Hoverboard Wheel Extra Axle and Xiaomi Front Suspension Project

Basic tutorial on how to add an extra axle to a Hoverboard Hub Wheel and fit it to a front Xiaomi scooter suspension.
Note that this tutorial cannot be considered a standard to be followed, but an open source of inspiration for your own E-Scooter projects.
Please see below the parts used in this project and where you can find it to buy.
Rear Bicycle axle: www.ebay.co.uk/itm/2545814618...
Xiaomi Front Fork Suspension: www.ebay.co.uk/itm/203113341722
Thanks for watching and do not forget to subscribe!

[@Morocco_choha]

thank you this video its important for me thanks again

[@Attic-Toy-Design]

No problem! More videos will come soon!

[@Flo-mb9zg]

ich habe ein Hoverboard Motor der Wirt bei 36V 40A 70Grad heis wen ich 72V 20A verwende wird der dann kälter ?

[@mroga5061]

Nice build. I American about to do same. I am thinking of adding the hoverboard wheel to a fat wheel. Its gonna be a front wheel drive.

[@Attic-Toy-Design]

Ok! I suggest you not going more than 8 inch fat tyre, as the Hoverboard hub motor is not that powerful only reaching 350 watt power peak, as the motor performance may not be as you expect. Better if you make a 2WD project than using only front wheel to drive your scooter…

[@AndreyKIB]

@@Attic-Toy-Design про 350 ватт вы ошибаетесь, этот мотор выдерживал у меня 2,5 киловатт

[@Pan_Borsuk]

I'd like to suggest recording horizontally, is more watchable on computers. You have some interesting ideas. Nice work, keep it up. I plan to make offroad scooter using 4 hoverboard motors, they're quite cheap.

[@Attic-Toy-Design]

Thanks buddy. Actually I just realised my mistake recording horizontally when I upload the video…🤣🤣. I’m improving it…

[@winloc3079]

💪💪💪💪

[@Flo-mb9zg]

Hast du Probleme das Wasser in den Motor Leuft ?

[@Attic-Toy-Design]

Ehrlich gesagt habe ich es noch nicht getestet, da ich das E-Scooter-Projekt noch nicht abgeschlossen habe. Aber ich denke, dass es unvermeidlich sein wird, dass Wasser in den Motor gelangt. Ich stimme Ihnen zu und werde dies auf jeden Fall berücksichtigen. Aber vorerst werden wir an sonnigen Tagen E-Scooter benutzen. 😉

[@TheVcasf]

I had to subscribe after watching your videos and seeing how you reply to comments. thank you I was thinking of using a 350w hoverboard motor as a mid drive motor for a recumbent trike. I now understand it's too weak. I hope i got that right. I was hoping to take my dog with me ;) Would it be possible to use two motors on a trike setup? thanks again

[@boasnovasonline8764]

(Brasil) Friend help me with a brushed controller d 30 vts 500w 28 A. XUN brand. I don't know how to connect this device, on the accelerator with a contact key, this accelerator has 5 wires (On Throttle Socket: Green, Black and Red) (separator: 2 wires; Yellow and blue.) This throttle has a motorcycle key and battery indicator. on the brush controller there is a white socket written: (Derailleur) in the colors green red and preto. I already know it's the accelerator but what about the two yellow and blue wires???? where can i plug it in?? we have two blue wires in a white socket written lock two blue wires written lock; what are these two wires for?

[@KevinSanchez-ts4pr]

Is it a thumb throttle or a twist throttle? If the new accelerator comes with 5 wires did your old one not have 5 wires also?

[@KevinSanchez-ts4pr]

It’s kind of hard to ignore the fact that you welded with open toe sandals, but I mean who needs the skin on their feet right?🫣

[@Attic-Toy-Design]

That’s true! My bad…health and safety zero…next time I will improve a lot of thinks, including video quality.