Honda TPS calibration

In this video I will show you how to calibrate the TPS simply by removing or loosening two bolts on the TPS and using a voltmeter to measure the voltage as you make adjustments to the sensor.

[@fessorx22]

I had to replace my TPS and Throttle Body TB. Your blog/Video was very helpful. Please continue with this great material.

[@tanyagross404]

Thank you so much you are very helpful my first time trying to replace this on my own

[@RobbyJHope]

Thank you sir. I needed a refresher and will use a paperclip going forward instead of jamming my prongs into the backside. I found that 0.48 gives me a high idle. I wonder why this is. Brand new IACV too.

[@dannyortega8223]

That’s what up bro I was looking for a video like this 👍

[@builtjfilion934]

Thanks for watching!! Glad I could help

[@isaacgonzalez1160]

Thats was up

[@danv4655]

Very nice video. no music, no bs. very informative.

[@oscargonzalez8518]

Very important,no annoying noise,very good video, thanks I going to try my.

[@saginaw60]

The screws are JIS or Japan Industry Standard, not Phillips. Buy the correct screwdriver, and things will go better.

[@ilovemydb1able]

What symptoms were you having with a bad tps?

[@builtjfilion934]

Some symptoms of a bad tps sensor are check engine light, jerking, poor acceleration, no acceleration, high or low idle issues

[@jayzee9273]

What symptoms did you have that lead to this diagnostic test

[@builtjfilion934]

Sporadic idle, and very laggy or jumpy throttle response

[@andreg987]

Excellent video: simple, detailed, all of the essential wires to test and results.

[@builtjfilion934]

Thanks for watching!

[@yusufcinar6215]

Thank you very much for the video.. I have a 2003 model K20 Accord and I set the tps value to 0.5, it was working with a little vibration when the gear was in D position. My friend also has a 2005 model of the same vehicle. The factory tps value was 0.7, why is this so? I also set the tps to 0.7 in my own vehicle, the transmission makes a slight knock when slowing down.. What is the original factory value?

[@tanerdemirci8636]

Ne yazmıssın bilmiyorum ama tahminim sizde TPS sensörü sorunu yaşıyorsunuz

[@yusufcinar6215]

@@tanerdemirci8636 ayarla ilgili kafama takılan bişe sormuştum

[@tanerdemirci8636]

Sen sorununu çozebildinmi Yusuf bey benimde bir k 20 accordun var yıllardır sorunu çözemedim

[@tanerdemirci8636]

0.50 ye ayarlıyor buradaki usta bizimkileri 0.30 diyor

[@yusufcinar6215]

@@tanerdemirci8636 0.5 dir hocam normali ,fakat arkadaşım 2005 2.0 var ölçtüm 0.7 çıktı .. Ben 0.7 yapınca araç durmaya yakın silkeleme yapmaya başladı geri 0.5 e çektim

[@ernestfox425]

So today I literally watcher this video 10 times or more. When I get it set to 0.50 I can't get it to say 4.50 when the throttle is open all the way. It's impossible. I'm wondering is there a way to loosen the pull lever to get some more space .. when I open the throttle all the way it like 3.7 or 3.8

[@builtjfilion934]

It’s okay man sometimes the tps just won’t reach 4.5 as long as it’s close but if it’s way out of spec and causes acceleration issue then I would replace the tps itself. Again it’s okay if it not perfect because electric tps especially aftermarket is never 💯%

[@oogrily6990]

What if my battery is located in the back? Where can i hook up the negative wire?

[@thunderbembo3406]

can hook it on shortbody wire or directly to car body for -ve terminal.

[@builtjfilion934]

Any ground on the body of the car is considered a good ground

[@WilliamD-ni7yq]

Good morning boss, my car is a Honda Fit 08 cvt, I cleaned the TBI, but now it's shaking when I put on the reverse with an AC on, I put the multimeter on TPS and it is reading 0.51 v closed and 4.58 open. Do you think it good ?

[@titanace3981]

Awesome

[@builtjfilion934]

Thanks for watching!!

[@titanace3981]

@@builtjfilion934 it helped ♥️

[@MariaGarcia-ij4fz]

Nice keep on going GOD bless you and your family

[@MegaMikerojas]

Mine is at .50 at closed throttle and 4.25 at wot. Any help?

[@builtjfilion934]

Yes the tps is either installed wrong or broken. Try removing it and seeing if it damaged, if it is replace it and calibrate it.

[@metzmatu8409]

0.5V at closed throttle is perfect setting. 4.25V at WOT is acceptable, thou 4.5V is preferred.

[@renaissancemaneric8019]

Thanks for dropping this

[@arturolarios9005]

Thank you for your video, I am going to do this procedure before I gonna buy the tps for remplacement.

[@mn029]

my motorcycle reads 2.5Volt in close position 😪 inline 4 650. sudden engine stall , black smoke what could be the reason

[@builtjfilion934]

Black smoke always makes me suspect engine damage possible bad rings or burning oil from head into combustion chamber. The volts should be higher if I’m not mistaken for a 650cc bike under load, but it’s hard to diagnose without actually being there.

[@frias2287]

Nice job🔥💯

[@builtjfilion934]

Thanks for watching!!

[@alfonsoleonardo6178]

Nice video was very clear.

[@builtjfilion934]

Thanks for taking the time to watch and comment on the video!

[@Silenceplz595]

Do the car have to running?

[@builtjfilion934]

No just key in ignition on the on position

[@shuckyducky3508]

K24 element same numbers-??

[@celest6239]

Is the car completely on when u check the voltage? I tried touching my red wire of the voltemeter to the red wire of the tps but I got no signal

[@builtjfilion934]

Key on engine off

[@mlungisiwinstonmagongo4559]

clear....thanks for sharing

[@builtjfilion934]

Thanks for watching

[@cariefeslowley9920]

Vehicle gotta be on?

[@builtjfilion934]

Yes have the key in the on position

[@1234570505]

Gracias por tu ayuda saludos desde México!!!

[@builtjfilion934]

gracias por sintonizar mi canal

[@ryurc3033]

Bungie chord doesn't bother me a bit, but that ground.....ooooof......bro.

[@builtjfilion934]

Thank goodness the cars totaled now lol

[@ianmancusomma]

Mine reads 1.5 volts

[@builtjfilion934]

You might need to recalibrate your tps, it all depends on your set up.

[@victornavarro6560]

Mine does not go up to 5v when i open the throttle

[@moremoney2]

It’s not supposed to. Open throttle is 4.5 volts, closed throttle is .5 or (1/2) volt. Watch your decimal points.

[@maxshort437]

👍 nice

[@builtjfilion934]

Thanks for subscribing 🙏

[@oso251]

I replaced the tps, then I followed the video and the idle is running high. How can I get them back to normal?

[@builtjfilion934]

Sometimes when you tighten it it moves so check and adjust as needed

[@payangpy]

What if I can’t get to a 0.5 ?

[@builtjfilion934]

It’s okay get as close to it as possible, after your done take it for a test drive. To check for any issues

[@systemunderground]

​@@builtjfilion934if thr lowest I can get is 1.2v is my tps failing already?

[@builtjfilion934]

@@systemunderground if your throttle response isn’t acting correctly and you’ve e tried adjusting it a few times, the TPS can be faulty it happens all the time with aftermarket parts, if you can afford OEM that’s the best way to go.

[@piusigbinomwahia6016]

Very clear and informative. should the ignition be on?

[@builtjfilion934]

Yes ignition should be (ON) with engine off

[@augiegonzales7025]

Does the key have to be in on to get power to the connector? Good video

[@builtjfilion934]

Yes have the key in the on position

[@Jaime-py3ly]

Gracias 👍

[@builtjfilion934]

Welcome 🙏