The 89 is an awesome bike. Jeff Stanton said that it was his favorite bike.
@ArmathuX Жыл бұрын
Yes, AMA Champion bike. Good ol Hondas
@dudleylandsberg17476 ай бұрын
I had the 89 cr 80. That thing was fast. A lot of adults who rode it or raced against me with their 4 stroke bikes were shocked😂
@hbgriss Жыл бұрын
Beautiful bike
@ArmathuX Жыл бұрын
Thanks!
@Selinasdevil Жыл бұрын
First 2 stroke I ever had was a 92 cr250
@ArmathuX Жыл бұрын
Great bikes
@charlybabbet9362 Жыл бұрын
I MUST SAY IT AGAIN: OMG THIS 89 HONDA IS INSANE, WHAT A BEAST. GREETS FROM THE NETHERLANDS
@ArmathuX Жыл бұрын
Thx! Greetings from Finland
@hunterkembel5012Ай бұрын
@ArmathuX I'm Watching in ky USA
@TEKKYTWO Жыл бұрын
Absolutely beautiful bike sir
@ArmathuX Жыл бұрын
Thx! :)
@TEKKYTWO Жыл бұрын
No worries 👍 is the maintenance high on these older 2 strokes? Easy to find parts?
@ArmathuX Жыл бұрын
@@TEKKYTWO Hard to find parts but its worth
@jbnap3549 Жыл бұрын
Super clean screamer!
@rukkdaguylew8513 Жыл бұрын
Look at that blood red 🛑🚬🔥💯👈
@dominickcapito4420 Жыл бұрын
I love Honda. I wish they still made 2 strokes
@2StrokeBrothers Жыл бұрын
🔥🔥
@albundy6804 Жыл бұрын
Green suits u better bro!!
@guttersnipe3246 Жыл бұрын
Honda 250 strokes don't come much better 86 maybe but your bike sounds crisp
@donniebaker5984 Жыл бұрын
Check the crank shaft run out and see if it is about 0.003" out of round ..set to zero and feel the difference
@ArmathuX Жыл бұрын
Thx for tip
@donniebaker5984 Жыл бұрын
@@ArmathuX the factory gives a tolerance of about 0.003 " and says there good to go ..you can come that close in about two wacks with a brass Hammer ..the factory not going to spend all day truing up one set of fly wheels..but to take out that last 0.003 might take a good while and so the factory widens the window Heres what to expect you have it within 0.001" and. You hit the fly wheels one more time and jumps a 0.002" thats 0.001" too far ..hit it one more time back the other way and there is a good chance it lined up and reads all zero when you turn the crank by hand on a set of "V" blocks .if its out and all are off from the factory. One fly wheel will be ahead of the other ..if you think about the rod big end pin is trying to do s figure ,"8" and go up and down st the same time. And so does ypur piston .if you have ever seen rod bearing big end pin besrings thar are fat in the middle and then tapperd to a point on both ends the crank was off about 0.003". it will be a hole different bike when shes:"zeroed" out....check the torque on your motor mount bolts of the 8mm and 10mm. Its not very much 25-30 ft lbs for 8mm 45 - 50 for 10 mm but look it up ..
@tomduffy5129 Жыл бұрын
This guy has the crispiest 2 strokes I swear to god