5 жыл бұрын
5 жыл бұрын
Пікірлер
@timbartley5678 13 күн бұрын
Never dot a response to my question just below this one
@Donnelly369 26 күн бұрын
Im useing the super build 4.1 have the fast 4.1 tomorrow non optiex with 2.3 tip 73 cougar using the feather fill g2 on my other job 88 corvette
@ronaldoscomazzon8345 Ай бұрын
Beautifull Bluegrass. I love Shoebox and Studebaker.
@RosscoeK9 Ай бұрын
Love the music.
@KerryJackson-kg7cs 2 ай бұрын
Lose the music
@mccoymodelcars9117 2 ай бұрын
All I’m used to is featherfill. After you block In 120 it’s easy sanding. Fills all the minor lows from surfacing. Love the stuff
@speedmon6581 2 ай бұрын
Purchased mine for doing headlamp restore. My concern, boasted a 20,000 rpm. But mine is failing out of box or something. I'm pulling what feels like 12,000 at best. Is there a way to rig up a testing mechanism to see what I'm getting out of the polisher?
@michaelvalentine629 6 ай бұрын
Why on earth ruin a nive car!
@AMCguy 6 ай бұрын
Song name?
@MarcBchannel 6 ай бұрын
I ordered that gun after watching your vid. Boy does it work good for Featherfill. The 3.0mm tip is huge. Ive seen others use smaller tips like 2mm in gravity guns or the mini pressure pot from harborfreight and they just dont build up fast enough. This gun is faster with more flow and a decent fan. I dont use featherfill that much these days. I like using Tamco 2k 4to1 layed on thick with a 2mm gun. It doesn't shrink back much and its easier👍
@gaylewhite2049 7 ай бұрын
Didn't safety chain second spring beforre lowering. he he he
@markwhite8543 7 ай бұрын
Great video, your tase in music is questionable 😅
@danno592 7 ай бұрын
You forgot the safety chain on the second control arm. Safety first !
@DavidBrady-wf6qh 8 ай бұрын
High price gun for primer? 19 dollar gun will do the same! Thanks for the video. BAD CHAD ROCKS!
@danielgause9965 8 ай бұрын
That’s you guys for the video shop just got one today and had to put it together
@rattmichards2908 9 ай бұрын
Dude. the volume change is maddening..
@RobertJones-sb1if 9 ай бұрын
It's" twodoor" despite it's spelling. Thanks for the video
@helisean10 9 ай бұрын
How could either of these primers be any harder to sand than body filler?? I call bs. I have used slick sand many times and it is a joy to sand because it is so easy and smooth. If it is laid on nicely, you can go straight to 320 or 400 grit. No way could you do that with filler or polyester putty. It makes no sense at all when people say that polyester primer is hard to sand. It is designed to be finely sanded and it is possible to paint directly over. It is great stuff. It makes big filler jobs much easier and sands like a dream.
@GregoryJohnston77 10 ай бұрын
I moded my mix mate for my drill 😂😂😂
@timbartley5678 11 ай бұрын
My question they got a primer that is in a spray can with harder in a bladder where u rupture it shake it up really good how does that compare to the other primers even though the can I am talking about pretty expensive but when u compare prices and quality I am not sure what way to go its my first project 1958 chevy fleet side
@XtremeBoomer2007 11 ай бұрын
Will this spray out reduced 10% with acetone with a 1.8 tip and those el chepo HF guns?
@philciret5565 Жыл бұрын
Thank's for your video , can you tell me where we find the rear shocks for 4" lowering. Thank's Philippe
@JohnDoe-ud2cc Жыл бұрын
You should have used lizard skin instead
@elqwan Жыл бұрын
Where did you go man? Did you finish the cadi?
@keithhall4009 Жыл бұрын
Thanks for the advice. I bought the 20lb pot from HB and the brass ball valve blew a hole in the side after shooting only three door hinges and using maybe 5lb of glass media from HF. I thought it was defective, but now I know it’s just a design defect. I’m gonna try this valve out, as I liked how it worked, and I won’t be able to find anything else for $80!
@haleyroberts557 Жыл бұрын
how do i remove the pads afterwards? I can't seem to get mine off to change it
@richardeddings7259 Жыл бұрын
What did you paint your fire wall with? I checked out in my fire wall with rattle can enamel and not balky with it wanting to out this stuff under my ss
@BigJoeWalker Жыл бұрын
Thanks for this video series!
@LgSutterby Жыл бұрын
What tool did you use to remove the stainless trim around the window? I need to pull the front and back glass on my '65 to reseal and do some rust repair, trying to figure out the trick to getting the trim off and not having much luck.
@claytoncutshall9495 Жыл бұрын
Any suggestions on buying a raw steel fender ? I bought front with no trim holes and a new 5 inch extended steel fender.
@claytoncutshall9495 Жыл бұрын
Question for ya…. How much base coat and how much top coat should be bought for a Harley Electra glide ? Getting ready to do mine. Just not sure of how much to buy.. going with tricoat. Harley velocity red sunglow.
@kenmineker4477 Жыл бұрын
I just picked up a 1964 AMC rambler American 440 that needs the trunk floor pan replaced. Can you suggest or know of anyone that reproduces a new metal pan? I'm also going to drop a 343 & auto transmission out of a 1968 AMC AMX Into it, would you happen to know if there's conversion motor mounts & trans mount made to do the swap with? Any help is appreciated
@victorjbrooksiii7963 Жыл бұрын
You need to find a V8 crossmember and the short metal engine brackets from a 66 to 69 American. The short engine mount brackets are only on American, Gremlin and Hornet. A crossmember from a Gremlin or Hornet may work. I am going to be trying to put one of my American crossmembers into a 81 Spirit. I believe Gavin's AMC had it in their catalog. Otherwise it's swap meets and clubs or if you're lucky a junk yard. Going to be pretty pricey for any 01 small body only V8 parts. Thats why so many people just weld in chevrolet mounts. I could never do that I am a purest AMC engine only. Transmission crossmember is the same for automatic and manual.
@Flyonthewall79 Жыл бұрын
Started watching this channel. I hope your ok, Havent seen you on here in 2 years. Was excited to see the Caddy finished.
@garahastings8214 Жыл бұрын
Please learn to level the volume can’t hear you talk but nearly blows my eardrums out when you go to music.
@NOBOX7 Жыл бұрын
Just remove the valve and only use the valve under the pot to control abrasive flow . best way to go . this way the hose dont fill up either
@martinolivas319 Жыл бұрын
Hey brother I’m wanting to rewire my 76 c10. I’ve already got a LS stand alone harness for my swap ,but would like to change out the chassis wiring for the rest of my truck. I’ve already got the Dakota digital gauges and all other engine components wired to the stand alone harness. I’m not currently running electric windows or locks but would like to eventually, so I’d love your opinion on what set up I could use without the overkill or too much unnecessary wiring. Any advice would be appreciated thank you.
@YarHarFD Жыл бұрын
Thanks for uploading this! How precise is the shear? Would it work well for cutting very small shapes like 1/4" to 1/2" inch?
@user-ls1eq5pe1d Жыл бұрын
Cood
@jimhiscott2918 Жыл бұрын
LED pulls a ton less current then standard bulbs. I put the kwik wire 8 curcuit in my 95 Honda Civic. Worked perfect.
@larrygriffin7024 Жыл бұрын
My friend Pete from diy auto school says it worth less to spray feather fill on the whole panel you only use it on spots you did the bodywork on. Now after the bodywork is finished and there’s metal showing spray epoxy primer to lock your work in then after it’s dry enough Flash time then spray Feather fill only in the spots you did your repairs on not the whole car or panel because my friend Pete from DIY auto school says so. Now put that in your pipe smoke it
@rafaelespinoza2209 Жыл бұрын
Did you ever install those drop spindles?
@hiepdam6262 Жыл бұрын
Music like shit too noisy
@handymanluis8 Жыл бұрын
Do you recommend that epoxy sealer?
@garyfranz1888 Жыл бұрын
when you lower it 4 inches do you have driveshaft tunnel clearance issues
@wilecatrexy Жыл бұрын
Since you had all those parts off, why not clean them up and repaint. Makes a quality job all the better.
@spenceair1972 Жыл бұрын
What kind of respirator system is that?
@robertcampbell5605 Жыл бұрын
I do body work at a high production shop. All makes and models I use this trick all the time never had an issue with paint so far.
@Imwright720 Жыл бұрын
Just curious , isn’t everything in your garage covered with overspray.
@rongamble9884 Жыл бұрын
I don't recommend either one of them quit being a butcher and do body prep the right way
@daleaxe1030 Жыл бұрын
Thanks bud