HOW TO | A - Z ROOFING (PART 1)

[@gfatty9038]

Love it No fluff or over talk...EXCELLENT!!!

[@sully7233]

Actual career roofer 6 years. just a few things, great video thought it was very informative and great for DIYers definitely if you’re brave enough to do you’re own dang roof, but couple of minor things I noticed. Wouldn’t call them errors just this is my career 4 tab asphalt shingles and I’ve spent many a year on the roof. first few minutes right away the drip edge (metal flashing he installed) should be an 1/8th to 1/4 inch out from the plywood on the bottom to allow the water to have more distance when going down the roof maybe to feed into a gutter or at least away from your ply wood as sometimes the ice and water won’t seal perfectly and you have that room for error. After that the ice and water, installation was good. I do recommend depending on the slope securing the underlay alittle more with more staples or ideally nails from your gun if you intend to stand on it when you cut your ice and water back you lost me, you did overlap your paper but that seems to be about a 4 inch overlap which if you’re not using the adhesive on the top of the ice and water paper which is alittle faster to stick does make me nervous. I’d leave the ice and water paper at least a couple feet in width and then do my paper over that not worrying about the minimal size difference as the shingles will cover that so it’s unnoticeable assuming your underlay isn’t full of bubbles. Paper was good, again you’re making me nervous standing on it with so few staples but it’s on the side of a house and only a few feet up so 🧘🏻 I’m calm. Appreciate that you went over the ridge with your paper, seriously so good🤣 Did you just say you fired a guy for smacking his hand with the staple tacker??? I’ve got over half a decade of just straight roofing nothing else and I do that at least once every few weeks. Apprentices will do that a few times a day🤣 hard core man. The side flashing is interesting but I would have used the same piece as the drip edge and wrapped the corners at a 45 because if you don’t caulk that at the end of the video your plywood’s gonna get hit What are you doing with that starter??? Are you going to cut a little 2 inch strip of starter for the sides?? Why make it more difficult on yourself there? Good video. Works well for your first roof ever

[@jasonnester9514]

The weather shield has to wrap over the facia

[@jasonnester9514]

Ice guard wraps over facia 3” then drip edge smh

[@dariusjohnson9668]

This is just a friendly reminder KZbin has almost everything

[@olcotttheosophy]

☑️

[@KennysCrap]

Screw tube is a censoring shit comunist platform ..

[@SkateNateTheGreat]

Is there anything it doesn’t have? For real though.

[@Frank-wb1jz]

@@SkateNateTheGreatcrazy that I want to get into the roofing business but I don’t know anything and this video literally helped without having to go to school or wor for years of knowledge

[@booties420]

Are you a roofer in Tennessee? If You are, maybe you have some pointers?

[@tommyornothing7301]

I just started a position as an Exec Asst to the President of a roofing company with no prior experience. I type proposals for him all the time. This is helpful.

[@bigthunder7002]

This helps but manufacturers have slightly different specs on how to install depending on the product so always keep that in mind!

[@cunicularium5424]

8:45 Greatest part of the entire video! 🤣 Probably hurt a lot of little fellers feelings on here 🤣

[@TheExcellentLaborer]

Very good explanation. Thanks for sharing. I got to get back to laboring and recording!

[@Waycool247]

Yeah Man ... plain and simple. I love the tools you use. The hammer is dope. You speak clearly and that's really appreciated. Thanks

[@NWIVeteranConstruction]

If you like this one check out part 3 of my most recent roofing series. That video was much better than this and has actual shingling

[@jeffjohnson1814]

10”! Immediate thumbs up for including the joke!

[@davidw3605]

Thank you for information, would like to find someone like you in my area. Time to have my roof redone. Keep up the great content!!

[@EricV259]

I figured out my self this neat trick on making drip edge look nice and continous. Seeing drip edge like at 9:24 just pisses me off. First squish the end that goes over a bit (all roofers know this) 2nd bend the corner with the kick out a little extra with your index and thumb kinda like you wanna make a triangle bend mark. More than half the time the overlaps come out beautiful you can't even see them

[@chevytruckjerry]

Super helpful man, no b.s., to the point. Was a huge help this past week. Thanks so much 👍🏻👍🏻👍🏻👍🏻

[@NWIVeteranConstruction]

Thanks

[@daisyorpington784]

@VeteranConstruction Soo glad your video showed up! I'm always having poultry "dumped" on my place and carpentry is NOT one of my stronger skills. Funny I've been trying to build some coops to house all the animals and still haven't managed..Currently some simple in trailers I bought with boards on top..and YOU build a structure to shoot an educational video! Anyhooo...I subscribed! Hoping it's as easy as you make it look! Thanks from a Nebraska Farm girl!

[@DRAGON-ho6rz]

Muy bien explicado, gracias por compartir tus conocimientos

[@runiniscrazy]

Thank you so damn much for showing proper gutter apron/drip edge/ rake edge installtion! Literally every single roofing company in my area 45s regular drip around to the eave and all on top of felt. I've seen hundreds of roofs this year and 1 had proper drip edge installation.

[@NWIVeteranConstruction]

No problem man

[@marcelojamari9407]

Instablaster

[@DudeWhatHappened]

Because that’s how you do it, so that’s why every company is doing like that

[@bigthunder7002]

The most professional way and best imo is bending the corner as 1 piece wrapping from eave to rake. It’s a tricky cut but looks great and doesn’t leave a seam on the corners.

[@runiniscrazy]

​@@bigthunder7002I agree this looks most profesional and nice from the ground the problem primarily occurs when you install gutters on that roof. You want the gutter to go out past the edge of the shingle on the rake because there's more surface area for water to cling to so it has a stream that comes off the corner of the shingle at the rake/eave. So with the wrapped corner you have to hang gutter below drip edge, notch the back of the gutter to accept the drip, or cut the drip to accept the gutter. You could also just have the gutter stop at the drip. But I can tell you from experience that little stream that comes off the corner will dig a hole in the landscaping.

[@stevejones8486]

With the new synthetic felt you can staple just the top and bottom. Keep the staples out of the feild and no more leaks, YES it will hold you. Try it and thank me later.

[@NWIVeteranConstruction]

yea people don't trust the staples enough

[@user-ws3rw9ur4y]

It voids the warranty. Says it right on roll " do not use staples"

[@stevejones8486]

@@user-ws3rw9ur4y I never knew that, I believe you. I imagine they want you using the green cap nails..yeah hardly anyone does.

[@user-ws3rw9ur4y]

@@stevejones8486 ya man check out the installation pdf, it's on the first page page lower left after "Important" that's in bold letters. You need to use caps www.google.com/search?q=gaf+feltbuster+installation+instructions&ei=UaXvYJLyHo2utQbL3pmIAQ&oq=gaf+feltbuster+insta&gs_lcp=ChNtb2JpbGUtZ3dzLXdpei1zZXJwEAEYATICCAAyAggAMgYIABAWEB4yBQgAEIYDOgQIABBHOgQIABANOgUIABCRAjoFCCEQoAFQ-x9Yui5gnDZoAHABeACAAb4BiAH7B5IBAzAuOJgBAKABAcgBCMABAQ&sclient=mobile-gws-wiz-serp

[@felixrivera4802]

We use cap nails, it’s safer for the roofing crew

[@michelleamidon2083]

I professionally build training materials for corporations to use for educating/training employees on processes and this video is VERY well done. 👏👏👏 Keep up the great work on uploading educational videos.

[@NWIVeteranConstruction]

Haha thanks I'm trying to get better as I go. Still Struggling with the professional part

[@michelleamidon2083]

@@NWIVeteranConstruction I do the same and always try to get better as I go. Training/educating people on a process is not an easy task. I am trying to learn about roofing because my daughter is having a new one put on and this video helped IMMENSELY. If your audience "walks away" more knowledgeable then you are definitely a professional.👑

[@davidmc1489]

Would of left out the sexual inuendo...just sayin...not everyone likes the locker room lingo. Other than that was good vid..IMO

[@mchapman2424]

I can feel this guy feeling the camera watching him. And I can relate.

[@idkok1949]

This is very helpful I start on Monday I’ve never roofed before

[@NWIVeteranConstruction]

If you like this then you'll love my most recent 3 part series! It's Way better

[@michaellawinsky5072]

You are so professional you explain everything clearer!!!😉⭐⭐⭐⭐⭐⭐⭐⭐💯💯💯💯💯💯💯💯💯💯💯⭐⭐⭐👏👏👏👏👏👏👏👏

[@NWIVeteranConstruction]

i tried this time lol

[@michaellawinsky5072]

@@NWIVeteranConstruction excellent you are amazing!!!😉💯⭐💯⭐👏👏👏👏

[@daneric8089]

Thanks for showing the steps.... wish i saw this before i started the roof.. but its done.. but do I enjoy watching,, looking forward to part 2.... I should have sent you my roof sketch for questions.... i see my mistakes Thanks again... no one is ever to old to learn....

[@NWIVeteranConstruction]

Very true. Hey I break a lot of these rules too so no sweat lol

[@edwingaldamez7001]

I learned more on this video than working for almost 8 months with guy really don’t wanna teach me Now that I started practicing what I saw here they say: I taught you the good way to do it

[@cma3602]

Thank you finally a video step by step how to prep a roof

[@Joshwagonda]

Awesome video man! Something I've learned for dripedge is to slightly bend the end of your metal inward with your hand for the overlaps and it helps to keep it from flaring out, works for eves and rakes (florida mans alternative to making the 45 cut, cause code calls for a 3'' overlap on all dripedge). Code here calls for everything opposite of what your doing too lol

[@Josh-ww5kz]

It's easier if you just snip the metal a little, opposite from what he does in this video, then you can slip the underside, where the L shape is, and tuck it underneath the side you're laying it overtop. Makes it 100% flush.

[@Joshwagonda]

Josh If I got what your saying right then that would work just fine too. Where i’m from they require 3” over lap on all eve or rake metals so bending the ends is the only option

[@dacostac04]

The 10 inch joke made me check out the comments!😂

[@justanotherperson584]

Great line. “just the way she likes her men…no less than 10!!!!!”

[@stixprogaming2718]

Cool video, when I do my starter I start my gable one first and get my overhang on the side gable plus bring it down on the each so it has the over hang on the side and the eave, then I but my first eave starter too that gable starter, might sound confusing but it looks good too.

[@NWIVeteranConstruction]

i think ik what you're talking about. the actual starter and shingle part will be out thursday

[@johnkramer745]

complete noob here. i have a question. initially you covered the whole roof with the ice barrier but then around the 3:40 mark the ice barrier is only for about a foot from the bottom and then you covered the whole roof with the synthetic felt on top of that. what am i missing?

[@NWIVeteranConstruction]

Watch my video on the tear off, dry in , and put back. It will explain all. It's got around 700k views if I remember right. It's an hour and 8 minutes so you can skim through and see whatever you want

[@johnkramer745]

@@NWIVeteranConstruction thank you. that helps. will check the video.

[@yorzemog4430]

THANKS FOR THE VIDEO... VERY INFORMATIVE. TWO THUMBS UP 👍🏼👍🏼

[@NWIVeteranConstruction]

appreciate that thanks

[@rehanafridi8607]

Nice work, could you write down step by step what you do and also nail size and staple size please.

[@carlsbadroofrepair5417]

THank you for your service man

[@NWIVeteranConstruction]

Np Thanks

[@WeFindSimpleSolutions]

Great video. Right to it the right way

[@NWIVeteranConstruction]

If you like this one you'll find that my most recent 3 part series even better! Check it out. Part 3 specifically is doing very well

[@KJ7JHN]

Zach, please make a video showing how to apply underlayment to an angled hip roof. Does ice shield go over the hip? Do i cut the underlayment as it comes over the ridge to lay flat on the hip? Ive got a roof line like a typical gable, but the rake side has a tapered third side. Similar to a pryamid.

[@Garandmasthumb]

I definitely need this video I have to redo the roof that my ex-wife’s husband put on top about the shittiest job ever he didn’t even stagger the The shingles instead he made a nice straight line all the way down the roof.

[@carlosenriquez9263]

My gpa would always make me roof w him he was so harsh w me i had to learn to roof thats what i thought as a kid now being an adult im grateful for his teachings to survive and i could actually say im not useless in this world

[@buckethead1928]

I cover the ice and water with paper so it’s easier for next guy and easier to walk. Tearing off shingles from some ice and water is impossible. They become one.

[@jonbravo9278]

Was wondering about that. I have seen a lot of videos. I did my first roof with my dad in 1995. They didn't really have a lot of the underlayment they have now. I see a lot of videos where it seems to me they are either skipping steps or the process has evolved around speed and not around function or considering the next team that will replace the roof in 15 years +/-.

[@davidkempf2368]

I watch all your videos and just want to thank you for all your knowledge. But I just watched another video that instructed to put the ice and water under the drip so you get coverage on the front 2in of plywood ya or na?

[@MikeHewitt]

Great video, straight to the point! Can't seem to find part two though. It's always nice if you add a link in the description to the next video.

[@HankTheCaveman]

Here is part 2 kzbin.info/www/bejne/b3TJeJykjrmFprc

[@NWIVeteranConstruction]

wow thanks

[@5050johnsmith]

When are you getting to rafters and hip roofs along with the slats for cedar shake.with a chimney in the middle of a flot top on a hip

[@Innessphoto]

What happened to the IWS? You applied it over the entire roof then in the next clip it was gone when you installed the felt.

[@DanielinLaTuna]

He had to simulate a bigger roof. His mock roof is small enough that it is almost entirely covered by the Ice & Water shield, and installing the underlayment (“felt”) would mean covering more IWS than needed. It would give the impression that more than four inches of overlay is necessary.

[@wylandreed9797]

@5:50... You can set and trace "ANY" metal with the oils on your finger tip.

[@marshallhosel1247]

Thanks for the video!

[@olcotttheosophy]

Good

[@Soprano0913]

great video! Do you have to install a drip edge on a split level home where the roof edge runs into siding?

[@NWIVeteranConstruction]

Not specifically no, but you just cut and angle so it's tight to the wall and trim the protruding edge back and inch so it allows the drip edge to extend back, with the thick edge resting flush against the j channel

[@bojangels3545]

Had a roof repair for my grandparents. Kept saying this is how zach would do it

[@NWIVeteranConstruction]

Lmao that's crazy to think about. Thanks for sharing that

[@Mandeiros]

No less than 10 babyyy

[@gabrielmendez7669]

You should use your knuckle on your finger it’s a whole lot faster than chalk line for your starter and usually I put my first starter piece on the edge metal side then I put my starter where the drip is at that way u can put a full shingle or start your books immediately if u want a demonstration let me know. And I promise I always come out straight

[@jrcortez3366]

Thanks man this was real helpful I've been watching soft but they leave out most of the good detail section need to start the roof

[@thomaslindsey7685]

Why not use the "peel and stick" msterial over the entire wood sheeting? Could that be done and would that be better? Thank you.

[@valcty1]

Love your video's, why are some starter strips half width (skinny) and some I've seen you install full width (fat).

[@NWIVeteranConstruction]

If you're talking about in other videos I used some fatter ones..yea I preferred those taller ones but that brand quit making em and I moved towards using the manufacturer starter these days over what I prefer anyway. For example if I'm using GAF shingles on a job I'm gonna always use their starter and ridge cap as well. 3 components for the warranty.

[@KeyboardPriest]

Do cap nails help at all for ice and water & felt?

[@cma3602]

So if your doing more then what the ice and water covers and your using paper up the rest do you lower the paper to the bottom of the top laminate?

[@cma3602]

Nvm this video answered my question lol

[@Boxdude22]

Another great video!👍

[@NWIVeteranConstruction]

thanks bud

[@ehvs]

This is a great video!

[@nicholaswillis5063]

when installing starter stip along the rake are suppose to overlap or butt up

[@serg2523]

Do you have to put ice and water on the roof rakes?

[@bigthunder7002]

Looks good!

[@stingray957]

Where did you get the Hammer nail gun at????

[@ZipKickGo]

Check out the flow, love the hair dude hah!

[@NWIVeteranConstruction]

gatta cover up that bald spot lmao

[@Sean-John]

can i still use gutter apron if the gutters are already on the house im just replacing my roof not starting a new project

[@NWIVeteranConstruction]

Yes. You put it right over the back of the gutter and into it.

[@jacman6409]

Starting my roofing job tomorrow...

[@canocano5480]

Could you treat the wood under the flashing to to prevent rotting.

[@Anthony-h7d]

Great work

[@Lastangas]

i like your videos, do you have your own big company? or do you get houses from companies and give work to your crews or crew? ( like an LLC)

[@NWIVeteranConstruction]

I do my own work. 99% of the time

[@MADDOG100ful]

On the ice and water the sticky side goes down the bottom to stick your starter strip down on the Outer Edge by the gutter great video though

[@harrybotonikes]

Were can we buy that great tool hammer?great job ,big man ting,big man ting

[@NWIVeteranConstruction]

The Bostich gun? Menards has Bostich and Hitachi

[@harrybotonikes]

Top man 🏋️‍♂️

[@harrybotonikes]

Its the touch and nail..never seen that one before bruv,easy now!

[@PhilipBargeman-d2p]

Good work

[@nicedinger2650]

Great videos. Question: I’m getting ready to reroof my house. I have 4 valleys total. Do I start in bottom corner and work into the valley or shingle valley first and work outward? I’m planning on using 2 cut 5 row method that I’ve see you use. I’m planning on using closed valley method.

[@NWIVeteranConstruction]

Watch my valley video. You can do whatever way makes sense. A lot of ppl think you have to start from the valley, that's not true. I wouldn't run a big side left handed just because It's easier to do a valley from the valley. Sometimes it makes more sense to shingle a big side side up to a valley and then cut pieces into it. Once in a while.

[@NWIVeteranConstruction]

Also, if you haven't ever roofed before, and your house has 4 valleys...I can almost gurantee you'll mess something up lol just want to throw that out there. Listen to the beginning of my most recent roofing series and it will tell you why. (In part 3)

[@robertoaragon7915]

What kinda hammer is that i want one for myself

[@stevengao8345]

thanks for this nice video, can anyone tell me what is the first black layer is called ? i know the second layer is called roofing felt. thanks

[@NWIVeteranConstruction]

Ice and water shield/ ice barrier/ ice and water barrier /ice shield. Ect.

[@bigthunder7002]

You don’t bend your drip/ gutter around around the corner? IMO that’s the best and cleanest way to do it.

[@C4boxingsports]

What size n kind of roofing gun is the best

[@NWIVeteranConstruction]

i like bostich, hitachi is good too though. just my experience

[@taylorkirkpatrick906]

On the rake, you could foils the extra drip around the sub facia band. Keep in mind when the gutter comes in behind the drip edge, this keeps the water that comes down the edge of the rake from getting into the facia seams that come together at the corner

[@NWIVeteranConstruction]

Can't do that! This is a very common comment but the thing about the gutter is it goes out past the drip edge. All gutters extend about an inch past the edge of fascia. What you do is wrap the fascia, not the drip edge or gutter apron. That protects the wooden sub fascia. See my most recent video on fascia, it explains it all. Anybody who does that has a gutter that is too short, or the gutter guy cut that fascia and did it the right way

[@taylorkirkpatrick906]

Actually I've done gutters for 8years now, and also a certainteed certified master shingle applicator. Im telling you from experience you can wrap your drip, giving a nicer reveal, better water protection, and get the gutter an inch past the shingle line. We do it all the time, and I actually prefer the lazy method where people leave it hang heavy as opposed to the cut method so we can cut and wrap it ourselves afterwards if it's been missed

[@taylorkirkpatrick906]

I agree you wrap your fascia as well, but I'm telling you there is also a way to wrap the drip edge and you can put a wrap on top of a wrap and it's always a cleaner reveal

[@madukabandara6491]

Do you not install ice and water barrier in the whole roof?

[@NWIVeteranConstruction]

No. Only 2 ft past the inside of the exterior wall

[@AnthonySmith-yd9jb]

Are you licensed in Illinois? I need a total roof tear off and replacement. I live in Steger Illinois.

[@joshuasmith1215]

When you run that drip edge up the gable, why not bend one continuous piece over it rather than but up two pieces and have that opening on the top?

[@aaronmackay6123]

He is demonstrating in small scale. Quite often the pieces don't come in 30 foot lengths unless you have a fancy bending machine in the back of your truck

[@joeydelmarsjr.646]

what are all these material called? drip edge? flashing? roofing felt? starter?

[@davidlysohirka798]

Nice pouch!

[@wylandreed9797]

Why don't you run your I&W over your drip as a full run?

[@rickcopeland1153]

In Colorado we are required to use cap nails or cap staples in our underlayment it also voids the warranty on most synth felt

[@Wolferking]

My family house got hit by hurricane took some shingles off, wish you company is located where I live, because it looks like you know what you are doing

[@carlossantos-fh8jy]

Thanks for the video

[@NWIVeteranConstruction]

No problem!

[@cma3602]

If you put drip edge after ice and water isn’t the rain going to go under the drip edge if the shingles don’t protect it ?!!!

[@vhehn]

depends where you are. it goes under the drip edge in florida.

[@NWIVeteranConstruction]

plus you guys gatta tar right? i meant to mention it but video took too long.

[@Joshwagonda]

@@NWIVeteranConstruction Yes we gotta tar. Would definitely help you to throw out occasionally in your videos that what your doing is according to code compliance in your region.

[@user-xs5yi3pd1h]

Perfect👍

[@nmralsamr]

thank you for the video. when i can use the ice & water berrier? and when i will use flat roofing underlayment ? can i just use the ice & water to cover all my roofing ? thank you

[@NWIVeteranConstruction]

Ice and water is usually required along the eve edges to extend 2 ft past the inside of the exterior wall, and in valleys. I'd check your local code though with your building department. Depends on the area

[@nmralsamr]

@@NWIVeteranConstruction please please can i get your phone number if you don’t mind ❤️

[@petetheroofer3321]

Do you think you could do a slated roof? I'm in Scotland and only ever use slate or tile for pitched roofs and single ply or torch on for flat roofs

[@NWIVeteranConstruction]

With research and watching videos yes. I understand things very well but wouldn't jump into without knowing

[@petetheroofer3321]

@@NWIVeteranConstruction simple formula.... Length of slate - lap (usually 75mm depending on pitch) then divide by 2.... This gives you the "working gauge" then divide your roof height (eaves to ridge) by that number and that will give you the amount of courses on the roof, then divide your roof height (eaves to ridge) by the number of courses and that will give you your " true gauge" at which you will fit your slates to the roof, chalking lines at the specified gauge and laying the slates to they lines, massive satisfaction when you step back and have a look at the end

[@petetheroofer3321]

Obviously there is other things to consider but that is a basic rundown, maybe I should post a video? 🤣

[@6string327]

Slate or even concrete tiles which are widely used in Wales are unheard of in Canada and USA. It's tar shingles or metal tin roofs pretty much. Shingles typically give you 15 - 20 years life depending on the installer :)

[@stevengao8345]

i saw couple videos they put drip edge above ice and water shield and underneath shingle, and what you did is even under ice and water shield, very confusing for a noob like me , does the order really matter or not at all at this scenario? thanks

[@NWIVeteranConstruction]

I've done it every way. But from the thousands of comments on this channel the way I showed is the most accurate

[@stevengao8345]

@@NWIVeteranConstruction thanks for your reply, and good info to know

[@mm88swrt]

First! Woohoo!!!

[@Thenotfunnyperson]

A man knows his job.... A man doesn't wear useless toolbags to do a demo video of how to make a roof.

[@anthonydooley3616]

I like the old school tin snips.

[@paulschneider6202]

“I saw a guy staple his hand one time, good thing he’s fired” 😂

[@DanielinLaTuna]

Two reasons why you don’t want “nice and tight” on the drip edge: Firstly, the gutter guys that come behind you will hate that you didn’t leave them room between the fascia and the drip edge. Secondly, assuming a very straight edge, “nice and tight” isn’t as dreadful as I made it out above, but my eave-edge isn’t straight, and I’ll bet most others’ isn’t either. And if you try tight along the front, the top of the metal is going to buckle and wave. So leave about 1/2” gap and you’ll make everyone happy.

[@StevrenConstantine]

Who desiged this roof

[@fnhwk]

Drip edge never goes up tight to the fascia. If you can't figure out why, then I suggest you do!

[@PolvoronPapi]

My first day of roofing I woke up an hour early and here I am 😅

[@NWIVeteranConstruction]

Haha go to my "tear off/ dry in/ put back" video. It has a lot of views and You should get a bit out of that.

[@meblake7359]

that's not how you cut drip edge going over a gable end.

[@jaysonriffle9328]

Me watching this because my buddy hired me as a project manager for roofing...I have never installed a roof in my life!

[@joelpelletier8860]

Could explain why you put the drip tight against fascia or as tight as you can just so can explain to my boss my we need to stop overhanging it an inch or something. We only do it all because a eavestrouph guy gave him shit for going flush even though I was taught to install drip tight and have found his way makes hard to properly install starters

[@NWIVeteranConstruction]

Yea that's just crazy. Only thing I can think of is gutters are terrible going into drip edge. You have to use gutter apron on the eaves. It has a bend in it that allows the gutter to go up nicely unlike drip edge. And I think it's self explanatory wit drip goes tight to the sides

[@joeyt8256]

Also, maybe the eave guy was replacing the facia boards and wanted room to work on that specific job? Definitely goes flush with facia.

[@amesornish1232]

Thank you thank you

[@raulaguilar8757]

The metal needed overlap. Alltime

[@reptilekingdom9519]

“Good thing he’s fired” You can’t fix stupid. But…. Give a man a fish and you feed him for a day. Teach a man to fish and you feed him for a lifetime.