The ratio of ingredients and timing of steps of whole procces is not mentioned so vedio is incomplete
@RabiehRabieh-qi7ff7 ай бұрын
هل يمكنني استخدام نترات الامونيوم بدل نترات البوتاسيوم
@erkanun2 ай бұрын
Eskiden "eşek idrarı" ile yaparlarmış. Yaşlılar anlatırlardı. Sanırım KNO3 yerine onu kullanıyorlardı. Anlatılanlar şimdi mantıklı geldi.
@alpsaral4 күн бұрын
Çok sağlam iş yaptı ama. KZbin'da gördüğüm en kalite menevişlerden birisi oldu
@danielelamincia14045 күн бұрын
Quale è il rapporto degli ingredienti specificare il nome
@Igotknobblies8 ай бұрын
I need to blue my BSA airgun. It's long so I have to make a long boiling tank. Copper would be the easiest with ends soft soldered on. Would this impair the job? Also dies the nitriding not affect the rifling? I was thinking of stoppering the two ends.....
@azlee1017 ай бұрын
Hello. Thank you for the tutorial... Just wondering... What is the ratio for ingredients... Thank you
@punjabengineeringworks76127 ай бұрын
Equally all three kno3 ,wather ,NAOH for example 1000gram,1000gram,1000gram capacity u require
@egzonabajrami23174 ай бұрын
what are these products called?
@egzonabajrami23174 ай бұрын
@@punjabengineeringworks7612 what are these products called?
@philculler85844 ай бұрын
@@punjabengineeringworks7612 KNO3 is potassium nitrate - a fertilizer, water is Distilled water, NaOH is Sodium Hydroxide (LYE). Some lye (drain cleaners)contain zinc chips, that will screw up the solution.
@patung19902 ай бұрын
@@philculler8584 Will this process change the temper of heat treated metal?
@blazer804910 күн бұрын
lame
@madmike93982 ай бұрын
no offense... but that looks like a khyber pass glock barrel lol
@raplopez425811 ай бұрын
Easy to understand
@rabieh54314 ай бұрын
نترات الامونيوم بيمشي الحال
@bienvenidomalinis83962 ай бұрын
wer can i buy the KN03 and Na0H and NaN02??? can i use it in my motor cyckle parts?
@bikerdick9425Ай бұрын
Home Depot. Lye is drain cleaner and potassium nitrate is some crap for use on tree stumps. If i can remember the name, l'll post it. You can blue motor sickle parts, but you'd do better parkerizing them. Easier, too.
@ЮрийМамонов-я3л7 ай бұрын
Зачем столько лишней работы к чему это?
@chrismartinez98077 ай бұрын
This does not affect the heat treat of the steel?
@ehabzaman75607 ай бұрын
Is this color permanent like compney or removable.. if i color the gun like this and then i used it or do firing on it… so the color will be removing or not?
@TheStigma7 ай бұрын
Don't know what compney is, but bluing makes a layer of oxide (like rust, but much more stable). The main use is as a layer of protection against (red) rust, but it should also be oiled because bluing alone is not impervious to rusting - but it helps a lot. Because it is an oxide layer it can be worn off, sanded down, sandblasted or acid-bathed to expose the raw metal. Thats not something you want to often on presicion parts though, because you would be removing a thin layer of metal each time. Its fairly tough and holds up well on tools, but I expect it would eventually wear though on moving gun parts unless everything is kept well lubricated. You can use other chemicals to cold-blue also if you mainly want the esthetics. thats super easy to do with just a brush after thorough degreasing.
@clivewiddall34302 ай бұрын
Common name of chemicals would help
@bikerdick9425Ай бұрын
Lye & potassium nitrate...and the liquid looking stuff is water. (lol... sorry, l hadda say it!)
@Ralph_VerasАй бұрын
Where to buy the NaON chemical
@tylermiros8612Ай бұрын
NaOH (Lye/Caustic Soda) is used for plumbing and soap making, try a hardware store
@Rusty-Ak127 күн бұрын
Any chamical store
@Militarycollector6 ай бұрын
Steel tongs….???
@DefinitiveRodsNReels2 ай бұрын
I mean, it ain’t meth he’s cookin’
@FrFr2248 ай бұрын
Don’t use a wire wheel
@gillihansmobilewelding8 ай бұрын
Why?
@mtopuk7 ай бұрын
İts okey using wire wheel but must be soft one
@mtopuk7 ай бұрын
Super simple treathment. Burnt engine oil bath at the end remind me old days.
@rendyshofwanpratama69747 ай бұрын
I've tried it and it really works! Great & simple! Good job brother!
@donemigholzjr.73449 ай бұрын
Where do you get oil that black?
@꿈틀꿈틀-e6p9 ай бұрын
I think he used some kind of industrial oil. My grandfather used to use something similar to lubricate his factory machines back in the day
@jimmatrix72449 ай бұрын
Used engine oil from car or motorcycle.
@kristianbraun56048 ай бұрын
It looks like dirty motor oil
@saqibwazir22067 ай бұрын
im from Pakistan 🇵🇰 thanks brother very informative video.
@ratishpatil45825 ай бұрын
I am from india...and there goes the neighourhood
@dustintaylor407610 ай бұрын
What is the ratio on the ingredients
@fearlyenrage9 ай бұрын
Natriumhydroxid: 400 g Kaliumnitrat: 10 g Natriumnitrit: 10 g Wasser: 600 ml When the nitrates gets used up in the process, what it will because those are the main oxidizers add some teaspoon of unslaked lime powder CaOH. That will get the oxidizers back on track. Also you can recharge the oxidizers by adding more of them. Not all steels will show a fine result because of the alloys in them. Here is another clip with good explaination kzbin.info/www/bejne/jIe7qXVseLSIj9U
@jimmatrix72449 ай бұрын
@@fearlyenrage What is "Wasser"?
@fearlyenrage9 ай бұрын
@@jimmatrix7244 the essence of life on this planet. Aka H2O
@The1jonnyz9 ай бұрын
@@jimmatrix7244water
@INNOARMS9 ай бұрын
@@fearlyenrage NaOH 400 g KNO3 10 g NaNO2 10 g Water 600 ml right??