HOT TAPPING WITH TONISCO B30 USING FLANGED WELDABLE TEE AND FLANGED GATE VALVE

[@RoyalProdigy]

Not sure why I sat through that. But I learned a new skill ill never ever need

[@cooperstown2971]

METAL SAMPLES is the best hot tap tool known to man, we just got it up here for the Arctic Oil lines and it is flawless!!! EVEN IN -50 BELOW !!!!!!!!!!!!!!!!

[@geoffroyfalot3583]

Where were you working at ?

[@slit4659]

I've done about 7 hottaps in my day it's scary when you first light up. the welding inspector ut'ed the pipe(that's to check how thick it is) I asked him to stick around while I first lit up, should of seen the look on his face... he did stay...12 " weldolets took most of the day...... 342 retired.

[@rafordy]

The pilot drill did not appear to have a retaining clip that secures the the coupon that the whole cutter creates ? if not its going in the system.

[@gregg4164]

Yeah it was the kind that have the wire that tucks into a slot on the side of the bit. They suck as the wire usually doesnt come out when you need it too.

[@santiago64837]

Hi , What type of drill is being coupled to the shaft ?

[@napornik]

The background muzak... do I have to play it out loud while tapping, or can I have it through my headphones???

[@FranklinKekeke-k3h]

Good experience

[@FranklinKekeke-k3h]

Cost of 8inch hole saw including pilot drill

[@policronia]

this seems like such a complex procedure. i didnt notice any torquing and perhaps one measurement taken. how come the flange on the tapping machine has far less bolt holes than the flange on the valve?

[@glennschaub6303]

No pressure on that side

[@yagoubyassin4330]

very nice

[@gregg4164]

And why would you do this demonstration on SS pipe? One good way to burn up a bit and hole saw.

[@A3Kr0n]

Jamming out to hot tapping music.

[@sashankvissa2358]

awesome

[@apburner1]

"Carrie on drilling"? With spelling and proofreading like that I wouldn't let you unclog my toilet.

[@georgesmith6891]

I noticed the magnet for shavings and dick capture, what would the process be if one wanted to do this on stainless steel?

[@georgesmith6891]

Disc* stupid autocorrect 😳

[@drone521]

Just waited to see if remembering to open the valve was in the instructions!!!.....tapping thru 2 gates a stem and the pipe make for a real bad day .....don't laugh....it's been done more times than u would ever believe!!! Personally, I would have opened that valve before doing anything else....my second check of valve position would have been when I measured cutter travel thru the valve body not outside of it.

[@allamsantos8095]

BRASIL 🇧🇷🙄😎👍

[@Frankb932]

Brasil 1 - 7 Germany ahahah

[@franciscobanda6790]

Esto es para una perforación muy ligera, Y demostrarlo en una linea viva. NO convencido.

[@By_KOSOVALI]

Bu kadar şey için bir video bu kadar uzatılmaz insanların zamanını çalmak demektir bu ben bu videoyu kimseye tavsye etmiyorum

[@just1lifexx11]

pay 200 an hour, i still would for that kind of job... its akiller explosion... hey ill trade you an iphone 4 both of you kidneyss.. jahajjaj

[@corrychamberlin9539]

All that ppe seriously...

[@davekgill]

Ok... good vid but... Who would do all that set up in full Garb....including brand new gloves. Not this sailor.

[@judclark7376]

I came for the tapping and stayed for the scruff

[@joseroman562]

muy largo para tan poco contenido.Muy aburrido

[@gregg4164]

This aint Pipe Fitting 101 show me the fucking tapping machine.

[@lukelinsmeyer5999]

If you have to read the instructions you should not be doing this on a live pipe.

[@swss12]

+Luke Linsmeyer that's the whole point of it. or else he would just be installing a fat sockolet or putting in a tee

[@lukelinsmeyer5999]

+Devo yes but when you practice you don't do it on a live pipe. By the time you do this on a live pipe you should be good enough to not read the instructions.

[@swss12]

oh i see what you mean now. i thought you meant the instructions say dont do it on live pipes.