HONDA CR-V POWER DOOR LOCKS COMPLETE DIAGNOSIS & REPAIR | 1997-2001 HONDA CRV

HONDA CR-V POWER DOOR LOCKS COMPLETE DIAGNOSIS & REPAIR | 1997-2001 HONDA CRV
Honda CR-V power door lock not working? In this video, pretty much everything you need to know: How make troubleshoot and repair door power locks electrical circuit on 1997-2001 Honda CR-V
Always check your vehicle specific service repair manual for any specs
Welcome to PistonSHACK Memberships Club:
/ @pistonshack
#hondacrv #crv #honda
Check "HONDA CRV PROJECT" Playlist for more interesting videos:
• Honda CR-V Project
EASY WINDSHIELD WASHER PUMP CIRCUIT DIAGNOSIS IN DETAILS | 97-01 HONDA CR-V
• EASY WINDSHIELD WASHER...
HONDA CR-V REAR MAIN CRANKSHAFT SEAL REPLACEMENT in Details | HONDA CRV 1997-2001
• HONDA CR-V REAR MAIN C...
HONDA CR-V FRONT CRANKSHAFT SEAL REPLACEMENT in Details | HONDA CRV 1997-2001
• HONDA CR-V FRONT CRANK...
HONDA CR-V Engine SWAP. Part 1: REMOVAL. Complete Tutorial.
• HONDA CR-V Engine SWAP...
HONDA, ACURA HARMONIC BALANCER aka CRANKSHAFT PULLEY BOLT REMOVAL.
• HONDA, ACURA HARMONIC ...
DISCLAIMER:
This video is only for entertainment purposes. If you rely on the information portrayed in this video, you assume the responsibility for the results.
Due to factors beyond the control of PISTONSHACK, it cannot guarantee against unauthorized modifications of this information or improper use of this information. PISTONSHACK assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. PISTONSHACK recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of PISTONSHACK, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not PISTONSHACK.

[@avaiseyama7121]

Hey! Was wondering what some of these tools are that you used. Super helpful vid thank you!

[@ollierobin]

Gen1 drivers door wiring harness 25 pin connector going into the door from the jam, the wires famously breaking breaking off the pins. There was guy making replacement 'pigtails' for the jam side of the harness as the door harness connector seldom seems to have problems; 100 bucks; solder or crimp yourself.Thanks!

[@The_M-An-M]

Well done. Very helpful. Appreciated

[@PistonShack]

Glad it was helpful!

[@nicolafabris1041]

Dear Mc Giver many thanks....I've the same problem on my 1998 CR-V ....Many congratulations for this complex repair ! Ciao Nicola from IT

[@PistonShack]

My pleasure Nicola. Did you get it sorted out?

[@EFGuy_Oregon]

Did you get this fixed? We have replacement connector pigtails. And if you need any in the future reach out @pistonshack

[@Chiefofthereef]

Came here thinking I’d give it a shot myself…. Nope lol great job though

[@PistonShack]

Any luck Carlos?

[@deanerhockings-reptilianhu8701]

Wow! You're a smart guy. I found what you did here so illuminating. My passenger side door lock just decided to stop working on my Gen 1. This video made me think about realistically all the variables I should check. I was just going to replace the actuator but like you say - I should check the basics. I knovery little about electrics though. Wish me luck:)

[@JosephDR]

Did you get it fixed? I have the same problem with my 1999 CR-V

[@user-vw1sy6ld2l]

You have the service manual, if you had the electrical troubleshooting manual you would have seen that you were looking at pin # 5 instead of pin # 16 in other words you were checking for ignition input on the yellow Hatch glass open output yellow wire. Your probably only had a bad Power Door Lock Control Unit and you probably broke the wires in the plug trying to disconnect the connectors inside the door. Pin #1 on the Power Door Lock Control Unit has no connection and pin #8 is the battery input so adjust your pin count accordingly. Your manual should show you the pin configuration and each wire color.

[@luis_techie]

Thank you so much.

[@PistonShack]

My pleasure Luis!

[@CarlosFlores-hq4sh]

Great video; thank you so much

[@PistonShack]

You are so welcome Carlos! How is your repair?

[@CarlosFlores-hq4sh]

@@PistonShack thank you, I found the same problem but at the other side... passenger side. The problem is gone, thanks to you.

[@frankrodriguez5202]

Loved the video...great help

[@PistonShack]

Glad it helped Frank! What was wrong with your Power Locks?

[@frankrodriguez5202]

@PistonShack Haven't done it yet...going to do it this weekend. But the video is so helpful 👍👍

[@EFGuy_Oregon]

@@frankrodriguez5202 if you need a replacement connector pigtail let me know!

[@ciscoclapper5826]

Any one notice the 20amp fuse was for the power windows?

[@user-wx3wc4bo7c]

Wife has a 99 CRV I originally started with fixing the car clock, well long story short I’ve replaced fuses, checked it with a scan tool , chased a passenger side window not closing issue, swapping spark plugs, oil change some body work next is the drive shaft break lines and now the power locks lol I started with the clock, I couldn’t figure out why my 03 Sonoma wouldn’t turn over so taking a break I’ve learned how to repair all of the things except that darn clock lol was pretty sure I would have got the Sonoma running but dropped the one Torx or T20 bit into the engine compartment and it was to dark to see at night 🙄🤷‍♂️🤙

[@levent8208]

Hi ! nice job I haven't investigated my problem much yet, the lock on the driver's door works but not the other door's lock, what do you think ? You really had to work hard on this one ! I'm from Montreal Thanks

[@markshiv3388]

I have that same problem on my Honda crv 2002

[@mikeg983]

Do you know a cheap place to get this part? My supplier can not seem to get it.

[@PistonShack]

Hey Mike! I got mine from Pick-n-Pull.

[@penguinfromhell9169]

I’ve connected the wires directly & it usually works for the day but the next day it stops! Any suggestions?

[@PistonShack]

What wires did you jump together?

[@notSusNugget]

18:55 fender removal

[@zackarytaylor6393]

But did that also fix the window that didn’t work? Also; happen to notice at all if your driver side speaker didn’t work while that bad Module was in?