How To 4/6 Drop Your NNBS Silverado Or Sierra!Using DJM Control Arms Or Springs/Spindles&Flip Kit!

Welcome to a new step by step how to video from Proyectos Los Carnales! Today Pablo brought his HD Silverado and Angel brought his NNBS Silverado to get dropped and give us a cool video! I go over a step by step with as much detail on how to lower your Silverado or Sierra NNBS mamalona. If you have springs and spindles to lower the front you can start at 00:32. If you are doing the DJM lowering control arms you can start at 18:43. To do the flip kit lowering the rear of the truck 6/7 inches start at 08:00. Enjoy the video and if you like it Like, Comment, and Subscribe!

[@angelmeza2894]

To anyone who bought the mcgaughys kit and can’t find a way to remove the bottom bolt of the rear leaf spring. you should remove the tow hitch to have the clearance to pull it out

[@trucksonlytv9976]

Nice work!! Love that look

[@wierpkevin]

Looks great, just what I needed, thx

[@senditscott4735]

Bang bang drop gang!!!! 👏

[@cesarcervantes7527]

Very nice bro. Very detailed

[@gallo2low664]

Thanks this video help alot 💯

[@rubensalais1502]

Great video explaining everything

[@milofuentes1088]

BADASSS video well done bro gained a sub for sure

[@erickuribe9860]

Just subscribed. Nice work man 👍

[@jameshaney1237]

You are very therral with your instructions on your videos . I will be doing the same to my 2008 Silverado rcsb. Glad to see it can be done in 1 day Thanks , JD HANEY

[@StashingClips]

fire video keep it up

[@hadnotandsons9308]

nice informative video

[@boostedjrrr]

Can you use lowering springs with the drop control arms to get like a 6” front drop or do you have to use the stock ones?

[@angelmeza2894]

where did you buy the lowering spring from? i already ordered the same kit for my nnbs extended can

[@yuzettq5177]

👏🏼🔥🔥🔥

[@corridosmascabron784]

🔥🔥

[@dannydaniggaz23]

How much does the angle of the differential and driveshaft change?

[@AlejandroMartinez-iy8ry]

I see the video every time I drop my truck

[@alejandraq8799]

Had fun helping you! Very detailed! 🤓 love you 💕

[@ronieramirez4842]

How much does the truck bed weigh

[@cruzolivas6319]

If u take off the 1in block it’s 6in no? And if you leave it it’s a 7in

[@edgabrielcervantes9707]

buen video amigo eres de los pocos que ensenan como hacerlo mi pregunta cual seria el mejor metodo arm or spring o spindless cual de los 2 recomiendas para que la troca quede bien como de agencia gracias de antemano bro👍👍👍👍👍👍👍👍👍👍👍👍👍

[@proyectosloscarnales4512]

Con los control arms se maneja más cómodo como agencia y gracias

[@BassRocket]

bueno

[@alexolvera3059]

Where u guys aré located

[@santiagocisneros3002]

Where you located at pa ?

[@frankduran6062]

Hey bro i have a 2012 Silverado i have 22" on i want to lower it so the gab is not the big would this help if i change the arm controls

[@proyectosloscarnales4512]

Yea u can use lowering control arms or the spring and spindle in the rear u can use shackles or a flip kit or both with a under bed notch

[@Angel-ft8bv]

Did you install the shocks correctly on the first truck. They look upside down. Another's thing, I think you are suppose to put the upper balljoint under not over.

[@belikianza5097]

Just saw the 03 Silverado on the freeway

[@josuegonzalez9364]

Do you think you’ll have camber with just 2 inch drop springs?.. Really want to drop my truck 2/4 but don’t want to mess it up

[@proyectosloscarnales4512]

yes usually the springs give it camber you might get away with just a alignment or running a drop spindle instead of drop spring

[@jesus6353]

You think that if I get the flip kit done and drop it 6 inches alone with that, do you think I could keep my 2 inch drop shackles but just move over the bolt to keep it at 7 inches without needing a c notch

[@proyectosloscarnales4512]

Honestly it’s based big on driving style you can possibly get away with it if you do not carry heavy stuff but if you plan on carrying heavy stuff I’d recommend stock shackles or a c-notch. Worst case scenario try the 7 inch drop and see how it feels for you the stock shackles only take 30ish minutes to swap if you need to swap them.

[@jaybizzzird]

What’s your ig bro? Very detailed video, thanks

[@cruzolivas6319]

Do I have to put lower shocks? Or can u use stock ones

[@proyectosloscarnales4512]

depends how low you go they make specific shocks if you go 3 inch or lower drops use them they are made for that reason

[@jefferyknudsen4028]

Great video, can you add the stuff your purchased for the 2500 in your comments area please?

[@proyectosloscarnales4512]

The black truck got lowering control arms you can find them at djm suspension or ihc suspension

[@deez3936]

You think a aftermarket strut assembly would change the drop? My tire sticks way out and I cant get the guys to get my truck aligned.

[@proyectosloscarnales4512]

Usually the upper control arm helps with alignment issues they also make specialty upper ball joints it all depends what’s going on with it

[@patrickoshea9527]

Get off set upper control arms

[@ericmonsivaisem]

Doesn’t the ball joint on upper control arm bolt to the bottom not top ???

[@Angel-ft8bv]

Pretty sure it's bottom

[@robertcolunga6479]

Did you use the stock spindles with the drop control arms ? I put some on my truck and didn’t fit on my stock spindles. I hat to put the drop spindles so it gave me about 6 inch drop in the front and it’s to low.

[@proyectosloscarnales4512]

Stock spindles but check the ball joints on the lowering control arms because the nnbs had some trucks with aluminum spindles and some with steel spindles from factory and they have different ball joints one is bigger than the other

[@robertcolunga6479]

@@proyectosloscarnales4512 damn that might be the problem. I’ll be checking up on that soon bro, thanks for the info, I appreciate it.

[@proyectosloscarnales4512]

Based on where you got the arms they have replacement ball joints just get the opposite ones from what you have now. Start there bro 👍🏽

[@robertcolunga6479]

10/4, thanks a lot bro 🤘🏽. Great video you made here.

[@cruzolivas6319]

If I just install lowering front springs do I still have to cut the lower ball bolt to run 17s?? And can I still use that 1in block to run 6in or do I have to remove? Thanks I’m advance

[@proyectosloscarnales4512]

I believe its only for the 4 inch drop that you need to cut ball joint to fit 17s and that rear block is specific to stock differential location after the drop you have to buy a lowering block if you want to lower it more or just throw it out and have a 6 inch drop with the flip kit

[@cruzolivas6319]

@@proyectosloscarnales4512 thanks bro appreciate it👌🏽

[@cruzolivas6319]

@@proyectosloscarnales4512 I did the same thing i you u did and some how it went like 8inches it bottoms out hits hard on bumps it has stock shackles

[@ManuelSanchez-en5hp]

@@proyectosloscarnales4512 hey bro if I get new wheels in the further would I need to replace the ball joints

[@gabinotorres4622]

Do drop trucks have coils or do them take them of ?

[@proyectosloscarnales4512]

depends on which kit you run with some use new drop springs and others use the stock ones and just use lowering spindles or arms

[@lsgt5132]

Let me guess, you guys are in TX. Damn wish you were in NC.

[@2wdDenali]

Do you like the control arm drop or the spindle and spring drop more and why?

[@proyectosloscarnales4512]

Control arms they are better when it comes to alignment if you go lower than 4 inches

[@2wdDenali]

@@proyectosloscarnales4512 that's what I went with. Thanks for the very informative video!

[@proyectosloscarnales4512]

@AlteredMood Glad it was helpful and worked for you, that’s why I like doing them!

[@elwerogaming1331]

My truck bed hits my differential when ever i hit a bump what can i do

[@elwerogaming1331]

4'6 drop

[@elwerogaming1331]

4x4 08 4 door sierra

[@lorenzoflores8421]

Tienen un Instagram bro ?

[@ulisesjaramillo9019]

Any camber

[@proyectosloscarnales4512]

Not with the control arms you can always buy after market upper control arms and do an alignment so you won’t have camber when lowering these trucks

[@rezar6480]

Did you need to c notch it?

[@proyectosloscarnales4512]

You don’t need a c notch or under bed notch for a flip kit alone but if you do 8+ inch drop you do like a flip kit and shackles

[@rezar6480]

Alright brotha thank you and good video btw👌

[@proyectosloscarnales4512]

Thanks!

[@jadycarmona2668]

@@proyectosloscarnales4512 what’s your IG how do I get in touch??

[@frankieknuckles3]

Them parts got dirt all ove we them

[@Lucky_Logan]

Damn looks like that truck needs some brakes, those toros look absolutely toasted. Put some money into the brakes need major maintenance instead of customizations

[@JesusOrtiz-qp1so]

I’m surprise how good English this tacuaches speak lol

[@arod.mediavlogz]

What’s ur Instagram