“How I Make Angle Cuts, on the Subwoofer Boxes That I Build.

[@BudMasta]

These types of videos are invalueable. Hard to google specific answers and this is exactly what i'm looking for and a lot of under seat guys are too.

[@210Designs]

My man 👍🏽 I’m very happy you were able to find this bud useful in your builds bro. And you right, most people wanna charge or take it to the grave with them. We all learned from someone and should keep sharing the knowledge 🤟🏽 Thanks for watching and your comment!

[@Carlosm02tx]

Fr man I’ve been looking for something like this video and I’ve been looking for a month before I found this on KZbin

[@Alpacalover_123]

Dame brothers all these years I'm doing it all wrong..now Thanks to you every time perfectly fits..myself and my wife very happy I do its..thanks you...always learning something new every day....

[@210Designs]

😆 🤝 so happy you and your wife found this vid helpful. Your both more than welcome! Thank you for watching and the support 👊🏽

[@reffdogg]

Man, thank you for this video. I am new to using a table saw, and spent countless days trying to get this right. I’m excited to use your method tomorrow!

[@210Designs]

That’s what’s up bro 👊🏽 Glad you found this vid helpful. Hope your build is a good one. Thank you for watching and for the great comment!

[@reffdogg]

@@210Designs does the top require the angle to be cut? Or should it be ok at 90

[@210Designs]

@@reffdogg Yessir, all edges are cut at the same angle in order for everything to lineup.

[@reffdogg]

@@210Designs happy to report my box came out perfect. I’d I could post a pic I would.

[@210Designs]

@@reffdogg Heck yea 👏🏽👏🏽👏🏽👏🏽 congrats bro! No pic needed, just glad it worked out for ya!

[@UOAPlays]

I'm glad I watched this first. I was about to go about this the dumbest way imaginable lmao

[@210Designs]

@@UOAPlays lmao🤣🤣🤣 I’m sure you would’ve got it figured out bro. But glad this vid was able to help give another way to get them cut. If you have any questions, I’m on [e-mail] for quicker responses 💯

[@loudjunkey4206]

You make life of a builder so much easier thanks for that simple but amazing trick

[@210Designs]

loudjunkey 420 - I try to always share what knowledge I know, when it comes to building the enclosures bro. I want to keep this craft alive, even when I’m gone 💯

[@miguelamigo6030]

Great video

[@210Designs]

@@miguelamigo6030 Thank you man 🫡

[@MrWhytboi]

Videos like this help out new builders a lot and help prevent injuries or wasted materials... good vid bro

[@210Designs]

MrWhytboi - Straight facts homie! Glad I’m not the only that sees what why I do what I do 💯 Good looking out 🤙🏾

[@johnsteger]

That's a sweet trick with the saw

[@210Designs]

John Steger - Glad you liked it man 👌🏾

[@SteveDavisCarGuy]

That saw cut like butter

[@210Designs]

Man I love it 👍🏽

[@madcook1936]

A true craftsman you are sir 👍

[@210Designs]

The Beige Wonder - Thank you bro 🤙🏾

[@psementalist]

Bravo excellent nicely done well built build up box very impressive

[@210Designs]

PSE Mentalist / Much appreciation bro 🤙🏾 and thanks as always for the support.

[@CustomAudiobyJD]

I tend to draw my line for my angle, and brad nail tack a straight edge piece along line and run flush trim bit after doing a rough cut

[@210Designs]

Joshua Drefs - And that is another awesome way to get that crispy angle bro. That’s badass!!!!!

[@countryboisavage]

Pure art

[@210Designs]

Realdude rec - I’m trying homie, thank you!

[@jcook8191]

Awesome tips!

[@210Designs]

Glad you liked it 👌🏾

[@lambertoparulan5495]

Thank you 210 Designs!!

[@210Designs]

Lamberto Parulan - Anytime man, my pleasure 👌🏾

[@jameskyser9423]

Nice and easy trick thank you sir

[@210Designs]

James Kyser - Thank you and I hope it helps man 👌🏾

[@87ChevyCaprice]

Thanks for sharing bc i been having problems cutting angles💯💯

[@210Designs]

87 Chevy Caprice - That’s what’s up man. This why I post my builds, to help shed some light, for the next builder. I may start posting more of these “How To” vids in between my builds. Thanks for watching and leaving the comment. I post more frequently IG @210.designs 👌🏾

[@DIYAudioGuy]

Very nice! I've been thinking about building one of those microjig sleds to do this.

[@210Designs]

Thank you and that sounds like a great idea man. Will definitely keep your angle cuts crisp and even.

[@1badhoekaren903]

Love it bro I was waitin for this one

[@210Designs]

William Kisepi - Glad you liked it man! Hope it was helpful to ya.

[@TSCNMALKABEIWN]

Thanks for the knowledge. I'm confused though cut where you needed the smaller piece under. I'll watch it a few more times.

[@210Designs]

Thanks for watching 🤝 What confused ya bro and I’ll try to explain it 👌🏽

[@cicero2794]

Nice video...Thank you!

[@210Designs]

Your are very welcome. Thanks for watching.

[@SteveDavisCarGuy]

The irony. I need this for Jrock box 😂😂😂

[@210Designs]

😄 Did you get his measurements?

[@kars4me2]

Awesome thanks for sharing

[@210Designs]

Anytime bro, that’s what we do at 210/Designs. No secrets ova’ here 😆

[@PoppaTInstall]

More ammo for my how-to's. I learned these crispy angles from you early in the game. Good teaching. I'm always learning from you bro!

[@210Designs]

Poppa T - I really appreciate that man, coming from you. Your seasoned is this car audio game, like me. Much respect as always. I figured you’d like these crispy angle tips 😂🤙🏾

[@Bigislandguy]

Thanks for tips

[@210Designs]

Anything my friend 👌🏽

[@jaz97]

Word up in them cuts!!

[@210Designs]

jaz97 - Thanks bro! Glad you liked it and hope it helped.

[@ljones7856]

Before i get to this step, would you add to avoid losing that inch of volume. Im new..😮

[@210Designs]

Yes, every inch counts on these wedge type enclosures 👍🏽 Thanks for the great question. If you need a quicker responses or have more questions. Feel free to message me on IG instagram.com/210.designs?igshid=YmMyMTA2M2Y=

[@ljones7856]

Will do. I have more questions. 🤔😁

[@derekthomasgriffin]

Hell yes 🙌

[@210Designs]

Thank you!

[@comedyworldwide7420]

Will you do a 2 15 sealed box build plz

[@210Designs]

jb so litt - Here’s a sealed box I built for 2-15” QPower subs. I’ve got several more sealed box builds on my channel as well. Check them out when you can 👌🏾 kzbin.info/www/bejne/fH-shWh_qsp0hZY

[@TaylaFam]

Would the top piece of the box lay flat on those angles? And then just trim off the excess with a flush trim bit?

[@210Designs]

No sir. You would be to cut both ends of the top piece (baffle) with those same angles. If you done and try to use a flush trim bit, it will cut back into the top pierce (baffle) edges, until the flush bearing touches a surface. Hope that helps bro 🤙🏽

[@TaylaFam]

@@210Designs okay so that top piece is gonna be an angle cut on each side and should fit in between or on top of the box? Hope that makes sense what I’m asking

[@210Designs]

@@TaylaFam - Yes, the top piece fits over the two angle piece, not inside 👌🏽 Click the link below and skip to 1:38. It shows the top piece setting I place, with the top/bottom areas cut to the same angles. Let me know if have anything else bro 👍🏽 kzbin.info/www/bejne/fJKxqZmXpNCGnqc

[@jesusahumada794]

Is there a certain program you use to figure an enclosure or how you figure the size of the box needed. I can build it I just can't figure the sq. in. or what not. I asked you on another post of you can help me with dimensions of my build but didn't hear a whole lot back from you, any help would be greatly appreciated, I'm sure won't be as good as yours cause your boxes are fire bro.

[@210Designs]

AZ Coues Hunter - I’m sorry for not getting back with you bro. My bad! I’m am very forgetful and miss a lot of emails and social media messages. If you gave my email, shoot me a detailed message. If not it’s: [e-mail]. Best way to get ahold of me is on my (IG @210.designs) I use term pro to figure mine. I also use (the12volt.com) and (reaudioboxcalculator).

[@fernandoh.2609]

Where do I get the wood from ?

[@210Designs]

I buy my MDF from Lowe’s and Home Depot 👌🏽

[@jcook8191]

How do you figure out airspace with complex boxes ?

[@210Designs]

I try and simplify them as much as possible. If I have a box with multiple different angles, I separate them into squares, rectangles and wedges. Then measure each individually. Once I get each internal cf, I add them together. Keeping in mind I’ll be off a little, so I deduct accordingly. You just wanna get as close as you can, but it’ll never be perfect. Think of it like playing horseshoes 👍🏽

[@jcook8191]

210 / Designs thanks 👍🏻

[@Jeepjones85]

Thanks!

[@210Designs]

Your more than welcome 👌🏾

[@jayr8062]

What’s the purpose of having an angle box? Does is sound different than a cube box or the same?

[@210Designs]

The main reason for an angle box is for fitment in the vehicle. Most truck boxes fit under the seat and will require “angle style” subwoofer box. Some people build angle boxes, to give it a more custom look 👌🏾

[@danwhitaker9168]

You also get more air volume with an angled box.

[@triggah1435]

Why not use the digital angle finder?

[@210Designs]

That’s a another good way to find your angles as well. I wanted to show people another way it can be done, if you don’t have that specific tool 👌🏾

[@criaderovargas2323]

I have 2014 GMC Sierra sl I have 2014 GMC Sierra SLE double cab I am having trouble to build a box do you know the measurements ford that or video

[@210Designs]

Acura Rsx - Sorry to hear that man. No I sure don’t have those measurements.

[@criaderovargas2323]

How much do you charge for Build one for my truck

[@210Designs]

Acura Rsx - My truck boxes start at $250 and go up from there. Pricing changes, based on: wood type, box type, fabric used and degree of difficulty. Currently I’m only setup to build locally.

[@onewheelup]

i like to just get some scrap pieces and practice getting that angle right on them,i have tons of scrap,and also instead of putting the ends inside like you have them,on a wedge box where i have to cut the ends with a jig saw i decided to just put them on the outer ends,that way they dont have to be perfect,just the top and bottom piece with a 45 or what ever,man i hate these damn small boxes,i hate building them,im doing one for two sa 8's then after that a box for one nsv4 18 inch,so that will just be a huge easy box,so i will spend a lot of time and really make it look nice,hate small truck boxes haha

[@210Designs]

Yessir, that’s definitely another good way to do it for sure 👌🏾 I use to hate truck boxes at first, but now have gotten so use to building them, it’s not that bad. Only issues I have is when the customer wants to force-fit subs in one 😆 And with the larger builds, yes way more room to work with 🙌🏽🙌🏽 makes the build pieces easier to work with. You gotta post these bro 👀👀👀

[@triggah1435]

Use a digital angle gauge. So easy.

[@210Designs]

Yup, that’s a great tool as well 👍🏽

[@scottiffanimccord1509]

Can you show how you cut the face to thx.

[@210Designs]

Not sure I understand your question . Will you explain it a little more for me, thanks 🤙🏾

[@scottiffanimccord1509]

@@210Designs The baffle, do you cut them on your table saw?

[@210Designs]

@@scottiffanimccord1509 - Yes, I use a table saw to cut all pieces and angles.

[@jordanhernandez3048]

Are you in San Antonio?

[@210Designs]

Jordan Hernandez - Sorry bro, but I’m located in Oklahoma 👌🏾 The 210 confuses a lot of people.

[@jordanhernandez3048]

I need a box like that for my truck trying to get someone else to do it but I guess I have to do it now 😕

[@210Designs]

Jordan Hernandez - Sorry about that bro. Think there’s a guy in the Texas area building great boxes. He’s on instagram @ “Kast” something. His last name is Hammond tho. You might try and hit him up 👌🏾

[@EvoSGooD]

I got it, need to spend a few hundred on a table saw 👍.

[@210Designs]

😃 thanks for watching bud 🤙🏽

[@asherdie]

Some simple math and a protractor kids. Or cut till it fits.

[@210Designs]

That works too 🤙🏾

[@hinojosaleeroy]

Looking for a box Design for a 03 gmc 2500hd for 2 12in subs any help u can give me anyone plz

[@tks7393]

Just use sketch up and you’ll know the exact measurements to set you saws at.....

[@210Designs]

Yup….that’s another option 👌🏽

[@vinster1000002]

I know it was probably one time or you were being careful but using a table saw with long sleeved tops is risky business brother

[@210Designs]

😆 Yea, you are definitely right bro. A definite no-no for sure. My old shop teacher would be rolling over in his grave if he saw it 🤦🏽‍♂️

[@RelentlessLegacy2020]

answer = eyeball it

[@210Designs]

Yea, that works to 🤙🏽

[@darnellsprmla47]

It's that simple, just go to the Stodoys website and enter the world of woodworkers.