How does the Daly BMS communicate with the DEYE inverter

[@dalybms666]

‼Error correction: B- at 1'07'' in the video was changed to B+

[@Bellissima101]

I have 560Ah DIY LFP battery pack connect with Deye 8kW.I try to config this interface board by following your step and they work together very well. Thanks. :)

[@roberthinterberger1182]

Perfect ! Now for Growatt SPF5000es Inverters .

[@alberdellbruegge7901]

where did you connect the PC to the interfaceboard? You dont show it!

[@GraveWarrioR]

Hey there, can we have type of like "best practice" Setting swith Daly to Deye? I have smart BMS 250 and 2 pcs Deye 10k inverters. If i do as shown it works, but the system seems not to know kind of a charging curve. it will not reduce charging current at the upper or lower end. So the Battery pack gets pumped 5kW until the first cell reaches limit, then stops. Then the voltages fall, most cells would have capacity left and they are really unbalanced then, so active balancer needs a lot of time to get this fixed. Do you have any parameter recommendations to get a battery friendly and safe charging curve?

[@Anton-dl7me]

Do I need it for 2024 models with Bluetooth, mobile app and the output for RS/CAN?

[@sanitarcho]

Perfect ! Now make the same clip but for Growatt 5000 Inverters :)

[@bernd3862]

Can u help me? I do all steps from the Video and it works, but i have in the Deye Inverter every two minutes a Jump from 12% to the real % of the Batteries. I don’t know How…. Do u Use an extra Network cable for the RS485 Connection? I Use an Original Patch cable from PC… Thanks

[@masfactum]

Which cable and which slot is used to transfer the information from the BMS to the interface board?

[@jiriwiesner9464]

Hi, I can not see Deye inverter in mobile Daly app as protocol for RS485,could you help please?

[@dalybms666]

Dear Sir, feel free to contact:[e-mail] whatsapp: [phone]

[@mflo1970]

Una pregunta al estar conectados 2 bms en paralelo si ocurre una incidencia en un banco el otro sigue funcionando o se corta la carga y descarga de ambos?? Gracias

[@anandsrivastava3954]

sako sunpolo 6 kw connection with daly 100 amp energy storage bms ? and i have bought it from Amazon so i have no idea

[@MrBlackpanther87]

Is the interface board required only when using more than 1 batteries in parallel? Or it is required for even 1 battery to communicate with deye inverter over CAN or rs485?

[@dalybms666]

It is better to use a interface board when connecting inverter , no matter one or more than one battery pack

[@joselitodesotto455]

Where to connect the wire of interface board

[@GraveWarrioR]

​@@dalybms666 whats the Advantage of doing so? IT would bei very helpful If we wouldnt have to als for every Detail (and get answers to only half of the questions). Just some Info what the direct can/485 ist used for, what the Interface baord ja used for, how you can Connect it (to which Boards) and some information Like why do we need Interface board If BMS has can Port. Does interface board have any Advantage e.g. as overvoltage protection ?

[@yannickbouhier9951]

where to buy interface board , nobody sell ?

[@michalb5100]

HI , Hello . .Unfortunately this protocol did not work , you can not connect to DEYE ! I will ask for the phone number of DALY technical support ? Because after changing in PC Software 2.1.8 I changed to RS 485 PROTOCOL and to DEYE PROTOCOL , while in the application this change does not show ! The inverter does not connect to the DALI BMS ! I will ask for info to contact DALY ?

[@HeriJaya]

my deye + daly bms 16s 100ah but cell by cell not detect

[@HeriJaya]

and then.. not detect at esp32 uart

[@electricalpowerengineering9332]

Please do the same for voltronic inverters

[@joselitodesotto455]

Is the interface board will be connect to lightboard of Daly bms port

[@dalybms666]

yes

[@joselitodesotto455]

My friend, my interface board already lights up but there is no battery state of charge indicator. Do I need to set parameters first using rs485 communication. Thanks for your response.

[@nunoribeiro9259]

Hello. Can you give me some help connecting BMS to Goodwe GW5048D-ES? tried everything 😒

[@dalybms666]

Dear sir, you can ask salesperson for the wiring diagram

[@yusonvlog]

how to connect board interface to bms daly 48 volts 200amps 16s

[@dalybms666]

Dear sir, you can ask salesperson for the wiring diagram

[@hendersonsobers396]

@@dalybms666 Can you post the link to the wiring diagram?

[@victorhernandez3110]

@@hendersonsobers396 Please!

[@GraveWarrioR]

​@@dalybms666very poor information strategy here