Describe process for changing a filter valve gasket.
Пікірлер: 23
@rnarinesingh64 жыл бұрын
Can i use silicone instead of the glue?
@truelightpoolsllc44414 жыл бұрын
Silicon may work, but you would have to let it completely dry to hold the gasket in. I have heard of techs using it and the gasket came right out, they didn't let it dry. Also the tech told me the gasket came out after multiple backwashes and then the repair had to be redone. So that's why I don't use it. With super glue, it dries within 10 min and then you can start the system again and know it's there and secure.
@omarrivera6161 Жыл бұрын
I have a question regarding a leak in the head dome , it’s leaking from the top
@truelightpoolsllc4441 Жыл бұрын
Either replace the whole key assembly section or you can get a rebuild kit to rebuild the internals of the key assembly center section.
@tigerfish9499 ай бұрын
Can I just apply silicone if I do not have a replacement spider gasket?
@truelightpoolsllc44419 ай бұрын
It won't seal correctly.
@niloychakraborty5 жыл бұрын
Please comment -> What tool did you used to take the old gasket out.
@truelightpoolsllc44415 жыл бұрын
I modified the tip of a thin screwdriver by bending it and sharpening the end.
@thedude8609 Жыл бұрын
Is the same procedure for a sta-rite cristal flo?
@truelightpoolsllc4441 Жыл бұрын
If you have a valve like the one in the video that has a gasket glued into the track as shown, you can remove it and replace as shown.
@mytexasdays15265 жыл бұрын
How do you remove the glued in spider gasket? Mines stuck. No help from acetone, alcohol, razor. I'm getting to close to damaging the plastic with a razor.
@truelightpoolsllc44415 жыл бұрын
I use a flat screwdriver with the end bent like I show at the end of the video. But yes, scraping the old one out and prepping for the new one is where the work is done on replacing a spider gasket.
@oldrmike11952 ай бұрын
Still, I am unable to get my gasket out and clean the surface and I’ve tried a blow dryer and alcohol solvent to no avail.what now?
@corystef31133 күн бұрын
That’s because this guy is an idiot. Never apply super glue to a gasket. The entire housing now has to be replaced.
@corystef31133 күн бұрын
Super glue? My pool company said never use super glue. It’ll cause a hardened buildup that will be impossible to get back out when you need a new gasket and would actually cost most to replace the entire housing.
@jazzfan303295 ай бұрын
Doesn’t the new gasket need to cure ?
@truelightpoolsllc44414 ай бұрын
The glue needs to cure some yes. You can always let it cure and then come back next day to turn system on.
@ACommenterOnYouTube Жыл бұрын
It is a PITA to remove the old gasket material ...
@truelightpoolsllc4441 Жыл бұрын
Many times yes.
@userbosco3 жыл бұрын
Weird how some say use super glue, some rubber cement, some Loc-Tite... no consensus.
@truelightpoolsllc44413 жыл бұрын
Yep, that's what I use.
@danielklem87272 ай бұрын
If the handle was moved from closed to backwash to rinse and I forgot what position the handle was in when I removed the valve, putting the notches together will still be in correct position? Or did I screw myself
@truelightpoolsllc44412 ай бұрын
Line up the notch on the side of the filter valve top with the filter valve base, this helps everything line up.