

[@javie4vr]

Thanks for the video! what are the torque specs. for the valve cover bolts? thank you for your help!

[@RBTheMechanic]

javie4vr 7fl lb I tightened it twice one the car was hot so the seal can warm up and be more smoother

[@luismarty1685]

Do you know what is the torque spec for the Honda V6 plastic valve covers? Also, do you know the valve clearance specs for the same 3.5l earth dreams engine?

[@RBTheMechanic]

What year

[@luismarty1685]

@@RBTheMechanic 2014 accord coupe 3.5l.

[@RBTheMechanic]

@@luismarty1685 I’m looking at similar car my computer dosent have the specs for exact year but it says .21 for intake and for exghust.25-.29 that’s in mm so u need to convert to in

[@luismarty1685]

@@RBTheMechanic Thank you. You don't have the valve cover torque spec?

[@RBTheMechanic]

@@luismarty1685 well u should but I been doing this for year I know when to stop and how the feel is anyways yes torque it if ur doing

[@yunglin9025]

Great video! What is the torque spec for the alternator power cable bolt(12mm)? Thanks!

[@RBTheMechanic]

Yunglin I’m not at workshop due to covid 19 but u can hand tighten it for now or search up somthing on google

[@kjrayo18]

Thanks for the video very useful!

[@RBTheMechanic]

Kelvin J thank you! Don’t forget to subscribe also check out my other channel rcusa201

[@LG-ig2ky]

How many miles this gasket was replaced?

[@RBTheMechanic]

L G the car had about 70k milages... please subscribe also subscribe to my other channel the name is rc usa 201

[@UnreachableSwagger]

I think this is very comon man. My honda same year model and it has 88 000 miles and is leaking oil not as much as this one tho. I can still see clean alumium on my engine. But its seeping. Thanks for the video helps alot so i can do mines.

[@alexmark1982]

Great job, man! Thanks!

[@pahanin2480]

I did this with a leatherman, 10mm wrench and a needle nose

[@sodapuffs]

great video..thank you

[@hikgerguy1234]

Nice video. Thanks for the effort. Can you explain why you used silicone in 4 spots on the valve cover before installing the gasket? Also, I noticed you didn't use Honda Bond or the black Permatex in 6 spots on the engine block. From other videos I've watched, people say it's critical to hit those six "seams" on the engine to prevent an oil leak.

[@RBTheMechanic]

The four spots is where the back cover and timing cover meets the engine. The other six are to hold the gasket in place not needed

[@hikgerguy1234]

@@RBTheMechanic I'm referring to the six areas where you can see what I'll call a "seam" in the engine block. There's three spots on each side. Multiple videos indicate you need to hit these with Permatex or Honda Bond to prevent leaks at these points. Take a look at this video starting at timestamp 17:44 kzbin.info/www/bejne/rn3Sf3mrbseSl5o

[@RBTheMechanic]

@@hikgerguy1234 nope only those 4 spot originals it comes there and we clean there.

[@finn1355]

You should put your eyes on the mechanical work you are doing !!!

[@RBTheMechanic]

Ok

[@bee2333]

What is the torque spec?

[@RBTheMechanic]

What’s year make model u got

[@bee2333]

@@RBTheMechanic 2013 accord sport 4cyl

[@RBTheMechanic]

@@bee2333 7ftlb

[@jossep1236]

do you have to know or have a video replacing the camshaft positon sensor on 2017 accord where is it located in the car

[@RBTheMechanic]

jossep1236 sorry I don’t have video on that but it should be up on the top check on both sides of engine

[@3232myke]

So do you not keep the coils in the same spot they came from?

[@RBTheMechanic]

3232myke no dont worry about they are same parts doing the same job

[@3232myke]

@@RBTheMechanic ok , where u get the adapters from , when the piece broke from that small hose

[@spokvlad302]

Hello! Tell me, what thermal gaps should be set when adjusting the valves? Accord 9 2.4 coupe

[@RBTheMechanic]

Spok Vlad I will find out any let u know to gap

[@RBTheMechanic]

The gap adjustment is.011-.013 exghust and Intake .008-.009 ... please make sure you vehicle double conform with dealer this is according to my data if the vehicle is diff it can damage engine

[@kaaarll]

Do I need to replace the gray sealant/silicone that you cleaned off?

[@RBTheMechanic]

Yes u can use regular silicon. That is the deal for side timing cover if it’s not flush it will seep small amount of leak

[@AntonAtan]

Whatever silicone you use it must be high temperature. For example RTV silicone.

[@tonyynewyork]

2017 honda accord se My Looks like wet around , i think is getting bad . 42k miles ( i think too early to go bad that early). Does anybody know how much Honda will charge me to replace that? Answer i would appreciate.

[@RBTheMechanic]

Honda might charge u $500 or more best do it yourself and get it done it’s not so bad let’s are like only $80 and yes it’s erly they all like that start at 59-60kmiles

[@hyltonanderson8353]

Hey RB The Mechanic nice video man! Do you know why my engine is leaking oil after the gasket was replaced? It also smells like something is burning once the engine heats up.

[@RBTheMechanic]

It might be leaking on to exghust check where it’s leaking from .. maybe the gasket didn’t sit flush ... did u trim out the gray sealer that I spliced with blade that would also make it leak it will not let the seal sit flush ...

[@Gladius797]

Thanks for info!! My engine rattles when I’m at a stop light and I can hear it from the inside like someone lightly banging or vibrating, any idea of what could be problem? Any help is greatly appreciated!

[@RBTheMechanic]

Marlon Z I have noticed all honda and Toyota engine do click click click noise on the new generation which is not problem check ur oil level make sure it’s clean and is changed on time other than that shouldn’t be a problem

[@Gladius797]

RB The Mechanic All checked and its good but this is more than the regular click , its like the engine is banging something when its at high revs and it moves and bangs against something, I have a sedan of same year and model and it doesn’t sound the same. Car is only 41kmiles

[@RBTheMechanic]

Marlon Z sounds like defiantly bad engine mounts Your engine mounts might be bad

[@IVAN2233]

What are the torque specs for a 2014 Honda Accord 4 cylinder? Doing this soon

[@RBTheMechanic]

7.2 ft lb

[@HtownRO]

My local dealer said they cant sell the spark plug seals without buying the entire cover

[@RBTheMechanic]

yes it comes all in package it will have 8 o ring seals for the screws of the spark plug seals

[@forfun6273]

What is the torque spec??? Why wouldn’t you say that?

[@RBTheMechanic]

What yeah is ur car I can give u toque every car is diffrent so I try Not to Confuse but my new videos I add years and specs

[@dsyple8187]

Good job, very helpful....your voice reminds me of my pops..

[@aliciamaguellal1832]

Where do you live?

[@RBTheMechanic]

Love or work? I’m in bayonne nj north

[@valknutd.5528]

will tube seals fit without replacing the whole grommet? i got the felpro but it only comes with the plastic tube seals without the base to screw it into it.

[@RBTheMechanic]

Not sure I think it seats on to it not side in to it. So if it seats on it it will fit

[@hectorheredia311]

Thanks for you video I will try to do it next week 👍🏾

[@RBTheMechanic]

@@hectorheredia311 ok bro let me know how it went

[@hectorheredia311]

@@RBTheMechanic Mission accomplished, I changed the gasket today on my accord 2015, one more time thanks for you video 💪🏾👍🏾

[@RBTheMechanic]

@@hectorheredia311 good job bro anytime always here to help with anything just send me message codes brakes any type of stuff with car ...also u can check out my other channel here’s a link kzbin.info/door/vqsPzqAZfVv_gjBYUFqNdg

[@Saleh-dq6pp]

Is it necessary to apply silicone glue ??

[@RBTheMechanic]

If you notice where I cleaned on the engine head with blade I showers to remove the silicon that is the seal for timing cover it will leaks so yes please put some in that areas it’s most important

[@Saleh-dq6pp]

@@RBTheMechanic Thank you May I have the glue link on amazon

[@RBTheMechanic]

@@Saleh-dq6pp J-B Weld 31319 RTV Silicone Sealant and Adhesive - Black - 3 oz. www.amazon.com/dp/B00ID8F8E4/ref=cm_sw_r_cp_api_glt_fabc_6X1BHCNF76WM7X6W7F9B

[@Saleh-dq6pp]

@@RBTheMechanic Thank you

[@AntonAtan]

Get high temperature Red RTV. Black is not for engine use .

[@finn1355]

clean the valve cover gasket seal track out with Qui-tips and alcohol than let dry.

[@RBTheMechanic]

Yeah that would be nice too