How to change 2019/2020 Hyundai Elantra Headlight bulb replacement within 10 minutes.

[@Vanderrick06]

Thanks so much. This 36 year old lady right here changed her own headlight! I could cry. Thank you thank you!

[@janpetri9908]

Thank you! Other videos showed how to disassemble the entire front end of the car in order to change a light bulb. This worked beautifully.

[@peterlindvall7671]

IKR. Haha.

[@obadiahfields2615]

I was just looking at another video... Took the whole bumper off...I was thinking this is going to be a long day lol till I seen this. Thanks 👍

[@jacobpibbleton2077]

I followed the directions and got the job done quick and easy, thanks for the excellent tutorial!

[@stevenhickey326]

Good vid. I just finished doing this...on a 2020 Elantra. Step by step. Good lord! It took me 45 minutes. I had to come up through the wheelweel on BOTH sides. Even then my hands are numb from cramming them into extremely tight space. Thanks Hyundai!! Good luck with any other DIY doing this.

[@FlynProfessor]

I like this approach better than pulling the whole bumper and whole headlight assembly. Thank you for sharing!

[@unclefuncledan]

The dealership offered to get these replaced for $800+ for each separate bulb. This video makes me confident I can do it myself.

[@IIAnonymousYTII]

Any mobile mechanic on the planet would charge you $100 or less to do this job.

[@stevenhickey326]

Good luck , I hope you succeeded. I did...took 45 minutes but I got them.

[@dopestyle9191]

There's no way you did it that easy. I need to see more on how you did this

[@williamswanson7527]

it worked that way, had to have my daughter reach in, her hands, arms are smaller.

[@issacwhaley5720]

I just did it I was a little longer than ten minutes but if you have the patience it can happen

[@stevenhickey326]

You can do it. I just did it. Plenty of expletives , and my hands are still numb , but success. Took me 45 minutes.

[@JacobHaines91]

Thank you sir!!! You saved me so much time and money!

[@tydixson3334]

Man I went to Walmart this morning and they said they couldn’t do it cause we had to take the wheel off. So thank you for the trick to come underneath through the wheel well so thank you again!

[@chki1462]

I still hate Hyundai engineers..😂😂 But this was by far the easiest way to access and change the headlights. Thanks.

[@MsLaunt]

great video tutorial.. replaced all 4 lights. my DRL still isnt working for my right side.

[@bryanarthur2464]

I just did it and it worked. Thanks man!!

[@Azoth742]

You are the GOAT!!!!!

[@miklovin5683]

Did it work?

[@haroldwhitehurst6299]

I just did mine...thank you bro!

[@dominiquenewman]

Just installed LEDs (Fahren Termitor) on my sister’s Elantra and confirmed, very easy. Just pop the clips like in the video, and bam, easy access…..just not a lot of room so you’ll have to feel around a bit but still easy.

[@nickcavolli3072]

So im confused i ordered a 9005 led and it did not fit with my 2019 elantra. The lowbeam healights are on the outside and highbeams are on the inside. Lowbeam takes the H7 correct?

[@maddieswanson1608]

Just replaced my bulbs and they work great on low beam, but the driver side high beam doesn’t work. Any suggestions? Already switched sides with the bulbs so it’s not the bulb

[@timhogan8032]

There is a recall on that issue. Had to replace both of mine

[@Barnoldo2010]

Can you post a link to the led headlights?

[@funnyanmalvideos5093]

Where can I buy those little? Please?

[@nacholl1966]

The Hyunday Elantra 2019 and 2020 works with a single bulb and has inside the headlight housing a device with a plastic gear and a sheet that projects more or less light on the magnifying glass, meaking the difference between highs and lows beams. The failure is given that the plastic gear when receiving the heat from the bulb and it detaches from its base or loses adherence and this causes that a the system doesn't releases more or less light on the magnifying glass and the high light being affected. El Hyunday Elantra 2019 y 2020 trabaja con un solo bobillo y tiene internamente dentro de la carcasa del faro un dispositivo con un engranaje plástico y una lámina que proyecta más o menos luz sobre la lupa y marcando la diferencia entre altas y bajas. El fallo dado que el engrane de plástico al recibir el calor del foco se desprende de su base o pierde adherencia y esto hace que no se mueva una lámina que libera la luz sobre la lupa viéndose afectada la luz alta.

[@rybreading]

Just pulled the front bumper and assemblies. Wish I’d have watched this first

[@ravenfrazier2236]

How do you change the bulb for the running lights

[@firstinlastout]

Were you able to find out the location for the DRLS?

[@IIAnonymousYTII]

Did you end up replacing them?

[@utherpendragon4227]

Turn counter clockwise to release

[@kylesimpson8402]

If you have big hands don't bother.

[@IIAnonymousYTII]

Where there is a will, there is a way.

[@dawit9686]

I did it.gracias

[@davidbrowne3102]

I can barley reach any recommendations before I go somewhere to do it. Thanks for the video

[@sophonhang7527]

Thank u

[@delavishagrimes5647]

This video doesn't really help at All I appreciate it you keeping it short and simple I just don't know how to change it I've been doing everything your video showed me before watching this so it wasn't much a help 😔

[@stevenhickey326]

Righty-Tighty Lefty-Loosie

[@ivansuarez9993]

It is not esay...

[@IIAnonymousYTII]

I started crying while attempting to do this since it is too hard.