HONDA AND CLONES / GXV 160 CARBURETOR REPLACEMENT

[@bruno6919]

Very good video thanks you

[@raymondfrato367]

Don't mean to be picky but you missed showing the replacement of the black spacer block before putting on the new gasket between the cylinder and the carb. Love your videos.

[@THEMOWERMEDIC1]

Nope didn’t Miss anything but thanks for watching

[@raymondfrato367]

@@THEMOWERMEDIC1 you had it on there just didn't show it going on unless somehow I missed it twice. I have had customers that tried to do it themselves and switched the location of the spacer and the gasket.

[@THEMOWERMEDIC1]

@@raymondfrato367 dude it’s on there I promise. I didn’t forget it

[@raymondfrato367]

@@THEMOWERMEDIC1 Yes I know it is on there. I saw it on there. Hope you feel better soon. I just got over the c19 crud myself.

[@dannyhenderson5337]

Gxv 160 honda shaft starts at 1" tapers to 7/8 what will it fit

[@albertosanchez3350]

Hello there! I have a TB685ec 4 cycle that runs good but dies after a minute or two. it'll start right back up. I've replaced gas cap, fuel lines and primer bulb, also adjuted valve lash on 0.005" and still doing the same. Any clues?

[@magicone9327]

Did you ever get it repaired?

[@petermoygannon698]

Why would you need a new carburetor when you can clean jets . ???

[@davidphillips2259]

The best lawnmower repair man 👨 on you tube 👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻

[@rickthelian2215]

Great video hope your feeling better soon👍

[@themowerman]

Thanks for the video mate

[@bobbyscott8024]

Excellent!

[@DainichiKichi]

Looks like a very old mower. is that a Toro? what model is it?

[@stevef.9659]

I watch DIY videos from other countries and as long as they are done with the quality of capturing what you need to know, I love it. Thanks for a quality video because the process is etched in my mind because there was no distractions.

[@JazzyScat]

Help! Hi was wondering if you had any insight on a problem I have. I had to change the carburetor because the mower would only work on choke and would die on HI or LO positions. I didn't change anything else. When I pull the lever out of choke down to the Hi position the rpm is pretty much the same but when I put it on the LO position there is no change in engine speed which seems to be ok for the Hi position not certain. The motor is GVX120 4.4HP 1 cylinder Honda HR214 SX lawnmower. The governor arm is free to move if I push on it revs faster. There are no restrictions either on the idle arm where the 2 governor rods attach on the carb. Any Idea? Ever encountered this problem? Thanks

[@THEMOWERMEDIC1]

Need to double check carb install Make sure all the rods, springs, holes all went back correctly.

[@JazzyScat]

@@THEMOWERMEDIC1 everything is installed correctly. Very easy to do. Would adjusting the mixture and the stop screw affect the difference between the LO and HI?

[@billstiles487]

Great video! You make it look so easy, even a cave man can do it. Good job.

[@garyalensr]

Great video as always. So sorry your not feeling well. I just got over the sickness myself. It was a nightmare. Hope your feeling better my good man

[@Big_Johns]

Yes I too missed your audio Jeremy but it was still a nice video. Thanks bud 👍🏼

[@THEMOWERMEDIC1]

Got real sick and lost My voice Sorry man

[@Big_Johns]

No need to apologize brother, hope you get to feeling better soon. 👍🏼 If I could only get my wife to catch that. 😎

[@nashguy207]

Those carbs are fairly cheap and easy to replace. Good job buddy!!

[@bobshelton2812]

Hey buddy, good video. Are you afraid to report what that "parts & labor" cost was?

[@THEMOWERMEDIC1]

Free. I don’t Charge a dime for my services

[@josemorell1175]

Buen video 👍

[@fenceman53]

Good to go

[@jmonte2811]

Music annoying. It takes away from your excellent work

[@cravenmoorehead5636]

That genuine stuff has to be outrageous. A quick rebuild would sure be cost effective unless you decided to go with aftermarket. Is this correct?

[@vernonbruce3722]

Don't care for the lack of narration

[@THEMOWERMEDIC1]

✅been real sick the past few weeks give Me some compassion

[@vernonbruce3722]

@@THEMOWERMEDIC1 sorry to hear that you have been sick. I was just making an observation I wasn't slamming on you. Praying that you feel better. 🙏

[@ablelock]

I miss the narration. I could do without the music so it’s not gonna keep me interested.

[@THEMOWERMEDIC1]

Covid took my voice away sorry

[@ablelock]

Sorry to hear that the Covid took your voice away that is not good maybe you could do like a voiceover and have maybe your wife to narrate it. Is this going to be a permanent thing. I will pray that God will heal you and give your voice back to you.

[@meesau2112]

@@ablelock He said he was sick cut the man some slack. I'm pretty sure his voice will come back

[@richardybanez9052]

Brilliant New.Speaker Pelosi. Has Landed In Taiwan. Way To Go Nancy.You Rock. To The People Of 🇹🇼 The 🇺🇸 We Love/Adore You.This Administration Will Support With All It's Power.Richard.