How Durable is Siser Brick 600 HTV? How to Properly Care for Clothing Made on Heat Press & Vinyl

[@AlohaScreenDoors]

Great video, great content, thanks for sharing. I have a shirt, white brick which I am seeing some gray on one of the letters, my shirt which has been washed a lot and still solid!🤙🏼

[@ikendoitdotstudio]

Thanks Will. Just trying to keep the video train moving! 🚅

[@mydtfprints25]

The brick 1k is also a bomb! 20 washes and it's still holding like you just pressed it yest.

[@ikendoitdotstudio]

I'll need you to send me some cause I haven't been able to find it in the US

[@mydtfprints25]

@@ikendoitdotstudio No can do, you're too far from my place. Try Siser Singapore.

[@oniwindeben4332]

Nice content Bro, can please leave details on cut force, blade depth and good cut speed for the brick 600. Thanks in anticipation

[@ikendoitdotstudio]

I went over my settings in my other Brick 600 video, make sure you check it out 💫

[@oniwindeben4332]

@@ikendoitdotstudio Aiit thanks

[@oniwindeben4332]

Nice content Bro

[@Elstackobenbey5]

MEGA EVIL: REVELATIONS COLLECTION EPHESIANS 6:12 HEAVEN N' EARTH CUSTOMS T-SHIRTS#vinylpeeling Part1 kzbin.infoPrD2T8JTazI?si=brjgx-J3VzGv_D17 kzbin.info9QxV_uFUFlA?si=K7qqHBkMQHFCFlFZ kzbin.info3j_1wmUXixE?si=M43KFnvBQ4VU5qdC

[@andrewmclean1988]

Hello, I'm new to all this, I'm currently messing around with different fabrics and I've found a really nice tee but it's 56% viscose 40% nylon 4% elastine is something to avoid when printing? Especially with brick? I'm not a fan of cotton 😅

[@ikendoitdotstudio]

From the composition I'm assuming this is a light synthetic garment so I would avoid using brick. You can always test it though and see how it comes out though if you're curious!

[@caknelson2254]

..Hey boss.my brick is easily "flaked" by nail.Is that supposed to happen? thanks.....How can I avoid that? Maybe im better off with silicone?

[@ikendoitdotstudio]

@@caknelson2254 not sure what you meant by it flaked. Like it fell apart or it didn’t apply properly? I’ve also shown in this video my shorts where a piece of edge slightly flaked off but that’s also cause I wore and stress tested the shit out of it. Normal use wouldn’t get to that point

[@chuch83]

When you keep pressing Inside Out is it that the same amount of time as the right side up?

[@ikendoitdotstudio]

Ya I do it for the same amount of time, around 20 seconds!

[@Puppetlesss]

What were ur heat setting I had some lifting re pressed and still issues however I think it’s bc of the garment it was sun dyed and may have had something on it that didn’t let it stick - it was 80 -20. Cotton polyester blend 400 -450 gsm shorts

[@ikendoitdotstudio]

Settings are in the video, what did you press it at? Unless the dye wasn't fully washed off the garment then there shouldn't be any problems with the adhesive sticking onto the surface

[@Puppetlesss]

@@ikendoitdotstudio yea I watched the video but missed the settings do you know what time stamp it was ? I used 320 for 20 seconds that what’s the instructions on the vinyl said

[@ikendoitdotstudio]

@@Puppetlesss I do 310 F 20 seconds on front, 20 seconds flipped inside out with a teflon sheet. There's a good chance the dye is causing the problems with the adhesion if it wasn't washed off properly