How to Adjust Motorcycle Engine Valve Clearance

One of the most important factors affecting valves temperature is that of valve lash or tappet clearance or valve clearance. Insufficient clearance will result in the valves contacting the seats for a shorter time and consequently operate at higher temperatures. Excessive clearance will result in noisy operation and loss of power. Great accuracy should therefore be used when adjusting valve clearance.
This video shows how to check and adjust the valve clearance in a motorcycle engine.
Especially for Honda Karisma 125D.
Tools:
1. Screwdriver
2. 8 & 9 mm box-end wrench
3. Pliers
4. Feeler Gauge
5. 17 mm socket wrench

[@chandtara4346]

Dear Sekolah you are very intelligent and described in a crystal clear way that is a great way of helping peopleThanks for the such informative description

[@sekolahonlineteknikotomotif]

+chand tara You're welcome. I'm glad if my video are helpful.

[@migzbenavidez]

Im actually impressed how he demonstrated and narrated what to do..keep it up :)

[@sekolahonlineteknikotomotif]

Thank you so much for your appreciation :D

[@bulletclub4life]

I understood this better than the other videos, you actually show close up what you are doing.

[@sekolahonlineteknikotomotif]

+HASE Thanks. I really happy if my videos can help people.

[@yokitpunzalan8159]

HASE s

[@alexnoga6879]

HASE

[@keithburns5707]

Honda has really good schools to train mechanics I went to one of them and it dealt mainly with tuneups there they described a valve adjustment by using the go-no go method. that means you’re putting your .003 mm gauge in but you use the .004 feeler gauge to verify that you have a perfect .003 mm. If the three goes in but the four doesn’t then it’s definitely the .003 mm. If you use this method it will make you a much better mechanic.

[@sekolahonlineteknikotomotif]

Thank you so much for your opinion, that's really informative!

[@keithburns5707]

Sekolah Online Teknik Otomotif You’re welcome I have one more tip that I noticed might help you when you’re trying to stick your feeler gauge in between the tappet and the valve take your feeler gauge and run it across the round part of a screwdriver to put a curl in it this will make it easier for you to stick the feeler gauge in good luck

[@sekolahonlineteknikotomotif]

Aha all right! Thank you again for your info! 😀👍

[@Tool19672]

Thanks for the video . From the looks of those caps you have had them off and on several times . Glad you got it figured out .

[@sekolahonlineteknikotomotif]

Haha, yah you're right. It's a little bit difficult to let them off, because its bolt was rounded.

[@jasonmaglinao9391]

Great tutorial. I appreciate that you offered a close up and detailed view of what you were doing.

[@sekolahonlineteknikotomotif]

Thank you so much for your appreciation!

[@masjosh]

This is one of the best tutorial videos I have ever seen. Great work and Thank you

[@sekolahonlineteknikotomotif]

+masjosh Thanks.

[@MrCRS55]

Very Clear demonstration, easy to understand. Thanks sharing.

[@sekolahonlineteknikotomotif]

+MrCRS55 Thanks for your appreciation👍

[@TheMediaclark2011]

Good Dude.. you end my expenses on going to a mechanic every month for expensive tune up! 2 thumbs up for you! god bless you!

[@sekolahonlineteknikotomotif]

Thank you very much for your appreciation. Well, reduced expenses. I'm happy to hear that!

[@user-xr9sq8ie6z]

I need namber the feeler

[@johnobvious1033]

Thanks man! Nice video. I'll bet it was annoying to get the camera angles set up right to get the valve adjustments, but I really appreciate your taking the time to do it.

[@sekolahonlineteknikotomotif]

Yes, that's absolutely true. It's a difficult angle, plus, my hand is dirty. Anyway. Thank you, thank you very much for your appreciation 👍

[@pcerr]

Very clear explanations! Crystal clear video. Keep up the good work. Thank you for posting this video✌️😀

[@sekolahonlineteknikotomotif]

Thank you very much for your appreciation 👍

[@ronaldodomacena9347]

i actually learned how to adjust my valve clearance on this video thanks a lot :-) you're a big help

[@sekolahonlineteknikotomotif]

+ronaldo domacena Thanks for your appreciation! I'm very happy to hear that.

[@theadventureofwave1002]

You the man! kudos young mechanic! :D thank you so much for this video

[@sekolahonlineteknikotomotif]

Thank you very much for your appreciation 👍 Good luck with your DIY

[@entingbhetoycolags9952]

Sir, do you know the measurement valve adjustment for honda cbr 150r 2011 model?

[@jangacharyguntoju9493]

You deserve appreciations. The way you explaining marvellous 👌👍👍

[@sekolahonlineteknikotomotif]

Thank you so much for your appreciation 🙌😀

[@familytrip2307]

Sukses terus ya mas, saya follow sejak 3 tahun lalu terimakasih ilmu nya walau saya bukan mekanik.

[@sekolahonlineteknikotomotif]

Terimakasih untuk apresiasinya. Semoga bermanfaat ilmunya mas 👍

[@Cavejohnson5353]

Thank you very much for making this video! Very well explained and easy to understand... Cheers!

[@sekolahonlineteknikotomotif]

+Hafiz Asim Thanks for your appreciation, Hafiz! 👍👍👍

[@raistub]

Great quality video. Details are good. Thank you. Really helped me.

[@sekolahonlineteknikotomotif]

+Rais Jufel R You're welcome.

[@kbk12356]

I am a korean Honda super cub repair is very helpful thanks^~^

[@sekolahonlineteknikotomotif]

I'm also happy to hear that. Thank you 👍

[@whimsymaker]

Clear and to the point...great job!

[@sekolahonlineteknikotomotif]

Thank you very much for appreciation 👍

[@aakersalonga2955]

ex. of valve clearance standard of suzuki shogun pro 125? any suggestions?

[@mateusangolar2881]

i am watching this video in 2020. i am going to apply the technique so solve the Noise of the valve in my SYM bike. thank you SEKOLAH.

[@sekolahonlineteknikotomotif]

Thank you for your appreciation! 😀 I hope you can solve the problem on your bike. Good luck!

[@cheapkickspinas3921]

Thumbs up for the instruction. But you forgot a important thing, first is to remove spark plug to release preasure of the engine for accurate valve clearance..

[@sekolahonlineteknikotomotif]

+Martin Apostol Thank you very much for your appreciation. If you can align the notch perfectly, I believe you can adjust your valve clearance accurately. Anyway, thanks for your suggestion!

[@gammaone9751]

Sir, you're motorbike is a replica of mine ( Rusi swish 100cc) can i do the same method you used in this video? or not?

[@sekolahonlineteknikotomotif]

+Bahala naa wala akong maisepp Oh replica? Is your Rusi engine components have similar type with Honda Karisma?

[@gammaone9751]

I can't say it's a fully replica but the company said that they make thier own engines, so i can't guarantee that ur method can work with my engine, also im new to motorbikes so i don't have too much knowledge to it

[@sekolahonlineteknikotomotif]

+Bahala naa wala akong maisepp Well, if so, I think you should see your particular motorcycle repair manual for proper maintenance procedures.

[@gammaone9751]

Sekolah Online Teknik Otomotif ok thanks 👍

[@mingming656]

Gamma One , dont you think that your bike is the replica? Judging from what you said" rusi" manufactures replicas of honda motorcycles, at least with the flairings only. Lol

[@pushparairai7407]

hello! bro, good job sharing knowledge to me.t.y.to u n my fren regarding the rocker arms adjuster, say for stand. how to get the 0.03 adjuster scale.

[@daviddefortier5970]

I apreciate that you try your best to speak english. Please keep up the effort

[@sekolahonlineteknikotomotif]

Thank you very much for your appreciation! 🙌

[@DustySquitoNM]

Feeler gauges have always felt a bit like black magic to me. They never really made sense because I never had someone show me in person. Still, your video really helped me a lot with my valve adjustment on my bike. Thanks, man!

[@sekolahonlineteknikotomotif]

+dustysquito Thanks for your appreciation. I really happy to hear that!

[@mryoso866]

Sekolah Online Teknik Otomotif hi sir can I chat with you about my problem in motorcycle?

[@sekolahonlineteknikotomotif]

Sure. Feel free to send your questions via KZbin comments. Thank you.

[@rowellmartires9423]

When i turn the flywheel to Top dead center.. is it okay to adjust valve clearance if the marking on the cam timing is not in position..

[@sekolahonlineteknikotomotif]

+xander blythe It's called "top dead center" if the notches were aligned. So, it's highly recommend to align the notches on TDC position before valve clearance adjustment. Thank you.

[@rowellmartires9423]

Thank you for your reply... Do you have videos on how to set cam timing?

[@sekolahonlineteknikotomotif]

+xander blythe Oh, I haven't yet. But if I have time and opportunity I will make this video request. Thank you.

[@rowellmartires9423]

Why is my T mark wont allign with the notch.. the flywheel slips when i allign it on the notch

[@sekolahonlineteknikotomotif]

+xander blythe Yes, it may happen. But try hold for a while in align position. I hope it helps.

[@erwinbanday2894]

Thanks for your video I learn more for the engine and I understand.

[@sekolahonlineteknikotomotif]

+Erwin Banday I really happy to hear that. Thanks!

[@kennethvillarosaarceo2629]

very helpful info tnx bro and check the valve spring if it is weak

[@sekolahonlineteknikotomotif]

Thank you for your appreciation. Yes, you should check your valve spring when overhauling cylinder head.

[@kingfreemovies6558]

thanks bro for the explanation now i know how to tuneup my motorcycle

[@sekolahonlineteknikotomotif]

+Emil Post Thanks! I'm glad you can be helped by this video.

[@kerzeratechgaming7024]

How tight is the locknut bro? Because when tightening the lock nut the valve clearance becomes tight even though im using a plier to secure the adjusting screw. It should not be super tight isnt it? Just a few turns will be fine?

[@sekolahonlineteknikotomotif]

+Moto Adventurer You need to see your repair manual for more precise torque, and it would be better if you use the torque wrench. However, if you don't have one, use your best knowledge/experience and feeling when tightening the locknut. Try to hold the adjusting screw as motionless as possible, you can use special plier or an SST L-shaped valve adjusting screw wrench. Good luck 👍

[@asadacidleo3425]

thanks bro for uploading a very good video for valve adjustment... camera working is very good...

[@sekolahonlineteknikotomotif]

+Asadacid Leo Thanks for your appreciation too!👍

[@nabilsyahmi3514]

Sir, do you know what is the appropriate valve adjustment for binelli keeway tx200 (BK tx200)?

[@sekolahonlineteknikotomotif]

Unfortunately, we have no repair manual for that particular motorcycle. Sorry.

[@anthonyr6555]

I can't insert my feeler gage 003. I don't won't to brack the manufacturer's seal ?. First time trying to fix. The cam spring is touching the adjuster nut is that ok. Dose the nut scrow in the cam spring? Thx

[@sekolahonlineteknikotomotif]

In our particular engine, (Honda Karisma 125) the adjuster bolt & nut stay on the rocker arm. Thus, the adjustment doesn't affect the cam spring. Only use the correct size for your particular engine (is it correct to use 0.03 mm for your engine?). If you can't insert the feeler gauge, try to make the gap wider by turning the bolt on counterclockwise direction. Then, adjust the valve clearances to the correct size (manufacturer's recommendations). Good luck!

[@anthonyr6555]

The bike is an ssr125cc yes it recommends feeler .003 ok I will try. The lock nut is the same as yours

[@pvsmouli7727]

nice work dude thanks for the video

[@sekolahonlineteknikotomotif]

+pvs Mouli Oh, thanks for your appreciation 👍

[@Flumphinator]

Very informative.

[@sekolahonlineteknikotomotif]

Thanks

[@wingbutler]

Great diction, man. Subscribed!

[@sekolahonlineteknikotomotif]

Thanks for your appreciation 👍

[@gabrieltianero6925]

I'll surely try this step by step process of yours. Its amazing and good job bro.

[@sekolahonlineteknikotomotif]

Thank you very much for your appreciation 👍 And good luck with your work!

[@anton161]

can you showcase a vega force i adjusting the valve clearance and other adjustments like spark plugs, etc.

[@sekolahonlineteknikotomotif]

+makoy161 Thanks for your request, but unfortunately we have no Yamaha Vega Force for makig that particular video. But I think, on similar mechanism types or components, you can follow our instructions for your particular motorcycle.

[@jhonbuagas7433]

thank you very much for clear explanation

[@sekolahonlineteknikotomotif]

+Jhon Buagas Ya, you're welcome.

[@rexlimbo5656]

Thanks to this video. Btw is this applicable to yamaha mio/amore scooter? And .03 is universal standard clearance of valve? Thank you

[@sekolahonlineteknikotomotif]

+rex limbo Basically, this procedure is applicable to manual adjusted valve mechanism. And yes, to Yamaha Mio. But the 0.03 mm size is not universal standard. Check your repair manual for that particular valve clearance size. Thank you.

[@dionirvingtimbang5212]

Any suggestion or troubleshoot a suzuki smash backfires and how to treat it. Hope you make a video. Thanks and more power

[@sekolahonlineteknikotomotif]

Severe backfire? My suggestion is you should clean the carburetor and then re-setting the idle mixture adjusting screw and the idle speed adjusting screw.

[@dionirvingtimbang5212]

+Sekolah Online Teknik Otomotif oksir thank you. i willtry it tonight.hope u post more videos.

[@sekolahonlineteknikotomotif]

Ok, good luck.

[@hodgiemodough]

Great video! Very helpful!

[@sekolahonlineteknikotomotif]

Thank you, thank you very much for your appreciation!

[@jhaes1360]

Can you help me sir. My wave 125 was refreshed but then we discover that the oil was not go through on the valve clearance my mechanic cant figure out whats the problem. We change the oil pump ang piston already.Thank you for any advice/help.

[@sekolahonlineteknikotomotif]

Thank you for your question. Firstly, you have to make sure the oil is sucked from the oil pan to the oil pump outlet. How was the result?

[@Zenx4rr]

Hello I just want to ask. Even though marks are not that much aligned tho I can move the valves with my bare hands can I start the adjustment? Because I cant align the mark keep moving its like it has a spring i cant align those mark I made a lot of turns

[@sekolahonlineteknikotomotif]

If you can't align the mark perfectly, try to remove the spark plug. Then try again to align the mark. Good luck!

[@boniboss1326]

thanks so much you which kind of issue we need to check the clearance

[@sekolahonlineteknikotomotif]

+boni boss You're welcome.

[@johnshanks7902]

Great video thank you

[@sekolahonlineteknikotomotif]

You're very welcome 👍

[@_wrhrdz]

Hello, i have a question. Does during top dead centre both valve (intake n exhaust) are closed? Should i just simply adjust the locknut with the mentioned measurement using filler gauge?

[@sekolahonlineteknikotomotif]

Yes, when the piston is at TDC (end of compression stroke), that is the best position/timing to adjust both valves.

[@jeffreyinlao9515]

nice one sir...i'll going to follow ur page for more tutorial...thx for d info man...

[@sekolahonlineteknikotomotif]

+Jeffrey Inlao Oh, ya. Thanks for your appreciation. 👍

[@jerryjeremy4038]

Sir may I request you to make a tutorial vid on how to detach and attached Fuel Injector of Yamaha Sniper 150 please?

[@sekolahonlineteknikotomotif]

+Jerry Jeremy I hope I could make that particular video, if I have a chance. Thanks for your video request.

[@munkeemunks]

great video! Im Planning to diy my own valve clearance of my '13 Honda Future 125 Which has the similar engine. Thing is, the stock O Ring of the Honda Future always have minor leaks. So i was wondering, is it possible if i just cut a piece of gasket paper with the same size of the tappet adjusting cover and use that instead of the o ring? Thanks!

[@sekolahonlineteknikotomotif]

+Munkee Munks Thanks for your appreciation! Well, the repair manual usually recommend you to change the old stock O-ring that causes leaks. However, it's possible to stop the leakage by adding sealant to the old stock O-ring or, as you said, using gasket paper. Personally, as recommended by the manufacturer, I prefer to change the old O-ring with the new-original one as it would be long lasting component. Good luck with your DIY!

[@munkeemunks]

Sekolah Online Teknik Otomotif so i guess if i change the o ring and adding the paper gasket on top of it, it'll be more effective?

[@sekolahonlineteknikotomotif]

+Munkee Munks The manuals recommend us to "just" change the O-ring, and as far as I know, it is faster and easier (or even cheaper!). Good luck!

[@munkeemunks]

Sekolah Online Teknik Otomotif ahahaha. i agree is faster and cheaper. But the leaks is just driving me nuts! ive changed it 3 times now... genuine Honda o rings. 😂😂

[@sekolahonlineteknikotomotif]

+Munkee Munks Well, I understand, in that case you can add sealant to help the o-ring. Good luck 👍

[@TorQue_WrenCh]

I also had honda 125,but in the manual says 0.10mm on intake valve and 0.17mm on exhaust valve..beside 0.03 is too small,engine can't be started at all

[@sekolahonlineteknikotomotif]

Thank you for your feedback. In this video we use proper repair manual for Honda Karisma 125, and yes we use the proper size for the clearances according to the manual. Maybe you have different engine type regardless the same engine capacity (125 cc).

[@onekeyngabolang7984]

mantab bro....lanjutkan tambahan info yg lain

[@sekolahonlineteknikotomotif]

+hengky turnado Ok kang, trims utk dukunganny.

[@marloubalag6528]

hi idol tnx for very informative and very helpful..ur not jus motorcycle mechanic ur mechanic also a 4wheels huh.nice may I know what's the right gauge for the valve clearance of my vegaforce 115cc engine specially intake and exhaust...?and I want to know if same procedure if I do it to my Vega the t mark of crank cover and the timing mark.do the same to Honda??

[@sekolahonlineteknikotomotif]

I have no reliable data or information resources for Yamaha Vega Force engine valve clearance, but as we know that Yamaha Vega Force have similar engine (and valve) to Yamaha Jupiter Z1, it seems we can use the same specification data with Yamaha Jupiter Z1 to Vega Force. Jupiter Z1 have 26 mm intake and 21 mm exhaust valve diameter, and Vega Force was the same. So, this is Yamaha Jupiter Z1 engine valve clearance (when cold): Intake valve: 0.08 mm - 0.12 mm Exhaust valve: 0.08 mm - 0.12 mm the procedure is a little bit different, you need to open cylinder head cover to adjust valve clearance, and the mark on the generator rotor maybe only the "I" line-shaped. I hope this helps.

[@buhaydriverjotv9593]

ya ok, can you have valve. a clearance of intake ,& exhause of SYM 110 2015 Model?

[@sekolahonlineteknikotomotif]

Thank you for your question. Unfortunately, I don't have the repair manual for that particular model. I'm sorry.

[@philipvillar9428]

my question is gauge the same the upper n lower ,for there so many say not the same,n some say is the same what is true

[@sekolahonlineteknikotomotif]

+Philip Villar Different engine may have different valve clearances. So it's highly recommended to see the sizes on repair manual. Thank you.

[@Mattd252]

Good video - you explained it well. Very helpful.

[@sekolahonlineteknikotomotif]

Thank you for your appreciation :)

[@goddest84]

Do you have idea on valve clearance of KLX150L bro?

[@xtiancarpio]

do we need to remove the spark plug for the wave 100 before getting the TDC

[@sekolahonlineteknikotomotif]

Yes, you may need to remove the spark plug if you find it difficult to align the notches.

[@summer5846]

is there any changes if I replaced my stock camshaft to a higher lift camshaft.

[@sekolahonlineteknikotomotif]

+jeepney joyride Yes, you can replace your stock camshaft, but as far as I know, it would need different valve clearance (size). Good luck 👍

[@seguiakura5584]

Thank you Folks great help👍👍👍

[@sekolahonlineteknikotomotif]

+Segui Akura Thanks for your appreciation too 👍

[@joemarievista1354]

Sir,why my kawasaki fury the gear is continues changing 4rth gear into neutral. Tnx

[@sekolahonlineteknikotomotif]

I can't predict the malfunction. You need to disassemble the transmission, and then check the faulty components. Good luck.

[@diosdadojr.manghino8518]

It is the same method of tuning in xrm110? Is the valve clearance the same?

[@sekolahonlineteknikotomotif]

+Diosdado Jr. Manghino Actually, I don't have much experience on XRM110. But, basically, the method for adjusting the valve clearance is nearly similar. Unfortunately, I don't have a repair manual for XRM110, but most people said that the valve clearances for XRM110 are 0.04mm (IN) and 0.06mm (EX). I'm glad to hear how is the result. Good luck for your project!

[@ericredraj3558]

thanks a lot. greetings from Philippines

[@sekolahonlineteknikotomotif]

+Eric redraj Oh ya, very nice Philippines 👍

[@geogeo8880]

thank you for sharing sir more power

[@sekolahonlineteknikotomotif]

+Geo Lugtu Thanks for your appreciation too👍

[@dondonlopez1013]

sir may i know the exact clearance of xrm 125 honda in intake and exhaust . thank you

[@crisellbernardo5023]

gud morning sir, i try for the fist time adjusting valve.im using .003 mm feeler gauge.its desame with 0.03mm? coz i dont see 0.03 in my feeler gauge.when after i adjust valve according to my feeler gauge .003 mm i heard noise and hard starting also when its start its suddenly lost power also that noise.thanks

[@sekolahonlineteknikotomotif]

Before you start the process, you should know exactly what is your engine valve clearances (for example, 0.03 mm is only for Honda Supra or Karisma 125). Be careful with the size, 0.003 mm is absolutely different from 0.03 mm. So, use only the proper feeler gauge blades. Good luck!

[@natangburek8979]

Siau aku ingat siam pilipin viekong tadi Lool All the best

[@joeybernabe7963]

Great explinition man..

[@sekolahonlineteknikotomotif]

+Joey Bernabe Hey, thanks for your appreciation 👍

[@joeybernabe7963]

Sekolah Online Teknik Otomotif welcome sir

[@JK-fr3qp]

Whats the clearance for raider j pro 110?

[@ichromelast7701]

what is the valve clearance of honda xrm 125?

[@SuperPertinax]

Thank you very much

[@sekolahonlineteknikotomotif]

+SuperPertinax Ok, you're welcome.

[@devenderkachhawaha1787]

SuperPertinax

[@herminigildodelacruzjr1752]

ok thank you again nice video

[@272706bry]

thanks man it helps me a lot..best tutorial video..

[@sekolahonlineteknikotomotif]

Thanks.

[@cheeyuktong4205]

sir, my gauge does not have 0.03, my lowest gauge is 0.5,. if I am able to adjust the valve of my honda dash, what is the right gauge for it, and what am I going to use in mm. thanks.

[@sekolahonlineteknikotomotif]

+shok tong I think you're using car feeler gauge which is more thick, try to use motorcycle feeler gauge. Unfortunately, we have no info about Honda Dash valve clearance, because there's no Honda Dash in Indonesia. Maybe you can search on Google for that specification. Thanks.

[@greenbee8134]

Very informative informatio.. Do you have an idea of the valve clearance of rouser 135?

[@davemaximo9952]

antatanga nia.common sense lang.any adjustment from 0.03 to 0.06.kung san kau komportable

[@xtiancarpio]

Hi Sekola Xtian from the Philippines here. May I know whats is the clearance for a Honda Wave 100r 2007 model?

[@sekolahonlineteknikotomotif]

Intake 0.05mm (0.002 in), Exhaust 0.05mm (0.002 in). Good luck!

[@rabacs1324]

Sir may i know what is the stardard gauge clearance intake and exhaust for xrm 125? Thank u for your rply..

[@nicanorbadal689]

Ramil according to my xrm 125 valve clearance should be: Int: 0.05 mm (0.002 in) Exh: 0.05 mm (0.002 in)..i notice that the intake and exhaust valve have the same clearances.

[@nicanorbadal689]

I should have said xrm 125 owners manual.

[@kalmadolng8405]

very nice tnx man nw i knw how to adjust my bike

[@sekolahonlineteknikotomotif]

+Puppy214 Wowo Ok, thanks.

[@sekolahonlineteknikotomotif]

+Puppy214 Wowo Ok, thanks.

[@sadatelian6765]

Tnx for this video

[@sekolahonlineteknikotomotif]

+Sadat Elian You're welcome.👍

[@mxnxxlcxbxg3543]

What whill happen if the clearance is not right? What if you dont know the right clearance?

[@sekolahonlineteknikotomotif]

If you set the improper valve clearance, the valve mechanism will skittle away the rattle sounds (if the clearances were too wide), or the engine power will be reduced because of compression and combustion loss (if the clearances were too narrow).

[@celsotanjay4685]

NICE ONE SIR!

[@sekolahonlineteknikotomotif]

+Celso Tanjay Thanks! 👍

[@evemizerrago7287]

Sir you know the exact valve clearance of kawasaki aura nexus 125? from intake to exhaust..

[@sekolahonlineteknikotomotif]

Unfortunately no, we have no resources for that particular bike. I suggest you to search through the internet.

[@CipconFamily]

Try to check inside the trunk of your bike usually there is a sticker.

[@lennycruz4558]

Intake is 0.3..how about the exhaust clearnce? Do you have video on honda xrm 125?

[@sekolahonlineteknikotomotif]

Unfortunately we don't have the video of Honda XRM. But you can use the main procedure on this video for your particular motorcycle. You only need to search the proper specification of your engine valve clearances. Good luck!

[@lennycruz4558]

Sekolah Online Teknik Otomotif ok thanks sir

[@sekolahonlineteknikotomotif]

You're very welcome 👍

[@kosalmorn72]

I like all your videos So much ce

[@sekolahonlineteknikotomotif]

+Kosal Morn Oh thanks :)

[@jaysonsardon9626]

very nice and good idea.

[@sekolahonlineteknikotomotif]

+jayson sardon Thanks.

[@lancerizon966]

thanks for the clear video sir... i think i know to adjust my wave 125 valve clearance now... i think we have the same feeler gauge size .03mm for my honda wave..i hope you can provide more video specially how to tune up engine adjusting air in carburetor thank you so much

[@sekolahonlineteknikotomotif]

+lance rizon Ya, you're welcome.

[@eleuteriorizon988]

hi sir thanks for your video I actually succeed adjusting my valve clearance.but my problem again my throttle if I give gasoline the engine will stop please help me

[@sekolahonlineteknikotomotif]

+ELEUTERIO RIZON Oh ya, I'm happy to hear that. But could you please explain what does "if I give gasoline" mean? Did you mean idle up?

[@joelpajarillo3707]

try to clean the airbox and the carbuator if the problem is still there check the gas pump maybe your gas pump is not good anymore

[@sekolahonlineteknikotomotif]

+Joel Pajarillo 👍

[@dondonlopez1013]

Sir may I know the exact. Measurement of xrm 125 honda. .use in feeler gauge tnx and more power..

[@sekolahonlineteknikotomotif]

Unfortunately I have no repair manual for this particular bike. You may ask in the riders forum.

[@stanlyneo292]

saya ingin bertanya?disebabkan kes lupe tukar minyak pelincir ,sya guna ekzos chamber.motor mengalami masalah bunyi ketuk di dalam bila motor berjalan bila dilepaskn tiada.bunyi kuat .adkah krna teppet longgar or what?n jgak minyak hitam saya cepat habis bru seminggu pakai .lalu bila direm moto keluar asap melalui ekzos .apkah masalah nyer????help me?

[@sekolahonlineteknikotomotif]

+stanly neo Sya sebetulnya tidak terlalu paham keseluruhan pertanyaannya, mungkin ini karena anda menggunakan bahasa melayu, ya? Bunyi yang kuat ini kira-kira bersumber dari mana? Kepala silinder, blok silinder, atau crank case?

[@stanlyneo292]

kepala sllnder

[@sekolahonlineteknikotomotif]

+stanly neo sudah coba setel celah katupnya (valve clearance)?

[@MrAloysioguimaraes]

Hey, Jadav. Could you solve me a doubt? Thanks in advance for any help. In fact, I haven’t found anything clear on the Internet. So I came across with your video. The situation is, suppose I have to “Adjust Motorcycle Engine Valve Clearance”, what is the consequence if I let the admission or exhaust a opener or closer than the standard setting: in terms of performance, top speed and fuel saving? Thanks a lot for any clue. I am thinking about a one or two-cylinder motorcycle.

[@sekolahonlineteknikotomotif]

Insufficient clearance will result in the valves contacting the seats for a shorter time and consequently operate at higher temperatures. Excessive clearance will result in noisy operation and loss of power. This means, loss of power = bad fuel saving. So, great accuracy (standard timing) should therefore be used when adjusting valve clearance.

[@MrAloysioguimaraes]

Man, I felt very pleased about your generosity in answering my questions. Thanks you very much. Nice day!

[@sekolahonlineteknikotomotif]

+Ags Guimaraes No problem. You're welcome 👍

[@siGnn7]

Hi, I adjusted my valve clearance. its a Honda Click. However, now my engine stalls/dies during idle or while running.

[@sekolahonlineteknikotomotif]

Recheck your adjustment. Is there something wrong? Always check and adjust the valve clearance on the TDC compression.

[@siGnn7]

@@sekolahonlineteknikotomotif thanks. i examined my engine. a few seconds after starting, i see some sparks that escape from the sparkplug cap. this is not normal right? I think i will need to replace the cap. Need to look for tutorial how since shops are far feom my area. thanks for the reply!

[@sekolahonlineteknikotomotif]

Yes, that's might be the main problem. The electric current shouldn't jump through the cap. Good luck with your work!

[@rpyordan]

nice video sir, any way sir, can I apply that to my Kawasaki wind 125 engine sir?? thanks!

[@sekolahonlineteknikotomotif]

+Rogem Yordan Basically, yes, I think this procedure principle can be applied to your Kawasaki.👍

[@naysoehtun6129]

I appreciate it Sir. It will be quite useful Sir.

[@sekolahonlineteknikotomotif]

Thank you very much for your appreciation 😀

[@redweedes8880]

can also adjust the cam shaft chain if there is adjustment available?

[@sekolahonlineteknikotomotif]

I don't really understand what this question mean. Please clarify again. Thankyou.

[@jaimepicornell5773]

Very Good Work

[@sekolahonlineteknikotomotif]

+Gen Jimmy Hei, thanks for your appreciation 👍

[@dontdropitlikeustoleit2012]

help me alot do u have a video of how to change a valve seal?

[@sekolahonlineteknikotomotif]

Unfortunately the video about how to replace the engine valve seal are not yet made, but if one day there is an opportunity and time, I will make this video request. Thanks.

[@mckav2358]

Very helpful thankyou

[@ejtalavera44]

Sir how about yamaha crypton z what is the standard valve clearance?

[@sekolahonlineteknikotomotif]

Thank you for your question. Unfortunately I don't have the data for Yamaha Crypton at the moment. I'm sorry.

[@glennlayaguin]

Thanks for sharing idol nice one video very informative idol

[@sekolahonlineteknikotomotif]

Thank you for your appreciation :)

[@jasonang2756]

rikues dong mas, perawatan & setting mesin standar FU carb. terutama bagian2 yg ada penggantian part berkala, misal clutch plate, brake master cyl, dll sukses terus :)

[@sekolahonlineteknikotomotif]

+Jason Ang Trmks utk requestnya. 👍 Mdh2n klw ad kesempatan ya kang.