HOW TO APPLY OSMO POLYX.

  Рет қаралды 15,383

Willow Studios

Willow Studios

Күн бұрын

Пікірлер: 30
@ogwoodworks
@ogwoodworks Жыл бұрын
I normally apply it the way you have shown, but after doing so, I noticed that Osmo does not provide very good protection against spills and scratches. Then I actually read the instructions. Osmo recommends that you don't wipe off the excess after the first 2 coats. For best protection they say to apply the first 2 coats with a thin nap roller or brush as opposed to a rag or buffing pad, then let it dry for 8-10 hrs without wiping it off. After the second coat, sand lightly if needed and finish up with 1-2 additional thin coats applied with a cloth or buffing pad. I must say it makes for a much more durable surface which is still beautiful. Who'da thought reading the instructions could make such a difference?? For an art piece that won't see any spills or scratches, I'm sure it doesn't matter. But if you're finishing a table top or any surface that may get liquid spilled on it, it makes a big difference in durability to apply it the way Osmo recommends.
@jayc8844
@jayc8844 Жыл бұрын
100% agree, I use a foam roller for the first two coats and get a very even finish that water can't penetrate. Zero water rings.
@diaryofafounder
@diaryofafounder 4 ай бұрын
When you say sand lightly, is it okay to sand with an abrasive sanding block with a grit of let's say 360-500?
@umranhu
@umranhu 2 ай бұрын
How long do you wait before applying 2nd coat ? Instructions say up to 24 hrs which means could be 3 or 4 days before your finished. Ordered this for new oak handrail and base rail. I thought 2 coats would be fine but reading thos now concerned may need double that. As its handrail just concerned about durability and ease of cleaning as kids will no doubt get it dirty
@ogwoodworks
@ogwoodworks 2 ай бұрын
For furniture pieces, I’ve never used more than 2 coats of Osmo oil and it’s stood up very well. I leave the first coat for 12 hours, then apply the second and leave it for 12 hours before touching it. Thin coats are better with this product. Don’t leave oil puddling on the surface. Wipe off any excess if you apply too much. The beauty of Osmo is that you can do spot repairs without having to sand down and refinish the entire thing. I’d start with 2 coats and see how it goes. If it starts to look worn, just apply another coat to freshen it up.
@umranhu
@umranhu 2 ай бұрын
@@ogwoodworks thanks thats the plan. Just to be safe ill wait until next day for 2nd coat
@zxresa
@zxresa 10 ай бұрын
Hi I have just sanded the floors with 60 grit, would it be OK to apply osmo on that? Many thanks
@festivecheer9761
@festivecheer9761 5 ай бұрын
Can I use microfibre cloth’s for this job?
@HarryPanther
@HarryPanther 3 ай бұрын
Hi, is Osmo UV protection oil (clear matt/satin) any good for protecting pine that is charred, scrubbed (shou sugi ban) and then dyed with vibrant colours?
@sw_909
@sw_909 6 ай бұрын
If you did encounter a bad job, what type of sander would you use to remove the hard wax oil and start over? I used Osmo 3041 (the one with the white pigment) on my oak floor and it left a horrible white cloudy sheen because I put too much on.
@trdguy82
@trdguy82 Жыл бұрын
I had the painter apply this in our new build cabinetry. The painter put it on heavy in spots where I can see runs and surface glossiness. I no longer want them touching the expensive cabinets. Is there a way to redo or repair their terrible application?
@willowstudios323
@willowstudios323 Жыл бұрын
It’s possible to sand it off and start again, it will clog your sandpaper up initially but once you’ve got rid of the majority of the residue you should be able to finish sand it then reapply the osmo in the correct manner. Hope this helps. Jake.
@denverslinn
@denverslinn 10 ай бұрын
A scraper, perhaps?@@willowstudios323
@douglaslassance
@douglaslassance 6 ай бұрын
Any trick for disposing of left over oil?
@chippysteve4524
@chippysteve4524 5 ай бұрын
Keep the lid clean and put it back on properly. Even if it eventually skins over you can still peel that away and continue to use it.
@shanecummins5108
@shanecummins5108 Жыл бұрын
Great video. A question you might be able to help me with. I want to use this on a batch of hardwood coaster I've made and I'm just wondering approximately how long it takes to dry to the point where I could turn them over to do the other side. Thanks. Shane.
@willowstudios323
@willowstudios323 Жыл бұрын
If I’ve got stuff to oil both sides what I tend to do is make a little jig up where I screw several screws through some ply to suspend it in the air, the important thing is to file the end of the screws off so they don’t dig in to the work piece
@shanecummins5108
@shanecummins5108 Жыл бұрын
@Willow Studios Thanks for the reply. What I'm wondering is, if I finish both sides at the same time and suspend it on the jig, will the screws leave an imprint on the finish, or is that avoided when wiping off the excess?
@chippysteve4524
@chippysteve4524 5 ай бұрын
Read the instructions on the tin like a grown up :-)
@amhjoinery2060
@amhjoinery2060 Жыл бұрын
I don’t wipe it off after it’s tacked up😳learnt something today
@willowstudios323
@willowstudios323 Жыл бұрын
Happy to help !
@patrik6045
@patrik6045 Жыл бұрын
Thank You, keep it up 👍
@Samlol23_drrich
@Samlol23_drrich Жыл бұрын
Nice sander. Good luck building a following. I know how much time it takes so I’m subscribing to help you out. Good luck.
@willowstudios323
@willowstudios323 Жыл бұрын
Thank you I very much appreciated the support
@robohippy
@robohippy Жыл бұрын
If you are going to blow it off to remove dust, do that outside. That wood dust will be floating around the shop for several days.
@willowstudios323
@willowstudios323 Жыл бұрын
Thank you for that tip I’ll be sure to do that next time!
@upshiftgo
@upshiftgo 2 ай бұрын
Several minutes not days
@philvfilms
@philvfilms 6 ай бұрын
But for 50 meters square that would take a long time
@CrazyManwich
@CrazyManwich 22 сағат бұрын
No, you have been applying it wrong! Just kidding. The first time I used it on furniture, I had my 8 year old daughter assist and she was rather generous with the amount. Still a nice looking finish but not as smooth. Now I use an old orbital sander blocking it dust collecting ability and using a white 3M pad, let it sit for about 10 minutes then burnish it off using the orbital and a clean white 3M pad. It is so smooth after that.
@boyleroy
@boyleroy 8 ай бұрын
Goof stuff.
How to Apply OSMO PolyX Oil
16:23
Matt Estlea
Рет қаралды 429 М.
Wood Finishing with Osmo Polyx-Oil
11:17
Tools for Working Wood
Рет қаралды 63 М.
УЛИЧНЫЕ МУЗЫКАНТЫ В СОЧИ 🤘🏻
0:33
РОК ЗАВОД
Рет қаралды 7 МЛН
TopOil | Application onto a live edge table
5:41
Osmo Canada
Рет қаралды 20 М.
My Favorite Wood Finish - All Natural, Quick and Easy.
6:41
Craftswright
Рет қаралды 86 М.
A genius trick no one shows
14:47
Bent's Woodworking
Рет қаралды 560 М.
How to apply osmo polyx hardwax oil to furniture
17:10
Isak Ziegner
Рет қаралды 84 М.
Osmo Polyx Raw
4:17
HillbillyChic
Рет қаралды 7 М.
Osmo Polyx Oil - Before you Buy
4:01
Wood Finishes Direct
Рет қаралды 138 М.
Osmo Polyx Oil Rapid- how to Oil a Wooden Floor
15:37
Phil Beckwith The Professional Painter & Decorator
Рет қаралды 7 М.