Check out our other video on how to adjust stand mixer! great alternative! kzbin.info/www/bejne/raK3h5xvrpmYhaM Always remember to press down on the screwdriver as you turn. The use of pliers to help turn screw can help. W40 overnight or heating the screw can help
@junipervip6813 жыл бұрын
I cannot thank you enough for this! Why they don't put this critical info in the users manual is an issue itself. My Cuisinart went from being useless to a key tool in my kitchen. It took a full 1-1/4 turns to get it calibrated properly. It was a tight twist, but rather than a second tool, I used both hands and firmly twisted with the wrist. Thank you again and please keep these informative videos coming!
@lilidlamouche7 ай бұрын
Same here!!!!! ❤❤
@sckl20112 жыл бұрын
Must have to be Superman to move that screw, I didn't want to strip the screw but the screw was so tight i broke my drill bits in the process. I then went on reading comments and noticed one of you were suggesting removing the bottom plate so I did. I added some washers leveled the plate and it worked perfectly! So simple and no damage.
@cameronphenix20962 жыл бұрын
For Cuisinart users who have thr attachment too high/bowl too low: I tried for days to get that screw to turn but I ended up just stripping it. Eventually I realized there is a metal plate the bowl screws into on the bottom. Taking that off and placing small strips of paper stack up inside and screwing the plate back on solved my problems instantly and was much easier and faster.
@mitchelllevine20232 жыл бұрын
Does KitcheneAid have have the same problem?
@cameronphenix20962 жыл бұрын
@@mitchelllevine2023 I'm sorry, bud. I wouldn't know
@qwertyuf2 жыл бұрын
Thank you so much👍👍👍👍 You're a genius!
@BoomerBomb26 Жыл бұрын
@mitchelllevine2023 yeah it does but the screw is easier to turn way easier
@armorfid2 жыл бұрын
I tried everything to turn the screw clockwise, but it wouldn't budge. Then, I turned it counterclockwise and it was surprisingly easy. So, the screw was already turned all the way in, but there was still a gap! I unscrewed the bowl plate, placed 3 nickels with double-sided tape in there, screwed back the plate, and that did the trick.
@SugaBee983 жыл бұрын
My goodness thank you 🙏. I just purchased my new Cuisinart Mixer and used it for the first time. After unsuccessful results I went to o the Cuisinart reviews and discovered this video on how to adjust it. My husband watched your video and now my mixer has been adjusted perfectly. Thanks so much 😃
@sashineb.21145 жыл бұрын
Good to know, thanks. On Amazon people were saying there is no way to adjust the height. But I'm glad I've found your video.
@XeninWorx5 жыл бұрын
Just got my Cuisinart stand mixer and did this adjustment right away. Really easy if you’re using a ratchet with an extension. Very little effort to turn. Only needed to turn 3/4 of the way and it’s perfect. Thanks!
@wanderingaloudwithmark30573 жыл бұрын
I've read that the adjustment screw has been seated with lock tight making it difficult to turn. This was not the case with the ratchet? Other people have stripped the flat head screw.
@XeninWorx3 жыл бұрын
@@wanderingaloudwithmark3057 was not hard at all to turn.
@LynnTran3 жыл бұрын
Mine really hard to turn😭
@mitchelllevine20232 жыл бұрын
@@wanderingaloudwithmark3057 - I am not able to turn the screw clockwise to lower the wisk. How do you use a ratchet to turn a screw? I am losing patients with this "fix". I'd love to hear from other uses that have been successful.
@Riggobernational2 жыл бұрын
@@mitchelllevine2023 a 1/4 ratchet with a 1/4 flat head bit, if 1/4 isn't long enough try 3/8. This can be bought at any hardware store, the idea it to use one hand to keep pressure on top of the screw and turn it which way you desire with the other (on/off).
@lisadyerlamoreaux1311 Жыл бұрын
We couldn't get the screw to budge either. Thanks for the idea to remove the plate below the bowl. Easily removed that plate, added washers & working great! Thank you!
@fredvarao38942 жыл бұрын
I thinking about buy the Kitchenaid, but the Cuisinart is half the price, and seams to do the same. I just looking the videos about this two brands and I think the price difference is more about the looking then the cooking. I will buy the Cuisinart. Thanks for the video!
@CShannon19913 жыл бұрын
Thank You for making this video. This past November, I bought myself my very first KitchenAid Tilt Head Stand Mixer which happens to be a Deluxe 4.5 quart model. I tried to make meringues one time but the whisk wasn’t reaching the bottom of the bowl and so I did this method and it solved the problem. Again, Thank You for making this troubleshooting video for KitchenAid and Cuisinart stand mixers!
@mitchelllevine20232 жыл бұрын
Is it so that the problem exists with both Kitch Aid and Quisinart stand mixer?
@lucyc4 жыл бұрын
I was super excited to find this video - thank you!!! I tried doing this today, but I can't get the screw to turn, in either direction. The screwdriver I used fit fine in the space, so that wasn't the issue. I tried some 3-in-1 oil to see if it just needed to be lubricated and that didn't work, either. Any tips you (or anyone else) could offer would be greatly appreciated!!! Thank you!!!!!
@TaylorOusley-o3o10 ай бұрын
Thank you for the video it was very helpful. I wanted to ask how to stop my cuisinart wobbly head?
@doogenevil2 жыл бұрын
Yeah, I couldn't get that screw to budge but quarters under the plate the bowl locks into worked like a champ
@judytheburkinshaw29352 жыл бұрын
Thank you for this video! I was frustrated with my new Cuisinart because it couldn't even wisk eggs properly. I followed your advice and it works very well now.
@StatUpBox2 жыл бұрын
Wonderful!👍😊❤
@sumonesmum Жыл бұрын
Well, after a bit of frustration I got it adjusted. The first step was to heat the screw with a blow dryer, then I used vise grips on my stubby screw driver and it moved! As it moved some sticky red stuff came out. I assume this is meant to hold the screw firmly (locktite?).
@StatUpBox Жыл бұрын
awesome! great tip! 💪😊👍❤
@sylviah19693 жыл бұрын
Thank you so much !! I was becoming frustrated by this problem . Now I'm a happy camper ! :)
@BobCCLIV5 жыл бұрын
Thanks so much for doing this you are a lifesaver!
@lin11669 ай бұрын
Thank you for this video. I just purchased a Cuisinart Stand Mixer, so I haven't used it yet. It's good information though, if I ever need to make an adjustment.
@StatUpBox9 ай бұрын
Glad it was helpful!
@ummahmedca2 жыл бұрын
With the amount of money we pay for these mixers we shouldn't have to struggle to make these adjustments. The manufacturers should make adjusting the bowl an easy fix.
@bettyloohoo773 жыл бұрын
I am so glad you made this video, thank you!!!!
@JasperXCXeon Жыл бұрын
Thank you so much for this, fixed my dough hook problem instantly!
@StatUpBox Жыл бұрын
awesome 👍😊
@squee2224 жыл бұрын
good video. Worked perfectly. New mixer was a little high. I used a little water instead of a dime to judge the depth.
@StatUpBox4 жыл бұрын
Nice. Great tip
@elainemartin699311 ай бұрын
Great video. Love to see how to lubricate this machine - oven clean the motor area
@ReneeMu5 жыл бұрын
Exactly what I was looking for! Thanks so much.
@marynzom51023 жыл бұрын
Thank you for the video, I hope this will solve my mixer problem because it doesn't cream at all
@Kt-cn2rq2 жыл бұрын
Same I was so frustrated creaming butter and sugar for simple cookies hope this works.
@James-kd2cm2 жыл бұрын
Thanks for the video… I adjusted down until the screw was getting too tight. I’ll probably need to adjust the base as others have mentioned in the comments.
@JoshuaWilsonpossible3 жыл бұрын
OMG this is fantastic! Found this video sifting through Amazon reviews. Now I'm subbing your channel! so many goodies!
@TheLugnut3 жыл бұрын
Great video! You saved Christmas baking 😁
@gregbarker5804 жыл бұрын
I like this video I have a progress stand mixer but the beaters don’t reach the bottom of the bowl can I use this video for lowering my stand mixer?
@marionmoskalyk37563 жыл бұрын
This was very helpful. Thank you.
@alicegriffiths45438 ай бұрын
Thank you so much! The company hotline said “this is not an issue” - ie put eggs in the bowl and the whisk doesn’t even touch them. All fixed now!
@StatUpBox8 ай бұрын
Awesome 😊👍
@patkaelin81415 жыл бұрын
I’ve tried to turn the screw clockwise, but it won’t budge. Any suggestions? I don’t want to tear up the screw head trying to turn it, but I would really like to lower my blades. Would WD 40 help?
@StatUpBox5 жыл бұрын
Using some pliers and screw driver is what did the trick for us, or if you are able to get ratchet with a screw tip. You have to pressure down the screw ( so you wont strip the screw) and turn with force . It appears that it has some thread locker ( if you see on the video the red thing that comes out from around the screw) . Once loose , its easy to turn at any moment, but yes the first turn is the hardest. It wont hurt to use w40 and maybe letting it set in for for a couple of minutes as well. good luck.
@gregbarker5803 жыл бұрын
Nice video can this method be bone on a Progress EK3593P?
@sonadasturmalladi93582 жыл бұрын
Excellent instructions
@StatUpBox2 жыл бұрын
Glad you think so!❤👍😊
@michaeldavidson8971 Жыл бұрын
Do you adjust the paddle using a dime as well? but if you do this the whisk will touch the bowl because it’s longer and why is it bad for the whisk to touch the bowl? when you whisk something by hand you touch the bowl, what’s the big deal?
@daveg872 Жыл бұрын
Thanks for sharing this important information! Cuisinart is shortsighted for not including this in the instructions.
@StatUpBox Жыл бұрын
Our pleasure!
@elecsheep94 жыл бұрын
Tried this today and I could not get the screw to budge, even with a ratchet screwdriver. I'm worrying about the slot starting to get stripped. So, instead I tried approaching it another way. Rather than lower the head, I decided to lift the bowl. I removed the metal plate that holds the bowl, put three quarters below it (one in between each screw), and then put the plate back on. It helped. By my calculation, if I tape together a quarter and a nickel it should raise the height so that whisk attachment will scrape a dime in the bowl. The pressure from the plate seems to hold the coins in place.
@StatUpBox4 жыл бұрын
Awesome Tip!! 🧠 Beats 💪 Thanks for sharing. 😁
@elecsheep94 жыл бұрын
@@StatUpBox So taping together a nickel and a quarter got it from my factory setting down to a dime level with the whisk attachment. However, it is still a good 3/4 inch from the bottom with the dough hook. Of course, raising the platter will give you more leeway to lower the tilt head, if you can can get the screw to budge!
@StatUpBox4 жыл бұрын
Nice! Have you tried something like W40 overnight?
@danielmertowski44233 жыл бұрын
@@StatUpBox TRY HEATING THE SCREW, THATS WHAT YOU DO TO RELEASE LOCKTITE
@sckl20112 жыл бұрын
Worked like a charm. Thank you for posting that. I added some metal washers till the plate was perfectly level. Don't use paper though cause it will degrade.
@jetrey95538 ай бұрын
I think there is a difference with the colors and it’s ease of adjustment. I have both the white and the silver one and the white one was super easy to adjust but the silver one no matter how much I tried it wouldn’t turn
@michaeldavidson8971 Жыл бұрын
Thank you so much!
@StatUpBox Жыл бұрын
your welcome!
@esthermontes50897 ай бұрын
Gracias por la información!!!!
@StatUpBox7 ай бұрын
de nada. 😊👍
@marshannajohnson85843 жыл бұрын
THANK YOU SO MUCH!😘😘😘
@adelecampbell-white264810 ай бұрын
wondering if anyone knows where to get a scraper paddle attachment for the cuisinart mixer??
@gamecock24654 жыл бұрын
That’s a great tip.
@cwinegarden64264 жыл бұрын
Thank you very much! Well done.
@rosccz95673 жыл бұрын
Useful video!
@ChaCha6612 жыл бұрын
Thank you !
@StatUpBox2 жыл бұрын
You're welcome!
@BluesNomad3 жыл бұрын
Tried to turn it tonight, used a little WD and it turned a tad I think but going to try to keep it under oil overnight and see what happens...
@StatUpBox3 жыл бұрын
great idea! yes, the hardest part is to break it the first time. after that initial break and from there on will be piece of cake.👍💪 good luck!
@laoluu2 жыл бұрын
@@StatUpBox I think there is locktite on the screw.
@ompaloompa4970 Жыл бұрын
Thank you 💗☺️!
@StatUpBox Жыл бұрын
You’re welcome 😊
@kennethwilson27129 ай бұрын
Couldn’t get screw to turn in either direction so I removed the bottom plate I raised it until the screws no longer would reach
@kandy4u49t10 ай бұрын
Thank u
@StatUpBox10 ай бұрын
your welcome 😊👍
@seamusellis145023 күн бұрын
All the reviews of the Cuisineart I've seen mention the ingredients in the bottom of the bowl getting missed ...and yet there is NO mention of adjustment being possible in the manual ...
@sugeyescorche33093 жыл бұрын
cual de las dos es la mejor??? por qué la misma empresa saca dos batidoras...? Por qué no viene de unas vez graduada para no tener ese inconveniente con la cuisinart...hay que bajarla para que pueda llegar a la base del bool...
@johnrees62903 жыл бұрын
What kind of jerk puts red lock-tite on an adjusting screw? Not KitchenAid.
@robertknight46723 жыл бұрын
There's a guy that sells something called an everdime for tilted kitchen AIDS to keep it from coming out of adjustment. www.mrmixer.store/store/p/everdime
@blschafer4310 Жыл бұрын
I know. I turned my Kitchenaid no problem, and I have weak hands.
@BradWarren3 жыл бұрын
Thank you so much - my Cuisinart stand mixer's height was making me a bit mental. How could they engineer something to be mass produced that seemed so flawed and I'm a baking noob too.
@laurad11713 жыл бұрын
I agree! I was so excited to get a Cuisinart stand mixer only to be disappointed that it wasn't getting all the way down! Glad I found this video!
@Rock4UNow2 жыл бұрын
Thank you
@StatUpBox2 жыл бұрын
You're welcome
@macymodestxchange63556 ай бұрын
Mine won’t budge. Even with the channel locks trick. Won’t budge.
@loveloveiloveuforever72472 жыл бұрын
voltage?
@michellelee14244 жыл бұрын
My mixer head won't lock/stay up when I lift it,how can I fix it?
@cherylschrader69734 жыл бұрын
I can not get the screw to budge on mine. It is super tight! Suggestions?
@StatUpBox4 жыл бұрын
try w40 overnight. good luck
@beachlifesoy22533 жыл бұрын
no matter what i do the screw won't move and i'm just stripping it!!! do I just return the machine? because its useless at this point
@wanderingaloudwithmark30573 жыл бұрын
I've read reviews on Costco stating the same.
@victorianojordan79824 жыл бұрын
Hi StatUpBox! thanks for the video, it was very useful! ... I would like to ask you how we can solve the fact that when using the dough hook, the dough starts to rise on the hook up? It happens to me with some doughs and I must stop and remove the dough from the hook to continue kneading ... Thank you
@StatUpBox4 жыл бұрын
We noticed that it only happens to us when we use about 7 to 8 cups of bread flour, plus taking in account the other ingredients. The manufacturer user manual state's 6 cups is the maximum. Other than that we dont get the issue. Hopefully this helps out. Good luck.
@i_Am_TH Жыл бұрын
Am I the only one that has this problem? The whisk is touching and scratching the bowl. Plate at the bottom sits perfectly, doesn't seem like I can get it any lower. And the screw didn't even one bit. And like so many others, I don't want to strip the screw. So what do I do if I can't adjust the plate at the bottom??? 🤦🏻♀️
@Shernickyholmes221 Жыл бұрын
I tried this today, in my cuisinart. Now, there is a rattling in the head. Just return the piece of junk.
@LynnTran3 жыл бұрын
The screw so hard i cant turn
@amyvandenberg1309 ай бұрын
Did nothing for the cuisinart. Screw turned but it didnt matter.
@judneg065 жыл бұрын
I tried to adjust mine but the screw is so tight it is impossible to do
@StatUpBox5 жыл бұрын
At first it will be tight. You will need to put some power on it. Using some pliers to hold screwdriver or a wrench style screw driver, meanwhile you press down, can help. After initial turn, it becomes easier. Also adding some wd40 can help.The screw is meant for adjustment. Good luck.🏋️💪
@danielmertowski44233 жыл бұрын
@@StatUpBox IF YOU HAVE A SOLDERING IRON, YOU CAN HOLD IT ON THE SCREW TO WARM IT UP AND RELEASE THE LOCKTITE THAT IS LOCKING IT IN PLACE, SO IT DOESN'T MOVE FROM VIBRATION.
@emt40842 жыл бұрын
Why is it bad for your health if it touches?
@blschafer4310 Жыл бұрын
Scraping off metal shavings.
@dalecameron87913 жыл бұрын
My husband , who is a big strong guy, cannot get the screw loose period, so he has just put the dime underneath the bowl...
@robertlogue37943 жыл бұрын
Don't think we can raise the bowl on my Cuisinart because the bowl locks in place. That was a good idea to put the coin underneath it😅 I hope the screw isn't too hard to turn when I try.
@likeadrinktrae2 жыл бұрын
Mine cuisineart is extremely stuck and I can’t move the screw at all. So much for having a stand mixer. :(
@gauseb2 жыл бұрын
Hands down the worst product I've ever used. Why put a tiny screw in a place that is not accessible by nearly anyone. Tutorial was great but couldn't get it. I'm returning this mixer
@brockbutts72693 жыл бұрын
This screw will not turn right!
@stephaniesochan5273 Жыл бұрын
I can’t get my screw to budge no matter what 😭
@StatUpBox Жыл бұрын
We also have alternative way video kzbin.info/www/bejne/raK3h5xvrpmYhaM
@stephaniesochan5273 Жыл бұрын
@@StatUpBox thanks. I tried the alternative too and one of the 3 screws was seized and I’ve damaged the screw head trying to get it out haha. I was so desperate for one to work as my paddle is so far out of alignment that the machine is useless.
@queenystars3 жыл бұрын
perfect but my machine not have that screw what to do
@robertknight46723 жыл бұрын
Is it Kenwood? I believe they also make some mixers under other brand names but they usually have adjustment nuts on the beaters themselves. You might want to check those out.