Very impressive! Detailed Step. I am about to undergo this procedure though I have done it a dozen times before with different model of vehicles, this video will help. Thank you creators! I hope you make a million:) P.S. to other comments, yes there are always rusty old bushing bolts that don't come out and entire components need replacing. I like this video because it shows you how the procedure should be done. Will save an hour or two from either not removing the required parts, or from removing parts that are not required to be removed. Even included torque settings, brilliant! Thumbs Up!
@autodocuk Жыл бұрын
Thank you for your feedback! We are pleased to know that our video was helpful for you.
@MrZimmaframe2 жыл бұрын
Warning for anyone who wants to do this job, 4:47 see how by using the axle bolt to force the retaining clip in it can bite bits of the retaining clip off as seen in the close up of the retain clip, if you do not thoroughly clean all the old grease and and inspect the housing, any metal bits left in the housing can damage the ball bearings and housing of the joint which will make noise and will need the whole joint replacing. So make sure no metal bits, clean and inspect the old joint thoroughly. Also put the majority of the grease in between the ball bearing and joint housing, not in boot as it won't be used to lubricate.
@timothyjames62103 ай бұрын
Outstanding job. Great video
@sethnewman15526 ай бұрын
Good job. Nice and clean workmanship!
@shangosaeed32292 жыл бұрын
Nice
@b4tm4nrubin33 Жыл бұрын
I’d be putting the rest of the grease into the rubber boot
@alexey99003 жыл бұрын
Good 👍👍👍🏅
@garywilson774510 ай бұрын
Looking at the old CV joint at 4:17 was the plastic spacer and metal washer the right way around?
@autodocuk10 ай бұрын
Yes, everything is installed correctly.
@markchandler001 Жыл бұрын
In the required tools list at the beginning it says a Tap Wrench is required but I cannot see when he uses it. Was this an error in the listing?
@autodocuk Жыл бұрын
Starting at 9:42 you can see where the mechanic used a wrench.
@Liveforeever3 жыл бұрын
That cv joint was way undergreased. Some tips on the upper arms removal would have been helpful if the bolt is seized which it normally is 99% of the time.
@autodocuk3 жыл бұрын
Thank you for sharing your experience, it will be very useful information for us and our viewers. AUTODOC
@alabinibop3 жыл бұрын
Just been through that pinch bolt nightmare myself! Had to take the hub of completely.
@osamamaddani3 жыл бұрын
there is a specialized fork for removing suspension ball joints and tie rod ends, it looks like a giant tuning fork 😂, some antisieze spray and prying will get it out
@janus37592 жыл бұрын
Yes that bolt is always stuck. It is better to loosen only the outer tie rod to get axes to remove the cv joint. If the upper bolt needs to be removed, for example to change the control arms: use a lot of penetrating oil, remove the nut and drive the bolt back and forth with an impact until the bolt loosens.
@leradze7125 Жыл бұрын
mine broke, had to drill it out. took way longer than i care to admit. if i do this job i wil remove the lower arms instead.
@Jack_JJS3 жыл бұрын
Great video 👍
@yasinarslan968 Жыл бұрын
😮😮 super ❤️❤️🤍🖤
@santoscruz1304 Жыл бұрын
What's the cost for cv joint
@nikolaadamovic34993 жыл бұрын
For what reason do they spray that bronze color on the screws and the part?
@autodocuk3 жыл бұрын
Thank you for following our channel. They spray meticulous spray so that the spare part would sit well and in the future would not become attached and it could be easily removed in the event of a breakdown. AUTODOC
@MrZimmaframe2 жыл бұрын
Copper grease is an anti seize, it will help prevent things from seizing together if the part needs to be taken apart in the future.
@revengex51633 жыл бұрын
Same Tutorial for A4 B8 ?
@autodocuk3 жыл бұрын
Thanks for your feedback! Please clarify or rephrase your question.
@-mohammeddays40153 жыл бұрын
💓💓💓💓💓💓
@Planetary132 жыл бұрын
I don't know what I did wrong. I impacted the bolt in to separate the cvj and it did not come apart and now the bolt got stuck when u impacted it out. Wtf?
@autodocuk2 жыл бұрын
We do not have such information, we recommend that you consult your mechanic.
@Planetary132 жыл бұрын
@@autodocuk I'll use a press to get the cvj apart from now on. I feel I had bad luck on this joint
@vandalsgarage10 ай бұрын
If the removed bolt isn't long enough to reach the end of the stub axle, it will simply tighten against the cv joint. Do not use the impact gun to tighten it against the cv joint! Remove the bolt, and insert a 4" long, 1/2" diameter steel rod. You can sacrifice an old 3/8" ratchet extension if you don't have anything else. You are going to run that steel rod through the CV joint, and into the stub axle about 2", leaving the same amount protruding into the CV joint. That will be plenty for the removed wheel bolt to push against. Note!!! Once you've sent that steel rod into the CV joint, you're committed to removing the cv joint. Once you've got something for the bolt to push against, you should be able to literally spin the bolt with your fingers to back the cv joint off the circlip. No need to use an impact.
@Planetary1310 ай бұрын
@@vandalsgarage Thanks. I'll do that in the future. I'm pretty sure the bolt was long enough. At least the cv/axle I damaged was an aftermarket. I installed a rebuilt OE axle in its place. Thank you for the reply.