How to cap off your Washing machine or Dishwasher valve

[@TheCatBilbo]

Nice one, it's the simple stuff we sometimes need illustrating. It's not just brain surgeons who need steady hands! 😁

[@JerryHargett]

Where do I get a washer

[@diyshop839]

Hi Jerry, You can purchase this from screwfix or toolstation.

[@traffk3149]

Your video has helped me alot. I wasn't sure what was needed and your advice has proved invaluable and saved us money. Thank you so much.

[@bigbark4627]

Nicely done, simple & to the point, excellent vid 👍 Still the same Screwfix code & only £1.59 in 2024 👍

[@stevesvids]

Nice one.... thanks. I knew what I wanted I just didn't know what it was called. Part number too... you're a star. Thank you. 🙂👍

[@stef2282]

brilliant! My tap valve broke & wouldnt stop the water so had to turn off the entire water and get one of these caps instead from my local screwfix! Life saver with the exact code!

[@diyshop839]

Hi stef, Sounds like one off those jobs, well done.

[@destroya125]

You are a gentleman and a scholar my friend!

[@jasbo7288]

Hi I have one of these valves and want to take my dishwasher out but the valve is stuck open and won't shut..is it best to force it or work it abit? Thx.

[@diyshop839]

Hi there, I wouldn't force it but best to try moving it both ways to make sure it can turn, If this doesn't work then turn off your mains water supply and fit a new valve.

[@brandonbird9940]

I have a y shape pipe with the hot water going to the dishwasher and cold to the washing machine, can i cap off the cold while the blue lever turned on? Will the pressure cause an issue?

[@diyshop839]

Hi there, If you can send some photos then I can assist you with the correct information. All the best Mustafa

[@JonP2008]

Amazing, thanks so much for sharing and including the part number.

[@mat176]

You saved me potential flood thanks

[@1yellowface]

Great video. Thank you 😊

[@diyshop839]

I would like to thank you for your positive comment, and the price of the product aswell, unfortunately some people have no idea.

[@nanceedee287]

So, how do I cap off the pvc drain that goes to the dishwasher? I want to remove mine, as we don't use it.

[@diyshop839]

Hi Nancee, There are two ways to do this one is to use solvent weld with a access plug, or you can use a compression fitting, both will be 40mm or 1 1/2". To pin point this you can send me some photos or a video and I can talk you through it. All the best Mustafa

[@sufc43]

Unscrew the blue tap?

[@diyshop839]

Hi there, Yes you can do that unscrew the lever, however in my experience what happens is that if you need the valve working again you can never find the screw and lever. Also people then use pliers to turn it on and off, then if there was a emergency to turn the water off, there is no lever and you would need to find the pliers which isn't as quick.

[@fullstack5461]

Excellent video , well explained and relevant information provided

[@amazonwarrior7126]

Thanks for this, I was not sure they sold cap for these valves, but now I know and will lock off my valve. I was very nervious about the valve being open

[@carolineramage7480]

Èxcellent video. Thanks!!

[@alanmoley320]

Thanks off to screw fix for 2 of these as mine are dripping in off position,saves me looking up the part number you star.

[@ericmilligan3]

Thanks, what diameter is that copper pipe please?

[@diyshop839]

Hi Eric, The copper pipe is 15mm Hope that helps.

[@ericmilligan3]

@@diyshop839 once again thank you. So, the gate on a 15mm pipe has a 3/4” thread?

[@diyshop839]

Hi Eric, The end of a washing valve is 3/4" however if its a isolation valve the end will be 1/2" Hope this helps.

[@garyfanticsfantastic9366]

You can also unscrew the blue/red lever and then remove the lever to alleviate knocking it to the open position 🎉

[@diyshop839]

Hi there, Yes you can do that, however if you want to reinstate the appliance you will never find the screw or handle. As a example when I have tried to turn a valve off especially in a emergency there hasn't been a lever in place so then you are in a lot more trouble, as this pipe may feed another water supply eg taps.

[@Emble64]

How to remove these caps? Just unscrew?

[@BigSister56]

i have a problem with a tee valve which does not have enough threads to totally seal it so water just come poring out

[@diyshop839]

Hi there, As long as you have a rubber washer on the blanking nut, then you shouldn't have a problem. However if the valve doesn't close fully or the thread has been cross threaded then you would need to replace the valve.

[@simonc4764]

I cant turn the blue tap clockwise to close off the water, do you know what happening?

[@diyshop839]

Hi there, Depending on which way you're valve is facing, I would try turning it the opposite way to the pipe and that will work fine. Hope this helps.

[@krstone24]

Question: my had my dishwasher unhooked so I can have a new one installed. I noticed when I drained my kitchen sink water would leak. If I cap it until my new dishwasher is installed will I be able to still use my sink?

[@diyshop839]

Hi there, Judging from what you are experiencing, I'm assuming you mean the spigot that is attached to the trap underneath your kitchen sink. If you have a blanking cap I would suggest fitting that to the spigot temporarily (but remember to remove before installing the new dishwasher) Alternatively, if you haven't got a blanking cap you could just put a bucket underneath the trap whilst awaiting the new dishwasher. All the best

[@justnarcisa2153]

Very helpful thanks

[@jimirons833]

Would you have a video to replace a faulty isolator valve for a washing machine

[@diyshop839]

Hi there, Unfortunately I haven't got a video for that.

[@FoxyLad]

I'm looking for something for the actual machine blue water hose end to stop any excess water coming out while moving washing machine any ideas thanks

[@diyshop839]

Hi there, When you disconnect the washing machine it will only be the water that is left in the pipe that will leak. However, if you want to get something to stop any water coming out the pipes what you could do is purchase a washing machine valve 3/4 inch and attach it to your blue inlet hose. Then turn the lever to the off position which will stop any water coming out of the inlet hose. With regards to the drain hose, you would need to disconnect that, disconnect the spigot and fit a blanking plug to the spigot. Finally add a jubilee clip around the drain hose and this will stop the water coming out. If you have a look at my video on fitting a blanking plug to a washing machine/dishwasher trap it should help. All the best Mustafa

[@soulreaver1311]

Can’t turn mine off can I turn it off by screwing the screw-on the blue cap

[@diyshop839]

Hi there, The answer to that is no, the screw is to attach the handle to the valve, I would try a little bit of WD40 and let it seep in for 1 hour before you can try it again, normally the screw gets clogged. If that doesn't work you can undo the screw and pull the handle off, you can use water pump pliers or pliers to turn the head of the valve A QUARTER TURN ONLY, DON'T FORCE IT and that will work. As a back up make sure you know where your STOP COCKS ARE.

[@unknownauthor2u]

thanks for a great video - I'm trying to install a cap but it still leaks no matter what? any ideas? the cap i have doesn't need me to push anything in like you do on your video

[@diyshop839]

Hi there, The best thing to do would be to replace the valve and olive, make sure that the power supply is turned off to your appliance, and that the main water supply is turned off before carrying out any work. Alternatively if the issue is that you are missing the washer that sits in the cap, then you would need to get one, they should be provided with the cap.

[@nenoschamany616]

No matter how tight I tighten the cap valve it still leaks, I even used the pipe tape and still leaking, any tip to stop the leak?

[@diyshop839]

Hi there, If you have got a rubber washer this will never leak, however if the actual valve is leaking from the nut itself you can tighten it slightly.

[@nenoschamany616]

@@diyshop839 I actually ended up putting a washer and it stopped the leaking

[@marcokernbach9408]

Hi, my washing machine service valve is broken and won’t turn off -(it’s an upright one) is there a similar item I can put on the end of the hose that connects to the washing machine? I think if I put a kink in the pipe and put some sort of cap on the end of that it will create less flooding and be easier to attach the new washing machine to the hose? Thanks!

[@diyshop839]

Hi Marco, What I would advise is that you find where your mains stopcock is and turn it off and then carry out your work, you can then replace your washing machine valve for a new one. All the best Mustafa

[@Lwbop]

Hi there. How come when you put the cap on there wasn't a build up of pressure? If the water has no where to go when the valve is open surely this would result in a leak or burst pipe somewhere else? I'm a new homeowner so perhaps this is a dilly question 😅

[@diyshop839]

Hi there, This is a fail safe method, if for example the valve was to turn on and you have capped of the valve this simply acts as a end of a pipe run. So there's no chance of a burst pipe or a leak. All the best

[@Lwbop]

Thanks a lot for clarifying :) @@diyshop839

[@JerryHargett]

i bought the cap but it did not come with a rubber washer

[@diyshop839]

Hi Jerry, I bought mine from screwfix and it came with the rubber washer, I would recommend buying it from there or if you get stuck try toolstation, otherwise you will find it difficult to find a rubber washer to match.

[@jonathansimmonds5784]

I wish everyone posting a video would watch it without sound before posting it, you make them far too long!!

[@diyshop839]

The video isn't too long the step by step guide is clear and concise. The video has audio which is essential for educational purposes. What I would recommend is that you watch a different video. I have a 100 percent positive feedback, I'm surprised about your comment.

[@davidm5975]

Did this video help you?

[@saphblue8171]

I'm very surprised about this comment 🤔

[@biggur5]

Im asking a slightly different question but can the blue lever be replaced? Mines disappeared and didnt know where to isolate the water from so turned it off from the mains when my washing machine was changed. Can i simply just push a replacement lever back on?

[@diyshop839]

Hi there, The answer is no, once you push the lever back on you will need a Phillips machine screw, I normally buy a new valve which is the easiest option and just swap over the lever and screw. All the best Mustafa

[@biggur5]

@@diyshop839 thanks buddy. Are they all standard size ?

[@diyshop839]

Hi there, Yes the valves are all standard size, however if you are buying one to replace the lever and screw, the non branded ones generally are the same, but some of the branded ones have a slight difference in the handle shape.

[@biggur5]

@@diyshop839 thankyou

[@katerainsford7327]

How do we remove this cap and if I do will i be able to install a washing machine?

[@diyshop839]

Hi Kate, With regards to the brass cap you just need to support the valve and undo the cap, making sure the handle is in the off position, then you can attach your inlet hose from your washing machine. Hope this helps feel free to contact me if you require any further information.

[@katerainsford7327]

@@diyshop839 thanks, I am trying the cap but it seems to be very stuff, are there any tools I could get to help?

[@diyshop839]

@@katerainsford7327 Hi Kate, What you need is a adjustable spanner and water pump pliers, and remember to turn it anticlockwise.

[@AG-mx7ot]

how did you end up removing

[@DhdjdjddjxxriejxixjdidjxD]

£2.89 now. Show inflation.

[@diyshop839]

Prices are expected to change depending on the time of purchase, also Prices vary from different suppliers.