Look next part here, click link: • How to assemble engine... Look previous part here, click link: • How to assemble engine... How to assemble engine VVT-i Toyota Part 29: Camshafts
Пікірлер: 28
@therealspixycat3 жыл бұрын
Is pre lube the cleaned bearing preferred before you put the bearing caps on? This way it is metal on metal. I don't think that the oil you apply after locking all the nuts will lube those bearings
@mdbadalmiah68085 жыл бұрын
Thank you sir 🇧🇩🤝
@kbengson91635 жыл бұрын
Questions Peter. Why is it important to remove the excess oil from the camshaft and bearing plates etc before installing, then you added oil back after torquing all the bolts? As long as the parts are clean before install it seems like any excess oil would help lubricate all the parts upon initial restart of the engine? The motor oil will be splashing around on all the parts anyway once the engine is started right? Thx
@PeterFinnTheCarDoctor5 жыл бұрын
I have to see bearing points status, maybe bearing areas are worn out or scratch
@kbengson91635 жыл бұрын
@@PeterFinnTheCarDoctor Oh okay, thank you. I understand, i wasnt thinking about it from that perspective.
@jh0nny_350z10 жыл бұрын
However, thanks to your videos you made me save a lot of money ... Thank continues ... :)
@PeterFinnTheCarDoctor10 жыл бұрын
Thanks.
@nasasiragodeth70112 жыл бұрын
So amazing u are a good teacher
@PeterFinnTheCarDoctor2 жыл бұрын
Thank you! Cheers!😀
@oscargarcia25636 жыл бұрын
So is 15nm for the small bolts and 25nm for the bigger bolts?
@PeterFinnTheCarDoctor6 жыл бұрын
Yes
@amitgangs4 жыл бұрын
Nice job man. Respect
@PeterFinnTheCarDoctor4 жыл бұрын
Thank you for the comment. I really appreciate it. Will be discussed further. 😃👍
@jh0nny_350z10 жыл бұрын
Good! What kind of oil did you use?
@PeterFinnTheCarDoctor10 жыл бұрын
Hi. Mobil 1 rally synthetic.
@jh0nny_350z10 жыл бұрын
Thanks!
@davidromero24774 жыл бұрын
Dissamble 12mm and assembly 13mm?? 🤔
@elhuachedesalgueromichuaca56972 жыл бұрын
Nice video thank you
@PeterFinnTheCarDoctor2 жыл бұрын
Welcome 😊
@elhuachedesalgueromichuaca5697 Жыл бұрын
@@PeterFinnTheCarDoctor how many pounds can I give it on the small ones?
@juliocarlosmartinez60452 жыл бұрын
Thanks a Lot,sir
@PeterFinnTheCarDoctor2 жыл бұрын
So nice of you
@juliocarlosmartinez60452 жыл бұрын
@@PeterFinnTheCarDoctor You are very Smart ,You help me to much ,thank You
@vinnienauta6 жыл бұрын
How many lbs?
@PeterFinnTheCarDoctor6 жыл бұрын
Hi, I will check...
@PeterFinnTheCarDoctor6 жыл бұрын
Here, Two steps: 1) 40 lbs and then also 2) Angle tighten a further 90 degree
@oscargarcia25636 жыл бұрын
40 lbs + and additional 90 degree angle is for all of the bolts or just the small ones?
@perrysouvana11374 жыл бұрын
Speak proper English and please use foot pounds not metric system