I use a polisher with a bottle brush but I would not do it inside that garage Outside away from everything. Brush on the stripper let it set for a few minutes then rinse it with water and dry it off. then use a woven bottle brush and a polisher THen recoat with stripper. after that the scratches in the paint allow the stripper to penetrate and the next time it is about bare metal. Does not scratch the metal below either. only removes the paint and leaves nice clean metal below. Then sand off the remaining paint with a da. Done I can do a whole car in 4 to 5 hours. complete. and I am talking 5 to 6 layers of paint. in one shot.
@RatsnestHotrods5 жыл бұрын
Thanks Mike. What is a woven bottle brush? I googled it with no luck.
@@RatsnestHotrods it is actually called a twisted cup brush Harbor freight has them they work wonders. you can strip anything in seconds. they have a set of them I also use them to strip wheels. Does not damage the metal at all. just removes the paint in seconds.
@RatsnestHotrods5 жыл бұрын
Perfect thanks Mike! Love ur channel Sir!
@garrymullins80104 жыл бұрын
This is the best instructional video I have seen on paint stripping with chemicals, Thanks.
@garrymullins83934 жыл бұрын
Garry Mullins What brand of stripper did you use?
@RatsnestHotrods4 жыл бұрын
Master Pro from Oreilleys. On of the commentors said the Rustoleum brand is better but this stuff worked well. Good luck!
@jasonstevens59265 жыл бұрын
Nice Tip with using the plastic to hold in the chemical. Nice to see the Tech wearing a PAPR system. This Aircract stripper is no joke so play it safe when using...
@joelgomez58065 жыл бұрын
ive used paint stripper once & i got side effects from that stuff, all because i didnt wear a respirator protector
@royboy47415 жыл бұрын
I just use this stuff the first time yesterday extremely impressed.
@deankay44343 жыл бұрын
In 2017 at the home improvement stores, I notice the price started going up, yet a milder stripper for varnish from the same company was being offered. It was an “Ouut-Ohh” moment. I bought a gallon almost every week then started getting two. I saved about $100 as the price kept going up. But I am doing an older truck that is painted inside. I think the cost to produce “Methylene Chloride” was being phased out or the concentration was going down, if you read the cans. I learned a lesson a dozen years ago with a 6 gallon metal bucket of 5 gallons of “CRC” carb cleaner. It finally ate the bucket. I got 4 O-ring seal 5 gallon buckets for free at a fast food placed, just asked the manager. I poured every can I purchased into the pails, a little glue to hold gasket still and a 2 X 4 and hammer is my stash, after a hammer was used to seal the lid. Others had said that a layer of wax covers the top, but the plastic speaks for itself. I do like your air-supply helmet I hope has an activated carbon filter. It is very mobile on your belt so battery & fan must be part of the assembly. Good for you. The government is taking away our freedoms little by little. Less good chemical, more expensive and less effective. I got tired just watching you work that stripper. Wow. I was watching to know what some use to neutralize the final wash. I feel like you...”Put water on metal”. Ok, but air dry it and 80 grit the entire surface, if you can still walk. Nice project, nice video. Hit like and subscribed already. Blessings as that two step ladder is killer on your legs too. Thanks!
@perkypeanut096 жыл бұрын
I'm about to start this process tomorrow on a 1982 caddy fleetwood hearse! Great video! Love the music!
@RatsnestHotrods6 жыл бұрын
Badass! Good luck!
@ryanho70335 жыл бұрын
Awesome video man. Got links to the music?
@recnepsgnitnarb65306 жыл бұрын
Great video. Thanks for the tips. I'm getting my '72 Chevy C20 ready for paint.
@RatsnestHotrods6 жыл бұрын
Hey Spencer! Thanks for watching! Sounds like you have your work cut out for you as well! Dig the old C series trucks! Have a good one
@TheOpenAirGarage6 жыл бұрын
The plastic makes it stat moist longer. Nice explanation.
@RatsnestHotrods6 жыл бұрын
Well when u say it that way it just sounds wrong!
@dimitria21753 жыл бұрын
Hey I have seen that brand somewhere cause I tried the one at advance auto and the auto zone brand and it worked but mostly on the most recent paint and very little bit of the original paint but I and doing a custom 2004 caddy
@appliancedude635 жыл бұрын
Thanks for sharing. I'm at this stage now. Thanks for the tips.
@RatsnestHotrods5 жыл бұрын
Thanks for watching 63!
@pcallah34425 жыл бұрын
Nobody asked me but if you did I'd say use the real Rust Oleum "Aircraft Remover", that guy worked too hard with that "Master Pro" stuff. For those who can't read, don't use the stuff on fiberglass unless you want to wonder where your hood went.
@b.neallee70425 жыл бұрын
That plastic works great. I'm just about ready to paint my 1969 AMC AMX 390 GO PACK CAR. Do you suggest putting go pack stripes on top of the clearcoat? Would they mess up the clearcoat if I put them under the clearcoat? I watched a old film of assembly line and they put all stripes as last step in process. Thanks, Neal good work
@anthonybrennan10756 жыл бұрын
Man that's a job! You need to get yourself a Ray to help you with this mate. Haha!
@RatsnestHotrods6 жыл бұрын
Hahahahaha I do need to get myself a Ray!
@husky12324 жыл бұрын
Hello there I was interesting in the respirator your wearing can it be used for spraying 2k and is it battery powered sorry I know the videos to do with paint striper but great video thank you
@RatsnestHotrods4 жыл бұрын
3m papr versaflow painters kit
@j.r.thompson59504 жыл бұрын
I am interested in finding a dust protective device like you have
@RatsnestHotrods4 жыл бұрын
3m papr painters kit
@bctw90046 жыл бұрын
I restore classic semi trucks. Always working with aluminum with tons of rivets. I try to rough the river surface with a soft bristle drill attachment. Of course we deal with countless layers of paint as well. I will try the plastic truck on my 65 Peterbilt today. FYI do not use Aircraft Stripper on anything fiberglass!!!
@RatsnestHotrods6 жыл бұрын
How cool! Worth a shot for sure! No aircraft stripper on a Corvette haha!
@Okie-Tom5 жыл бұрын
Chris Barber , so then fiberglass is sanding only. Good info.
@deloycepaulk31695 жыл бұрын
@@RatsnestHotrodsThey do make an aircraft stripper specifically designed for fiberglass. Klean Strip aircraft fiberglass paint stripper FYI.
@bryanroupe86464 жыл бұрын
I was wanting to use this aircraft stripper to strip a foxbody project all the way down to bare sheet metal. Then I was going to coat it with shark hide or matte clear. Will this not strip all the paint to bare sheet metal ?
@bctw90046 жыл бұрын
Awesome!!! Thx for posting. I would think Saran Wrap would work as good for small areas.
@RatsnestHotrods6 жыл бұрын
Hey Chris! Yeah that would work! Thanks for watching!
@ClassicRideSociety6 жыл бұрын
I used this stuff in the early 90s on my 67 chevelle and it seemed to be pretty strong stuff. Had a nasty sting to it. And boy did it stink. Had to do it outside.
@RatsnestHotrods6 жыл бұрын
Sounds like it hasn't changed too much then!
@ClassicRideSociety6 жыл бұрын
Ratsnest Hotrods that's what I hear. Haven't used it again to compare for myself.
@donaldzimmer83645 жыл бұрын
Wondering how long you estimate it took for all the steps you took to strip the entire car? I have a 1970 Impala that's probably similar in size. Deciding if it worth doing myself or paying a pro shop to strip it.
@dateatorjr96715 жыл бұрын
Man I hate the mess that crap makes but I use it because it works and it beats sanding. I use glass bead in my cabinet. It works great on everything. I wouldn’t want that in my garage though. I have a wet sump vac hooked up to my cabinet and a bead or two somehow always ends up in between my teeth and makes a nice crunch sound.. you know what I mean?
@RatsnestHotrods5 жыл бұрын
Hahhhahahhaha! Dude I blast in my shop! Of course I know what you mean! Thanks for watching Da!
@DEUCE21516 жыл бұрын
Great job! I know you you said it has no affect on the plastic covering but how about the tape? Is it good in protecting painted parts that you don't want affected?
@RatsnestHotrods6 жыл бұрын
Hey A Alvarez! Thanks for watching! No it didn't have any affect on the tape. The only thing I would be concerned with is some seeping under the tape. I didn't have that problem though. Just use automotive paint grade tape like I did. Good luck!
@Okie-Tom5 жыл бұрын
Now I found your paint stripping video. Stripper is nasty stuff! Oh, tell me what your process is when you use your Ospho? Thanks, Tom
@jefflindsey95896 жыл бұрын
That's a job brother
@RatsnestHotrods6 жыл бұрын
Amen Jeff!
@PHARRAWAY6 жыл бұрын
nice, works good wright? I love it
@RatsnestHotrods6 жыл бұрын
Yes indeed Sir Pharraway! Getting close to 10k on subscribers over there! Don't forget about us little guys!
@PHARRAWAY6 жыл бұрын
Ratsnest Hotrods LOL no not at all
@bctw90046 жыл бұрын
We tried it on a fiberglass Kenworth hood and in two days it looked like warped board. Epic fail.
@RatsnestHotrods6 жыл бұрын
Holy crap! Good to know!
@deloycepaulk31695 жыл бұрын
Did you use the stripper specifically designed for fiberglass? A friend of mine strips glass boats with it all the time.
@chrismansker88706 жыл бұрын
great video thank you for sharing the info where do you get the glass media for the blaster dose harbor freight sell that. thanks
@RatsnestHotrods6 жыл бұрын
Harbor Freight does sell some but it is expensive. I get mine at a place called Kleenblast. They are local in Tacoma, WA but will ship if needed. I would check around for a wholesaler in your area. Much cheaper that way. Hey thanks for watching!
@chrismansker88706 жыл бұрын
nice I live in amboy wa so not to far away thanks for the information
@RatsnestHotrods6 жыл бұрын
Oh right on man! 9 bucks for 40lbs. Cant beat it.
@badmandagga5 жыл бұрын
Your in Washington?? I see luckys. Are you close to spanaway??
@RatsnestHotrods5 жыл бұрын
Yeah buddy! Parkland right next to Spanahood!
@badmandagga5 жыл бұрын
One of these days come see my impala I'm trying to prep for paint. It my first one I'm doing so pointers are welcome
@RatsnestHotrods5 жыл бұрын
I'd love to man!
@badmandagga5 жыл бұрын
@@RatsnestHotrods you got a face book ??
@RatsnestHotrods5 жыл бұрын
Yep just search Ratsnest hotrods on fb
@Coaltrain87.5 жыл бұрын
Song???
@RatsnestHotrods5 жыл бұрын
All songs from Montana Jack!
@Adamz6785 жыл бұрын
Just use an angle grinder... With a grinding wheel.. Yeah, lol
@RatsnestHotrods5 жыл бұрын
I don't get it
@Adamz6785 жыл бұрын
Ratsnest Hotrods some people are impartient and do thins, gouging the sheet metal and end up with a paint job similar to a picture of the moon... But high resolution.
@thesouthernindianabeekeepe25086 жыл бұрын
Damn, love that song. Where are they from?
@RatsnestHotrods6 жыл бұрын
Hey Troy! Seattle and Montana! This guy rips on a banjo!
@whawaii4 жыл бұрын
Good video. Once the "Auctioneer Song" started though, I scrambled to hit the like button. Usually I'll wait till the end of a video, but you got me with one of my favorite songs.