Hotpoint washing machine. How to remove the agitator. And more.

[@katherinemrogers]

I don’t usually comment but I just wanted to say thank you sir. My mom and I were alone and really struggling because we had a part of a blanket stuck in the agitator. Luckily after hours of trying to get it out I found this video of our exact washer and realized I could take off the agitator and save us even more time and money. When good people like you make these types of videos you help out other people you’ve never met when they need it the most. It really is very kind thank you so much. I’m tremendously grateful. God bless you and your loved ones.

[@ericinalaska7648]

Well thank you. Im glad it helped and sounds like you were able to get done what you needed.

[@PEIfiddler]

this really helped me in cleaning under the agitator, you might want to mention to line up the groves in the agitator when you put it back on.

[@ericinalaska7648]

Glad it helped with your mission. As you mentioned. There are ribs on the hub and grooves in the inner diameter of the agitator that line up. I just kind of eye balled the relationship of the paddles and the orientation to each other, (grooves, ribs,) as I placed the agitator back on. Always good to have any feedback to share with people if I missed some thing or some thing needs some clarification.. Thanks for that.

[@finderskeepers47]

This was a very helpful video. I was about to destroy that little dome because i thought that was the only way to get the agitator off to clean it. I had no idea it just pops off.

[@ericinalaska7648]

Primary motivation for making this particular video. Many models require the dome removal and a nut under neath. Once I figured that out on this one I thought. People would want to know this. So there we go. Glad it helped.

[@TheDPerrin]

I have this exact machine and saw all those other videos before finding this on.e When I got to that dome you were talking about, I tried to gently pry it loose (as other videos said). When it wouldn't budge easily, I looked again about this specific make and found your video. THAT WAS SO EASY! I'm glad I stopped just in time or I would have broken the screen dome too. Thank you VERY much for this

[@ericinalaska7648]

Perseverance pays again. Love it when a plan comes together. Long live your washer.

[@cjfah657]

THANK YOU ERIC! Luckily I found your video before I started wrestling with my washer. You saved me time and frustration. Glad I found you.

[@ericinalaska7648]

You're welcome! Glad it helped.

[@TheeAriaLee]

Thank you bro! I appreciate you teaching us something that NO one else has!!!

[@ericinalaska7648]

Well thank you as well. Just passing on what worked for me. Glad it was of help and hope it fixed what ever issue you were addressing.

[@barbraclampitt3527]

Thank you sir! My curtain tie backs got wrapped around under the agitator - I followed your directions and I was able to remove the curtain successfully! Thank you again!

[@ericinalaska7648]

Excellent. Glad it helped.

[@tinamagill606]

This video was GREAT. I have a Hotpoint and a mattress pad got twisted around underneath the agitator. I looked at various videos like he did. So thank you for making this one. I had to put my dog leash underneath and my son helped pop it off. From there it was easy. As many times as I have washed these never ever had this happen.

[@ericinalaska7648]

Glad it helped. The first time I pulled it out. Leaning over it, pulling on it firmly with both hands. I jabbed myself in the ribs pretty good when it let loose. So going through the steps again, made it a little easier. Thanks for the feedback.

[@gordonbyers7702]

Great video, agitator came out just as described. Had to remove the old stringy rag wrapped around the agitator. Thanks 👍

[@ericinalaska7648]

Glad it helped.

[@pepemartinez2377]

My wife put my daughter’s swimsuit and the cord from the upper part got stuck underneath the agitator, thanks to your video I was able to remove it.

[@ericinalaska7648]

Yep bras etc. Common. Glad it helped and all worked out.

[@brendaday2033]

Thank you for the video! I'm still trying to figure out my issue but it was definitely helpful to rule things out.

[@ericinalaska7648]

Glad it was helpful. Hope your able to sort it out.

[@CoyoteRidge]

Thank you, stopped me from destroying my cap

[@ericinalaska7648]

Fantastic. I sacrificed mine for the greater good.

[@floydcarey7727]

That was the most helpful video I found on anyting I worked on. most times you ask what time it is they tell you how to build a clock thank you for the video very helpful.

[@ericinalaska7648]

Glad it was helpful. Thanks for the feedback.

[@aprilm4338]

Thank you for sharing this video. We saved money for looking at your video!

[@ericinalaska7648]

You are welcome! Glad to hear it.

[@alf1656]

Thanks for the video. It covered every issue I'm having. I'm really glad I watched this before digging at the top part anymore!

[@ericinalaska7648]

Glad it helped. Yah As I think I mentioned in the video. I destroyed that top part to get at the non existent nut underneath. Thought that was worth sharing. If you have the same model The parts I used are in the description. For reference.

[@billd.8585]

I am grateful you shared your knowledge of this Hotpoint agitator removal. My daughter caught her work smock string under it and I had to remove it to get it free. I worked on a few machines in my day but never had one you had to just pull up hard on on it . I would not wanted to pull so hard to get it in off if it wasn't for seeing your video. Thank You Very Much!!

[@ericinalaska7648]

You are welcome! That was the man reason for making it Id say. Because most have the nut under the softener cup. It was something I thought worth sharing to help others avoid the mystery. Glad it worked out for you.

[@coltsevin]

Wow... Thank you for the video. Need to replace the tub seal, and was about to go full send on it since it wouldn't unscrew like all the other videos say. The agitator thanks you as well. 😂

[@ericinalaska7648]

You're welcome! Glad you found it helpful. I wish you success.

[@skipbrazil679]

Great video. It was exactly what was wrong with it. I thought it was a bearing. Good job!!!

[@ericinalaska7648]

Glad it helped. It can be a rude awakening when that thing starts letting you know it's unhappy. Make sure you snug that nut tight. A few good taps with a mallet. Cranked Hand tight sometimes just doesn't do it. And it can become unhappy again after a few loads.

[@GhostProtocol.System]

I’m happy to find a video on how to take this out. I gotta get under mine to figure out why it keeps eating the strings to all my jackets and pants.

[@ericinalaska7648]

Just don't let it jab you in the ribs as you pull it out like I did.

[@GhostProtocol.System]

@@ericinalaska7648 luckily I read the comments and someone mentioned a dog leash to pull it out, which I did have on hand.

[@51ghardy]

Thanks for this. I would not have just popped that out because I am a scaredy cat. Thanks again

[@ericinalaska7648]

Glad to hear it helped. Good luck.

[@CharlesGoddard-l8e]

Thank you Sir, worked like a champ!

[@ericinalaska7648]

Good to hear.

[@jean-francoisdion2355]

Yes! I will be able to take off the basket of an old Hotpoint washing machine and convert into a outdoor firepit. Thank you so much!

[@ericinalaska7648]

You are so welcome. That is of course another fantastic option. Hahaha! Assuming yours isn't plastic or plastic coated like mine.

[@jean-francoisdion2355]

@@ericinalaska7648 Finally, there was a bolt under the soap bowl. After unscrewing, I only had to pull out the transmission shaft. Got my drilled basket for firepit, fantastic!

[@ericinalaska7648]

@@jean-francoisdion2355 Hahaha! Fantastic. Enjoy.

[@BiGlittleCaTs]

When you unscrew the bolt the plastic dome is stuck and won’t come out easy like you did. What should I do? But Thank you very much for posting this video, I have the same issue with my washing machine. ❤

[@ericinalaska7648]

Are you talking about the tub nut. After you remove the agitator?

[@BiGlittleCaTs]

@@ericinalaska7648air bell coupler is stuck

[@sourkraut6248]

THANK YOU !!! This is just what I needed to know. I would have broken that cap too. I owe you a beer.

[@ericinalaska7648]

Great. Yep that cap and what I learned as I went is basically what inspired the video. So mission accomplished? Fantastic.

[@marydick3865]

Saved me a service call! Thank you!

[@ericinalaska7648]

Great to hear! Always the desired outcome.

[@yolandataylor1321]

Thank you so much for this video. My machine is making a very loud grinding sound when it starts to wash and don't do it in the spin cycle. Can you help. Have the same washer machine.

[@ericinalaska7648]

Tuff one without eyes on it and seeing and hearing. But my issue with the parts I had to replace was when it would spin it would behave like an out of balance load. Because the tub was loose and parts got sloppy . A grinding sound isn't something I experienced. If your not familiar with working on stuff like this Id see about getting someone who is to take a look. There really isn't too much to them that it can be. Motor, water pump, tub assembly, electrical Sheet metal body/frame/panels water supply and drain hoses. But labor adds up. If you can't or cant get family or a friend to look. You should be able to get a service call for a flat rate and then get an opinion to decide if its worth fixing or replacing. Hope that helps.

[@brentolivo2963]

Thanks Eric, was stuck on how to get off.

[@ericinalaska7648]

Good deal. All I could hope to do is help in such a situation.

[@ericinalaska7648]

I just noticed this comment is from 1 yr ago. I just got a big batch of older comments. Very weird. But Thank you.

[@Mrswlsn]

Very helpful. Thank you!!!

[@ericinalaska7648]

Glad it was helpful. Thank you.

[@janetfisher3438]

Hey sir, thank you sooooo much you are magical man. You really have made my day. Thanks for the help and cool video. Really easy to follow. Good work my friend!

[@ericinalaska7648]

Sounds like you were able to complete the mission. Or least dive in with confidence. Thanks for the feedback.

[@lillychala]

😊 Thank you!!! Made my day!

[@ericinalaska7648]

You're welcome. Hope it worked out.

[@RiverbendlongbowsOutdoors]

Thanks buddy. I just destroyed my dome cap as well 🤦‍♂️ I wish I would have found this first

[@ericinalaska7648]

Hahaha! Yah. Guess no more softener. Glad it helped though. Better late than never.

[@RiverbendlongbowsOutdoors]

@@ericinalaska7648 😁 what sucks is i can't get the tub nut out now 😅 Seized up big time

[@ericinalaska7648]

Not to insult, but you are aware it's a reverse thread? Hopefully its that simple for you.

[@RiverbendlongbowsOutdoors]

@@ericinalaska7648 😅 yes I am. Its just extremely corroded

[@ericinalaska7648]

All joking aside. Pipe wrench and a hammer. It takes a decent crank to tighten it properly when installed. I found when tightening it if I just got it as tight as I could by hand or tapping it with my palm until the drum turned. It wasn't enough. It would loosen up again after a few loads. I put a short handled pipe wrench on it and hit it a few good times to really snug it up. Never had a problem since. I guess my point is that even without the corrosion its likely on there pretty good. But hopefully by the time you get this you've sorted it out.

[@lindabowers1883]

How do I get the dome off or out. I’m a women and pretty independent so I’m stuck now. Thank you so much it was really helpful

[@ericinalaska7648]

If you have the exact model as this video. You don't need to remove the dome. Other models will have a fin or something you can grab with a pliers or the like and pull it out. And there would be a nut under it to be removed. That then frees up the agitator. In the video I mentioned that I removed mine, and destroyed it basically based on other references and learned I didn't need to. This model you can simply pull the agitator out. No reason to remove the dome under the softner cup. No need to remove the softener cup either. Just pull it out as a unit. Some models may require it though. So if you don't have this model you can pull and pull and its not gonna come out.

[@alaskanken2132]

They don't make them like they use to.

[@chiefstrategist-mp6rn]

Is there any play on the agitator mechanism once agitator removed?

[@ericinalaska7648]

Do you mean after reinstalling it?

[@John-1984]

Thanks for the video. I suspect my agitator coupling is bad and wasn't sure how to remove it.

[@ericinalaska7648]

Glad it was of help.

[@FlipGz]

I don’t even have a washer and I’m watching...I guess I’m a true nerd

[@ericinalaska7648]

Well thanks.Hope you got some entertainment out of it.

[@ericinalaska7648]

Maybe you'll find yourself entertained by the kzbin.info/www/bejne/gpylnph4oK6jkLM Concrete project making a new counter top for my BBQ.

[@rickybrooks6907]

I'm having hard trouble taking the bolt off that's goes counterclockwise

[@ericinalaska7648]

The tub nut?

[@Ky53m]

Great video, I do have a question though, is removing the front and top panels difficult? Like is there anything I need to be aware of? Thanks.

[@ericinalaska7648]

Hey Kyle. Pretty easy actually. First of course unplug and disconnect and or shut off the water. This unit and most have a couple of release clips on top of the front panel between the top and front panel.. I usually use a thin putty knife. Slide it in between the front panel and the top against the clip and either push firmly or sometimes whack the end of the handle with my palm. you should be able to look maybe with a flash light to see where each is. About an inch or two from each end. Then remove the front panel by pulling out on the top and then up and of the bottom retainer/clips. Set it aside. The top has a screw on each side in the front. Remove those and it frees the whole top up pretty good. You'll notice some wires. Those are for the sensor that tells the machine if the top is closed or not. So when you open it mid spin it stops spinning etc. Safety. You can release that from the bottom and turn it so it will fit through the slot. Feed it through. and then you maneuver the top off. The rest is held in place by kind of hooked edged and slots. I believe you push back and lift up to release the sides. And I believe the rear releases by pushing to the left. And lift out. I just kind of do it and am reliving it in my head. It may be slightly different. Rt instead of left and forward instead of back but you get the idea. And just repeat in reverse when reassembling. To get the tub out you have to release the back panel. With the knobs on it. Also pretty simple. Screws on the front bottom and back if I remember correctly and release. And swing it backward out of your way. Plenty of play in the wires to do so. Hope I wasn't too vague and this helps.

[@Ky53m]

@@ericinalaska7648 This is really great and thorough, I'll give a shot. Thank you for the explanations, keep up the good work!

[@Judeith]

I have a problem with my washer and my dryer I cleaned it real good I checked all the fuses all good . Heats up all around the dryer but not in the dryer tube it’s self so do y’all have a video

[@ericinalaska7648]

I don't but I would suggest a couple things based on what you tell me. Im sure you know about cleaning your lint trap/screen. But your line out, Im assuming that's what your referring to when you say tube? Can get plugged aes well and should be cleaned at least annually. One of the most common causes of house fires.

[@rodneysexton1034]

How much does a new agitator cost? Great video!

[@ericinalaska7648]

Hey Rodney. I was looking at a few things such as a tub. Tub Hub. And Tub bushing and nut. I recall around $35 to $50ish for a new agitator. Plus shipping likely. And certainly there are some for more, but you should be able to find one new in that range. For this particular model anyway. Also keep in mind that's just the agitator. Not any other parts you may want or need for the assembly. All parts sold separately.

[@thenarutoboy1017]

thanks man are washer had a jacket is it and went under the agitator so thanks

[@ericinalaska7648]

Glad it helped.

[@janetelliott3788]

Guess Im not strong enough. Tried to remove the softener part to clean it and wasn't able to pull it up and off. Thanks for showing me though.

[@ericinalaska7648]

Yes it may take a firm grip. Maybe you can get some help.

[@brendaday2033]

To get mine off I stuck my fingers inside where you pour the fabric softener. There is a lip there and I pulled it up easily. The agitator required a flat dog leash. I'm around 5'2 and was honestly afraid it would hit me in the face so the leash kept me at a safe distance and gave me additional leverage. Hope this helps! I have the same model as what was shown.

[@kennethbaker4071]

awesome teach and thank you

[@ericinalaska7648]

You are very welcome.

[@bigblob1583]

This video saved my ass

[@ericinalaska7648]

Mission accomplished then huh?

[@bigblob1583]

Yes sir thank you!

[@jswranch]

Thanks. This video helped me.

[@ericinalaska7648]

Glad to hear it.

[@edpratt3977]

I knew I would blow out my back with a quick jerk & pull, so I set it up with a ratchet strap and and a long 2X2 set on towels edge to edge on the washer...It popped right off after about 6 clicks...

[@ericinalaska7648]

Excellent. Many ways to come at it for sure once you determine its that kind of setup. The pop off vs. retaining nut style.

[@raditian2]

What is the trick to get the agitator back on completely.

[@ericinalaska7648]

No trick. Should just snap back on. May take a good oomph. But that's it. And it may need a little time for the plastic to spring back or relax into its most secure position. Are you having trouble? Or maybe its taking a little more persuasion than you thought it should or would?

[@raditian2]

@@ericinalaska7648Thanks for response !! I may have it in there not sure .Didn't hear a snap . Rubbed thin layer of Vasoline down where snaps are located for smooth slide. Stuck thin board at bottom of pulley . So pully wouldn't smack bottom so hard. Should be enough room for the fingers to slide under bottom agitator ?

[@ericinalaska7648]

@@raditian2 Well My recollection is it was a bit time on the fingers getting them under to jerk it out. But if your feel like its in. It should again take a jerk to remove it. Probably not as much as the first time you took it apart but still resistance. If you can jut lift it out its likely not seated properly and all the way on.

[@dantesprophet9612]

Can someone tell me what that grey/chrome colored circular disc looking thing was called? Under the agitator? Im fairly certain my washer like sucked in some clothes and they destroyed that part but I have no idea what it was

[@ericinalaska7648]

Was it a washer? Or cover? Or? Is yours the same model as the one in this video or other?

[@dantesprophet9612]

@@ericinalaska7648 Washer. Same model I believe.

[@ericinalaska7648]

@@dantesprophet9612 If you look in the video description of this video. I have links to the parts I had replaced. If that isn't what you're referring to perhaps it will show other parts that will help.

[@deliaaranda6917]

Mine is a lil different model 240s5, it looks like it has a nut or bolt in the center

[@ericinalaska7648]

Yep. Possibly the most common set up. Going after the nut in the center under the fabric softener cup is how I discovered there wasn't one on this model. And then after sorting out how to come at this version. Figured it would be worth sharing the moment of enlightenment. Sounds like you got it though.

[@king_invictus]

Is there a link to part 1?

[@ericinalaska7648]

Are you referring to the parts I used/replaced. Here are the links for the two parts I purchased. www.amazon.com/gp/product/B00DM8LVDM/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&psc=1 www.amazon.com/gp/product/B00DZU9LA2/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&psc=1

[@king_invictus]

@@ericinalaska7648 thanks!

[@ericinalaska7648]

@@king_invictus Thank you. I added those links to the video info/description as well. Thanks for the heads up on that.

[@davidbarr707]

Thank you. Thank you. Thank you.

[@ericinalaska7648]

Glad it was of help. Thank you as well.

[@olandobobb8968]

What if it's not spinning and the water leaking right back out of the drain line

[@ericinalaska7648]

Leaking? Or draining? Draining occurs during the spin cycle.Thats all basically controlled by the dial which is kind of like a timer. After sitting and not spinning and the dial gets to the drain cycle. Its still going to drain. Leaving your clothes much wetter because it didn't spin. But if it's leaking? Thats another story.

[@larryg.9187]

Thanks for relieving some anxiety about removing the agitator on my Hotpoint... Of all things, here in mid August, the ants have decided there must be something tasty inside my washing machine ! In particular it seems, they have focused on under and inside the agitator ... They attacked my shower last month... So maybe its soap particles ? ... Anyway, I figured, if I remove and clean the heck out of it, that it may discourage those pesky explorers ? ... I tried running on low, with lots of bleach... But ended up with a giant 'bathtub ring' of dead ants on the tub, about eight inches wide... 😖 ...

[@ericinalaska7648]

Well glad it helped. Im gonna suggest the possibility of them seeking out the tide pod challenge? No idea. Vinegar erases the scent trail they all follow to a target though. That I know.

[@larryg.9187]

@@ericinalaska7648 Well, I was able to remove the agitator, and remove a lifetime of built up soap, soap crud, and calcium from inside the agitator, and from where it attaches... And even ran a rod through all the holes to be sure things are clear... Was a much needed maintenance chore ... Best regards 😁 ...

[@ericinalaska7648]

@@larryg.9187 Never hurts to do maintenance.

[@timtoontyme91]

Thank you SOO much.

[@ericinalaska7648]

You're welcome! Hope it helped and it works out for you.

[@1divemaster1]

Wish you’d showed how to remove top of machine prior to repair.

[@ericinalaska7648]

Unless you're going further. Doing other repairs. Its not necessary. I was exploring and those panels were off to evaluate other things. That was just the state it was in when making the video. Its been a while but I may have mentioned that in the video. Maybe not. Other than for safety, unplugging and shutting off and disconnecting the water if your gonna move the machine for better access you should be able to do this without any other disassembly. Open the lid. Pop out the agitator as demonstrated or discussed and that will expose the parts underneath.

[@1divemaster1]

@@ericinalaska7648 ok thanks.

[@ericinalaska7648]

@@1divemaster1 Sure thing. Good luck on your mission.

[@ashy6328]

THANK YOU

[@ericinalaska7648]

Hope it gets you where you need to be with it.

[@LauraPonce-db8rq]

Can't remove the plastic cap to get the screws off

[@ericinalaska7648]

This model does not require that. Some do. But this particular model does not. You simply need to tug on the agitator from the bottom to get it to snap off.

[@EasterIslander13]

Can't get dome off that is the part that I need help with

[@ericinalaska7648]

If you have this same model. There is no need to remove it. In fact its in there quite snug with either adhesive or maybe softener build up. Id say adhesive.Thats the mistake I made and I think I babbled a bit about that. If you are working on a different brand or model that holds the agitator on with a nut then yes. If so you should be able to work it out grabbing a fin with a pliers without much problem. Many other models require that. But not this model. Hopefully that helps?

[@olandobobb8968]

I have the same wishing machine not spinning

[@ericinalaska7648]

Does it sound like it should be? Making all the same sounds when it goes into spin cycle but the tub doesn't spin? Does it agitate? Check that nut. Under the agitator. If that's not it Its hard to say without looking at it. If the tub is tight. Unplug and shut off and or disconnect water. And tilt the machine in a manner that will see if you have a worn or broken belt. Heavy loads can cause it to ware over time. If your belt is broken. A new belt can be found online easily by searching for your model # drive belt replacement. About $20. Thats another poss. Its always a bit hard to troubleshoot with partial info online but hopefully that's of some help. Those would be the first two things I look at first.

[@LauraPonce-db8rq]

Can't remove the plastic dome

[@ericinalaska7648]

This model does not require that. Some do. But this particular model does not. You simply need to tug on the agitator from the bottom to get it to snap off.

[@halliking9406]

I can’t get the agitator out!!!

[@ericinalaska7648]

Is it the same make or model? If so, It can take some strength to pull or pop it loose. If its a different brand or model. It may have a bolt or nut holding it on under the softer cap assembly.

[@twistthrottleatv3504]

Thanks lol took less than 30 seconds to complete the job👏🫵🪨

[@ericinalaska7648]

Good deal. Sounds like it took longer to watch the video. But mission accomplished. Glad it helped.

[@robertborglund5783]

Thanx man, you just made my wknd.

[@ericinalaska7648]

Glad to hear it. Always good when a plan comes together.

[@elsagaped4622]

thank you, sir! i am trying to clean the exact same model and was on the verge of prying or drilling that cap.

[@ericinalaska7648]

You are welcome. Yah I learned the hard way and that was part of wha I felt worthy of sharing. Glad it was helpful.

[@andycraig6521]

Super helpful!! Thank you!

[@ericinalaska7648]

You're welcome! Hope your able to complete the mission.