I've disassembled these, but haven't built one yet, so thanks a million for doing this!
@Shedtune_Russ10 ай бұрын
No problem 😉👍
@neuralyser10 ай бұрын
What you call the spacer Russ I call a seal retainer, I only mention it cos it's used for both GP and LI cranks, might cause some confusion as there's a different spacer entirely to add to theses components if fitting to LI/SX type crank (as I'm sure you know but for the benefit of anyone doing this job for the first time) Nice vid mate
@Shedtune_Russ10 ай бұрын
Yeh u r right, I did think about that after I’d filmed it lol… 😀👍
@peterpartington836710 ай бұрын
GOOD VID RUSS , SIMPLE JOB , IS THAT WHY YOUR DOING IT ? AND NOT DOM ! 👍🏻😎
@Shedtune_Russ10 ай бұрын
😂😂😂 yeh, and cos Dom has fat fingers lol 😂
@peterpartington836710 ай бұрын
@@Shedtune_Russ IT'S ALL THEM BLOODY JAFA-CAKES , ! FAT FINGERS 👍🏻😎
@shedtune8110 ай бұрын
🤣🤣
@andywalsh118510 ай бұрын
Lovely bearing lubrication action going on 👍 nice video tho Russ although Dom would have done it better 😉😘
@Shedtune_Russ10 ай бұрын
Lol 😂
@shedtune8110 ай бұрын
🤣🤣 the viewers are always right 👍
@stevebgp20010 ай бұрын
Great vid as always, have you been polishing!! ready for Sunday? You’re very good with that finger!! Do you flick those pages of the workshop manual that hide in the corner of the garage 😅😅
@Shedtune_Russ10 ай бұрын
Always 😉
@4th_Lensman_of_the_apocalypse10 ай бұрын
Nice informative vid as usual gents! I dont understand how come you had room for the bearing in the fridge? Did Dom drink all the beer? 😄🍻
@Shedtune_Russ10 ай бұрын
Cos it’s a freezer lol 😂
@4th_Lensman_of_the_apocalypse10 ай бұрын
@@Shedtune_Russ he ate all the ice cream? 🍦
@Shedtune_Russ10 ай бұрын
@@4th_Lensman_of_the_apocalypse u know it
@supereibarperformances550310 ай бұрын
Excellent work señor. Great quality video as always. I always put the little 'legs' hanging from the edge of the table, so I don't put them under any stress when I help the seal in (some people really get excited with the hammer! LOL 😉) I do have a question what is your opinion on these UNI mag housings?
@Shedtune_Russ10 ай бұрын
The UNI mag housing seems ok, it’s nice and clean with very little casting marks which I like. The bearings and seals all fitted well so unless the Aluminium in porous it will all be good. Once I’ve done a leak down test I’ll soon know. 👍
@cyclops-fpv10 ай бұрын
Nice video although Dom would have done it quicker😁
@Shedtune_Russ10 ай бұрын
😂😂😂
@shedtune8110 ай бұрын
🤣🤣
@waynesykes861110 ай бұрын
Can you say what tep are you looking at please
@Shedtune_Russ10 ай бұрын
For this build I went to 60 degrees C
@autodallee452710 ай бұрын
What's nice and hot ? You missed that little snippet of information from your otherwise great video.
@Shedtune_Russ10 ай бұрын
My ‘nice and hot’ is around 60 degrees c, but that’s just me.