HOW TO BEND COPPER PIPE part 2 tutorial on how to bend offset bends in copper tube using a bender

[@saleh8944]

To the thumbs down folk who obviously didn't understand or fully appreciate the best pipe bending videos out there: I would suggest you pay someone to do it for you as Derek is far and away the best instructor on this subject :)

[@mikebarron4929]

I've been plumbing 37 years and I've not long found your channel and can say honestly if all tutors were as straight to the point and clear in there instructions as yourself then the training industry would be much improved your vids are spot on with little faff and lots of good knowledge

[@tomkatgastraining]

Thanks for your comment and watching cheers

[@phasedout6769]

Honestly the most helpful video on bending I've seen. Hats off. Time to mark my bender 👍

[@hdhanji8006]

Great tips thrown in Derek... measured properly with no unnecessary pipe wastage 👍

[@johnswilley6764]

Thank you Sir! I'm going through your videos, just got to #2, getting ready to make a Cu pipe dryer/receiver setup for my compressor. You have produced an excellent stock of info. From Orlando, Florida, U.S.A. thanks again, and best wishes!

[@mj0n4id36]

Truly amazing. Great tips given by a great teacher. The making use of a template and solder is genius. Marking out the centre of the pipe was a great tip too. I’m going to create a template, laminate it and keep it with my pipe bender. Thanks Derek 👍🏻 Asian Jon. Training.

[@mohammednadeem7274]

Another well presented video with very valuable tips to help with the pipe bending, I love the drawing with the angles, the solder was a well cool tip to get the bends and angles correct. An excellent video once again derek.

[@Agopper]

Great learning video as usual and thanks for for sharing your knowledge to newcomers, all your video are very educational for new entries in the trade cheers derek

[@MarcusT86]

Thanks for taking the time to make these. Great stuff mate!

[@davyogi9796]

Thanks Derek, at least you have shown that sometime we can over bend the pipe, marking the bender and another great tip, a bit different to when I was tault with 2 metal folding rules.

[@AJ-cw9rb]

As always Derek, great Video, keep it up mate 👍

[@TheRumpusView]

Thanks very much for this. It is just what I need, except I need to do a 60mm offset on 22mm pipe. I need to work out what the minimum offset is, I hope that a 30 degree bend is possible. Good camera work here. Well done.

[@willlomas2725]

Very informative Derek .....Thanks.

[@joebaikaikamara7509]

Great tutorial lesson

[@rivkiroyde4362]

Thanks Derek great video 👍👍👍

[@allanfuller7293]

Please tell me what pipe thickness you use. I bought a Rothenberger Multi-Bender and when I bend pipe it cracks. I want to start practicing pipe bending. Thank you

[@monikanader9454]

Another great video👍

[@fredjennings9268]

Informative... thanks for giving you time👍

[@creditlink]

Hi is this really a 30degree angle because it looks more like 150degree?

[@ashkanrajabzadeh9632]

That’s perfect boss

[@Dreancaidi]

How do you bend 1 inch copper pipe?

[@patricklynch2731]

Does anyone show how to bend 22mm pipe. What measurement do you come back to pull a 90deg

[@1Monaghan]

Oh no the dreaded saddle bend next

[@davidjingga8356]

Hi, does anyone know how to bend flat copper pipes? I understand I'd have to stuff the flat copper pipes with, like, fine sand so that kinks won't form when bending. But is there a specific tool to bend flat copper pipes with?

[@rotarurazvan8792]

You are great, clever...

[@jamiel6482]

yes lads

[@markroberts6864]

Cheers

[@koliakolian810]

Good

[@M20DAN]

Tomkat👍🏻

[@secondchance4498]

chris Taylor