How to Build a Winder Staircase

Рет қаралды 57,455

Күн бұрын

Пікірлер: 36

@timbirch4999 5 жыл бұрын

I like the way this stair is built - very efficient. Unfortunately, it wouldn't pass UK building regs, due to the narrow end of the winders coming to a point. They have to be just under 2 inches minimum (50mm) over here.

@kenskarpentry 5 жыл бұрын

Thanks. I wish I did make it 2”. The original stairs were about 28” wide super steep and about a 6” tread. I can only imagine how many people fell down those old stairs

@GaryThomsonJoinery 5 жыл бұрын

One day I might make a winder like you guys in the US, it is far quicker than here in the 🇬🇧, I’ve done a few videos on making them and we do it so different. Thanks for sharing 👍📐🔨

@kenskarpentry 5 жыл бұрын

Thanks

@hugeshows 3 жыл бұрын

Doubtful this would make code in most places in the US. Ignoring being an 1/8" over on max riser height, the winder section tread is allowed to taper down to 0" and most codes I've looked at state a minimum of 6" at the narrowest part of the tread. The reason is obvious - misplace your foot at that corner, and you drop three steps instantly.

@cullenmcgrath9028 3 жыл бұрын

6” minimum at the narrowest point of the tread

@andyedge7912 5 жыл бұрын

Got to say thanks for this video im planning on doing the same job in the new year.

@kenskarpentry 5 жыл бұрын

Nice I hope your project goes well.

@arkansas1336 6 жыл бұрын

Excellent results, especially on the 'winders'!

@kenskarpentry 6 жыл бұрын

Thanks

@thomo74 3 жыл бұрын

Very neat & tidy ! Do you have a video of how you cut the staircase opening? I’d like to know how you remove the joists and ensure everything is Supported correctly.

@kenskarpentry 3 жыл бұрын

I think I’ve covered it in past videos

@loueber 5 жыл бұрын

Kudos to the worker that was wearing the proper resperator!

@kenskarpentry 5 жыл бұрын

Thanks

@donhuffer5167 2 жыл бұрын

Winders must be 6” at the narrow end. Minimum width of steps is 36”.

@donhuffer5167 2 жыл бұрын

Code riser height max is 7 3/4”. You must be in a no code area.

@louish.9414 2 жыл бұрын

I had no choice go 8” rise because of height of back basement door.

@vianneydavalos2501 2 жыл бұрын

Building code says minimum of 3 stringers

@louish.9414 2 жыл бұрын

I know code say 6” at smallest end what about winder end?

@louish.9414 2 жыл бұрын

I watch many videos on winders only bob Villa had it correct

@josho4971 5 жыл бұрын

Sorry it doesn’t look like that second step is 8” in rise hope there only temps or you will trip

@kenskarpentry 5 жыл бұрын

Good eye those were temporary. We put in some nice treads and risers.

@builderspluscustomhomesand2146 4 жыл бұрын

Even if it wasn't 8", 7 3/4 passes. Out here we have the (7-11) method. Also just because it's not 8" don't justify that someone is going to automatically trip solely based only on that. lastly in his video, he specifically states it's a temporary set of steps.

@josho4971 4 жыл бұрын

Builders Plus Custom Homes and Remodels Why put that much time into building a temp set of stairs . I build stairs for a living and take pride in my work . Do your math and execute the job like a pro. These guys just want to look important on you tube , Hey everyone look at what I built , then I come along and bust their balls for doing it wrong . Btw 8 1/4” step passes code 7 1/4 - 7 3/4 is ideal

@adammacer 4 жыл бұрын

@@josho4971 Passes code where? - the world is bigger than wherever you are.. Why put that much time into a temp set of stairs? Because they want better access to the upper floor than a ladder perhaps? Sounds like you just wanna sound important and 'I know it all' on KZbin..

@josho4971 4 жыл бұрын

Proof is in the pudding bud and your pudding is sub par. I build stairs and do them right . I don’t need a you tube channel to make money I do it in real life