How to BOOST Table Tennis Rubber (Hurricane 3 National Fan Zhendong version) 如何灌油(狂飙3國行樊振東版本)

[@botao4456]

I usually use 3 layers of voc glue on rubber then apply 1 thin layer of wbg on both sponge & blade to stick them & seal off the gas from voc glue. Nearly same effect as true booster with almost no waiting time, but you need to reglue every week.

[@ttpassion]

Nice. Thanks for sharing!

[@bryanwells4063]

What is WBG?

[@KeiSan14]

Thanks for this video !

[@ttpassion]

You are most welcome!

[@deep7496]

Why leave protective film on while boosting. Some say to take off as it prevents rubber from curling. Also some say to boost on sponge directly and no need to put glue layer first. Your comments?

[@ttpassion]

Hi Dipak, thanks for the comment. Yes, the protective film does prevent the rubber from curling. It's my preference to keep the film on until after I cut the rubber to prevent amy accidental stain of glue or booster on the rubber surface. As for the layer of glue before booster, I find that it aids in removing the layer of dried glue for reapplication of booster in future without damaging sponge and rubber. Hope this clarifies. Cheers!

[@deep7496]

@@ttpassion I have just boosted my H3N provincial blue 39 brand new with seamoon. I took the pre glue layer off first but it was difficult to take off and next time I think will leave on. For my first boost layer I kept film on rubber and it didn’t dome a lot but on peoples advice I took film off before I applied 2nd boost layer. It dined more after this application. It’s been 28 hours since 2nd layer and has started to flatten out slowly but not quite flat so I’m going to wait another 6-7 hours or wait till tomo morn which will be 48 hours after 2nd layer and then glue onto blade. By tomo morn it should be much flatter. Is there any advantage or disadvantage of waiting longer? Obvious advantage is longer u wait the flatter rubber will be hence easier to glue on blade! I thin k in hindsight next time I will keep film on till I cut on blade as looking at rubber it doesn’t have than brand new look as film has been off it. I like that feeling of peeling form off when it’s on blade.

[@ttpassion]

@@deep7496 thanks for sharing! Indeed the longer you wait the flatter the rubber will become and easier to glue. I can't think of any advantages or disadvantages for leaving it longer. The effect of the booster would already been absorbed into the sponge already. The only thing I struggle with is to be patient and wait for few days before being able to use the rubber. 😆

[@deep7496]

@@ttpassion I’m the same I don’t have patience but I’m not training till tomorrow so I may as well wait till tomo and glue on when flatter. This is my second time boosting. I was given a used H3N provincial OS 39 to try 3 wks ago so I boosted with 2 layers of seamoon, that was my first ever time boosting. I couple days ago got myself a new provincial BS 39 to now try and I have a new OS prov 39 on way which I will test at later date and see which I prefer. This is also my time trying hurricane as previously used D09C. I very much liked the used sheet I was given so if i continue to like I think I might have made my transition over to hurricane.

[@nicopacheco9083]

Should you also boost your backhand rubber as well or just the forehand? I have Hurricane Neo 3 National 37-degree 2.10mm backhand rubber and I wanted to know if you should boost it or not.

[@botao4456]

You only boost if rubber hardness is more than 39. Less than it there is no point boosting since the effect is minimal.

[@nicopacheco9083]

@@botao4456 great Thank you for the information

[@TOMATSTAR]

Hey whats the diff between h3 neo commercial and provincial blue and national blue is it much diff please explain (no boosting on all)

[@lhduy_vn]

Can I replace the glue you have with Free Chak II ?

[@ttpassion]

Hi LH Duy, yes for the glue you may use Free Chack.

[@brostv4029]

Hi, is it okey if i will use Haifu speed glue instead of water-based glue + booster oil?

[@ttpassion]

Hi. Thanks for the question. If you not planning to join any competition with very strict racket control then it's fine.

[@paknofriadi1877]

Apakah DHS Hurricane National Signature mempunyai tingkat kekerasan spon yang sama dengan Nittaku Hurricane Pro III Turbo Blue???

[@gxtvwang]

I have not found the video about the gluing of the boosted rubber onto the blade, have you already posted it?

[@ttpassion]

Hi Gustavo, it's not uploaded yet. Will be posting it be end of this week. Cheers.

[@ttpassion]

Hi Gustavo, had uploaded the video on gluing of this rubber. Here's the link for the video: kzbin.info/www/bejne/e6C0mWqrrpapaqs

[@gxtvwang]

@@ttpassion Hi, thanks for warning! Congratulations for the nice video

[@sareythun69]

How can I find store for buy genuine herricane 3? i’m trying find on taobao but i still afraid for fake product. You can recomond store?

[@ttpassion]

Hi, I purchase frequently from taobao and here are some tips that I can share in order to buy genuine items from taobao. Always check the shop rating and review comments that people leave. Only buy from shop with excellent rating. Avoid buying it if the price looks too good to be true. Also, look at how long the shop has been on taobao. It's safer to buy from shops that are around for a long time.

[@sareythun69]

@@ttpassion thanks you.

[@NoTengoIlusiones]

Why you Boost ? Only used Butterfly , Yasaka and Tibar rubbers. Can you make a video to explain ? Thank you

[@ttpassion]

Hi NoTengIlusiones, thanks for the question. Boosting of rubbers are common for chinese rubbers such as Hurricane 3. The effects of boosting the rubber in short is to increase the tension of the sponge in order to create more spin, speed, and feeling. In my opinion, this effect is about 10 to 15% after boosting. If you are using tensor rubber, normally it is already pre-boosted or tuned during manufacturing to increase it's tension. Hence, there's no need to boost a tensor rubber. Thanks for the suggestion too on creating a video about rubber boosting. I will add this topic to my content creation list too. 😁

[@doydoycarlo3455]

do i really need to boost my H3 Neo (orange sponge) 40 degree 2.2?

[@ttpassion]

Hi Doydoy, I'd recommend to boost it but perhaps only 1 layer as your sponge is 2.2mm.

[@cia3_294]

@TT Passion how often do i need to reboost

[@ttpassion]

Hi. If you play 2 to 3 times a week, I would suggest reboost every 2 to 3 months.

[@astamak2566]

Is the layer of glue before boosting really necessary? I’ve heard that the rubber will absorb the booster better without putting that extra layer of glue in the beginning Also when reboosting my H3 Blue sponge 40, should I have one or two layer (First time reboosting, first put on 2 layers of Haifu sea moon regular)

[@ttpassion]

Hi astamak, the rubber will stick better onto the blade with the extra layer of glue in the beginning. Reboosting can also apply 2 layers.

[@JakePlayz07]

How do you find the player version Hurricane 3 compared to the regular Neo national? Is it worth it?

[@ttpassion]

Hi. I think perhaps at my skills level, I can't really feel much difference compared to Neo national. Hence, I feel it is not worth it to use as a permanent option.

[@JakePlayz07]

@@ttpassion thanks, is the durability any better? If not I think I’m just going to go Neo national

[@janeccq]

Hi sir, may I know how many layer of glue is preferred (without apply booster)? Says use the same glue as yours, the DHS.

[@ttpassion]

Hi Jane. Thanks for the question. For me, I will only apply 1 layer on the blade and 1 layer on the rubber. For me it is good enough though I heard before there are players that apply 3 layers of normal glue also.

[@janeccq]

@@ttpassion thanks for your suggestions

[@astamak2566]

Will haifu seamoon national yellow work well with DHS Hurricane 3 Neo Provincial Blue sponge? How many layers do you think is necessary if the sponge thickness is 2.15mm?

[@ttpassion]

Hi Astamak, yes it will work too. I recommend max 2 layers as it is already 2.15mm. Boosting will make the sponge thicker and run the risk of exceeding the legal limit of 4mm (sponge with surface) in competition.

[@astamak2566]

@@ttpassionthank you for the response. If you don’t mind me asking one more question, how often should i reboost if I play around 1-2 hours per week? Also which sponge hardness of DHS Hurricane 3 Neo Provincial Blue Sponge should I get, 39, 40 or 41?

[@huh1321]

can i apply booster or baby oil johnson on chinese rubber like LOKI or 729 Friendship?

[@ttpassion]

Hi. Thanks for the question. Yes you can booster those rubbers too.

[@huh1321]

@@ttpassion I have another question , can I apply booster on the Chinese rubber that I have been using it on my bat for about 1 months ?

[@ttpassion]

@huh1321 hi. Yes you can remove it and apply booster before regluing.

[@huh1321]

@@ttpassion do I have to reflux the bat?

[@taytayxhron4855]

Hi I'm planning to boost hurricane 3 neo provicial blue sponge hardness is 41 how many layers of booster do I need?🤗

[@taytayxhron4855]

2.15mm

[@ttpassion]

@taytay xhron Hi taytay xhron, I'd suggest 2 layers first and check the total thickness before applying the 3rd layer as your sponge is 2.15mm. Too many layers will thicken your sponge and might result in your rubber becoming more than 4mm in total, which exceeds the acceptable limit when competing in competition governed by ITTF rules and regulations. If after 2 layers it is still well within the 4mm limit, then go for the 3rd layer. That's what I would do. Hope this helps.

[@marina_bio]

This brand of booster is forbidden ?

[@ttpassion]

Hi Paul, boosting of rubbers are all forbidden in official tournaments regardless of the brand.

[@marina_bio]

@@ttpassion there is one Brand called haifu came out with VOC free booster oil. I was told that this oil is not forbidden.

[@ttpassion]

@@marina_bio Hi, accordingly to the law of table tennis, rule 2.04.07 states that racket covering (rubber) shall be used without any physical, chemical or other treatment. Therefore, any booster oil is actually not allowed. However, in your case if it's VOC free, it's difficult to be detected during the test. But by the law, it is illegal. Sharing this website here which explains the law: www.allabouttabletennis.com/table-tennis-bats.html

[@marina_bio]

I saw some one using boosted DHS 41 degree rubber, it required some technique to loop. The effect will be like banana curve shot!

[@ttpassion]

@@marina_bio yea. Boosting the rubber will generate more spin. So it can be really an advantage. But have to ensure don't boost it till its thicker than 4mm. Most local tournament doesn't do racket control checks, but if the rubber is too thick it might arouse suspicion from the official to do a check on your racket. But this will not be a concern if there's no plan to join any tournament.

[@kevinokeeffe5764]

Where could you purchase this version of hurricane ??

[@ttpassion]

Hi. For this particular piece I got it from a fellow player in singapore. But it's mainly available in China only.

[@lhduy_vn]

Is it normal that instead of curving straight my rubber is curving diagonally :)))? I'm boosting H3 41 Neo

[@ttpassion]

Hi, not that I have seen before. Did you brush the oil diagonally?

[@lhduy_vn]

@@ttpassion I spread horizontally. But some lines at the end I spread perpendicular to what I spread, I still spread again those space parallel to horizontal line. That is the 2nd layer. I think the first layer I boost too thin that I hardly see any curves

[@ttpassion]

@@lhduy_vn hmm.. i think its okay. As long as the oil gets absorbed into the sponge. Should be fine.

[@jemianandeska757]

Ada yg tau bahan pembuatan booster yg mahal mahal seperti dianchi, falci loong? Apa bedanya dengan baby oil yg krliatanya sama bisa melentingkan karet?

[@x-wn8hl]

This version has name printed on sponge?

[@ttpassion]

Hi. Thanks for the question. Yes, his name is printed on the sponge.

[@lhduy_vn]

Hey, I have the national version of H3 (Wang Chuqin, 41.5), how many layers would u recomend and how long should it be re-boosted if using Kai Lin (exact thing as u)? I play like nearly 20 hours a week if training or 10 hours regular.

[@ttpassion]

Hi. I'd recommend 3 layers too. And reboosting once every month as you are playing very often.

[@lhduy_vn]

@@ttpassion i have 1 H3 38 to use as backhand what would u recommend ? :”)

[@duchuyqtdn]

Bác mua dầu tune kailin ở đâu vậy có share đc ko

[@lhduy_vn]

@@duchuyqtdn em mua đặt hàng online từ Trung Quốc đến Canada (TTNPP hoặc prottvip) anh ơi. Em ở nước ngoài ạ.

[@andreivarlam2752]

Hi! What* s fan zd using rubber on backhand ,,,, now and befor?

[@ttpassion]

Hi Andrei, from what I know he is currently using Dignics 09C for backhand. Prior to this was Dignics 05.

[@andreivarlam2752]

@@ttpassionok thanks

[@andreivarlam2752]

Is it boost for dignics 09c?

[@ttpassion]

@@andreivarlam2752 I'm not too sure. But I don't think so. Normally, they only boost the Hurricane rubbers

[@ngwilliam3752]

Hi..where did you buy the Kai Lin Booster Oil ? From Tao Bao ?

[@ttpassion]

Hi William, I found it on TaoBao and subsequently used Ezbuy Prime wishlist to buy and ship for me previously. But Ezbuy Prime no longer does wishlist item. Now have to find own 3rd party forwarder to help ship into Singapore.

[@ngwilliam3752]

@@ttpassion I also think to buy it from TaoBao to Malaysia..but I concern about the custom check it and not allow to export/import 😁

[@ttpassion]

@@ngwilliam3752 I see. I think depe ds on your forwarder whether they confident to ship it in for you. Can try checking with the forwarder that you plan to use.

[@francescogalvao6369]

Can you say where did you buy this rubber since I heard it is really difficult to find these player rubbers?

[@ttpassion]

Hi, for this piece I got from some other players in Singapore. The only other way I know to get this is via China Taobao online shopping app.

[@bryanwells4063]

It's not worth it they are a scam. Fake national player rubber, fan zhendong would not sell his rubber and DHS wouldn't sell his personal rubber either.

[@lapiskamay]

great review man! is boosting still allowed in tournament play in SG?

[@ttpassion]

Hi lapiskamay, if the tournament follows ITTF rules then no. But it's not easy to detect unless you boosted very heavily and used VOC booster.

[@nathanlee8494]

@@ttpassion what boosters are non voc? like falco tempo long? i have heard that non voc boosters such as baby oil don’t have as much effect though, i’d love to hear your thoughts.

[@ttpassion]

Hi Nathan, baby oil not specially made for table tennis rubber boosting so I don't think will be good to use for boosting. Yes Falco Tempo long is VOC free too. Most of the booster available nowadays are voc free. There are other brands like Haifu also.

[@nathanlee8494]

@@ttpassion haifu sea moon also non voc? are any health hazards tho from inhaling the smell? thanks for the trsponse

[@ttpassion]

@@nathanlee8494 I think haifu and seamoon have very low level of voc which is not really detectable at tournament racket control. In terms of health risk, the oil is still chemical and not of natural oil. Therefore, inhaling it definitely is harmful. Hence, when boosting it will be best to have a well ventilated space and avoid inhaling the smell from the oil. I found this article related to boosting from Pingsunday really useful. Sharing it here for all to understand more about boosting. pingsunday.com/tune-chinese-table-tennis-rubber/

[@Zai155]

hi, may i know if i should boost my backhand rubber also?

[@ttpassion]

Hi Huzaifah, thanks for your question. May I know what rubber are you using for backhand? As there are some rubbers that do not really need any boosting.

[@Zai155]

@@ttpassion im using dhs hurricane 8-80 for my bh

[@ttpassion]

@@Zai155 Hi, yes you can boost it too if you want to add more spin. But may not need 3 layers. 1 layer should be okay.

[@Zai155]

@@ttpassion tqsm!

[@ttpassion]

@@Zai155 you are most welcome.

[@александрдворник-б7к]

Где у вас купить этот бустер

[@ttpassion]

Привет, спасибо за вопрос. Я купил его в приложении для покупок в Китае под названием Taobao. Но вы также можете использовать другие бустеры, которые могут быть доступны в вашей стране, например такие бренды, как Seamoon или Haifu, которые продаются в большинстве магазинов настольного тенниса.

[@Fifaplayer379]

What if I put more than 12hours?

[@ttpassion]

Yes, you can do that too. The longer you wait, the rubber will flatten more and it will be easier for you to glue subsequently. Effect wise, I really don't feel much of a difference though.

[@Fifaplayer379]

Thanks

[@peepsaklop1456]

Is it legal for booster?

[@ttpassion]

It's supposedly not allowed for competition. However, there is no way the officials is able to check if your rubber is boosted. This is also the same for the professionals.

[@882828jc]

May I know after you boosted the rubber, how long it will last ? Also can the same rubber reboots again ? If so, how do you line it up, is hard ,isn.t it ? Thanks

[@882828jc]

I need answer..not thumb up...Bro...

[@ttpassion]

Hi TSO, thanks for the question. I play typically about 4 hours a week, and the booster effect last about 3 to 4 months before i boost it again. When i reboost it, I would only apply 1 layer of booster instead of 2 or 3 layers. After boosting, to line it up more easily, will need to wait for a few days for the rubber to flatten. Otherwise, just need to be extra careful and paste the rubber slowly starting from near the handle with the middle part of the rubber and slowly roll upwards.

[@ttpassion]

Hi bro, no worries.. the answer is little long. Hence, it takes awhile to type after I clicked on the thumb up.

[@882828jc]

@@ttpassion Thanks.Pro..thank for uploading.We can learn a lots.

[@ttpassion]

You are most welcome..Happy to share

[@орпвплл]

Why do you think bubbles appear?

[@mgarzonf]

🌎🇪🇨🙂👍

[@vadevictor6269]

You can't buy pro player rubbers and taobao sells fake or boosted commercial

[@AustinHowd]

Yes you can