How to adjust valve clearance - Honda 1.8, 2.0 - CR-V, Civic, Accord. Valve lash - DIY R20A9

[@lukespack]

I used to do my old Toyota pick-up about 35 years ago and it took under an hour. It is fairly simple. You did well.

[@PlumbCarton5607]

I've done this a few days ago to my civic that has 225,000 miles on it, 2 of the exhaust valves were over 0.05mm too loose🤯. Unfortunately after i was done i noticed the car was super low on oil, I don't know where it went? Maybe it was because it took hours over 3 days to do it? There's no leaks... I'll fill it back up again then start it.

[@sublovelows]

So, after you finished adjusting the last valves #2. Do you need to reposition back to the number 1 (TDC) before before starting the car? Thanks Very detailed video.

[@fixanddrive]

No. You just fit the cover, wait for the silicone seal to dry and start the enigine.

[@sublovelows]

@@fixanddrive thanks

[@Hardenth50]

do you know the spec for a valve clearance of honda hrv 2020? by chance could find any manual repairs on hynes of 2020

[@zachmarshall7921]

Is this the same procedure to do the 1.5l turbo 2018 released in North America?

[@fixanddrive]

I don't know.

[@civicr16a22]

Hi, Do you have any info what are the valve clearance values for Honda Civic R16A2 engine? This engine is for the 8th generation 1.6 Civic Sedan.

[@TheMstwntdLMSV123]

How is the engine after adjustment? Do you notice a difference in sound or performance?

[@fixanddrive]

I don't notice any difference in performance or sound. It was and still is quite a silent engine

[@TheMstwntdLMSV123]

@@fixanddrive This video is actually in perfect timing. My friend just bought a Honda Civic with the R18Z1 (Very similar to this engine) and it requires a valve adjustment service. I will be able to help him complete the service and reference this video!

[@jacekfajkis1237]

Jak znaleść wartości do luzów zaworów ?w książce serwisowej będzie ?

[@fixanddrive]

Pokazuje je we filmiku: kzbin.info/www/bejne/iafHiauYeKxkiJo

[@jacekfajkis1237]

@@fixanddrive dzięki ,ale szukałem u siebie w książce i nie mogę znaleść tęgiej informacji ,znalazłem na angielskich forach i wychodzi na to ze do R20A2 jest: Intake: 0.21-0.25 mm (0.008-0.010 in.)
Exhaust: 0.28-0.32 mm (0.011-0.013 in.)

[@MarcinKfilmy]

@@jacekfajkis1237 Podpinam się pod pytanie Czy takie same wartości powinny być dla slnika R20A2 cr-v 2.0 2010 rok ?

[@MarcinKfilmy]

Już mam Intake: 0.21-0.25 mm (0.008-0.010 in.)
Exhaust: 0.28-0.32 mm (0.011-0.013 in.) to są wartości do silnika 2,4

[@hzmusallatt]

My honda stepwagon in 145km never done valve adjustment still good sound but l will try do it.😊

[@dirtydan-OG]

Witam. Moja Hanka R20A3 ma 160000km i dopiero zabieram się za zaworki, ponieważ dopiero teraz słychać delikatne stukanie. Robię nią 40000km rocznie autostradowo więc myślę że wcześniej nie było potrzeby.

[@johnwesley3885]

Most likely the difference in recommendations for valve adjustment is based on 43,000 miles vs 100,000 kms.

[@kubaSWAT]

Witaj kolego, ską∂ masz wartosci luzu dla silnika R20A9? znajduje sprzeczne informacje...

[@fixanddrive]

Z for internetowych.