How to Change Number Plates // Number Plate Holder Installation

How to Change Number Plates Including New Number Plate Holders. New pressed plates and number plate frames will make a HUGE Difference to how your car looks!
I this video I remove my old, damaged number plates and install new pressed number plates into new number plate holders.
I’ll show you exactly where I bought them just in case you want something similar. I’m not affiliated with these companies by they supplied me with good products and had good customer service:
🤝 Suppliers
👉 AE.Trade (Ebay seller) www.ebay.co.uk/str/aetrade1 They have a wide range of number plate holders. The ones I bought were called: Domed Gel BMW M POWER Silver
👉 Plates For Cars www.platesforcars.co.uk/ Pressed Metal Number Plates
- SUPPORT -
If you like my work and want to help to support this channel you can use the link below and buy me a coffee. Thanks!
www.buymeacoffee.com/ReviveMy...
Or maybe give me a THUMBS UP! 👍 👍 👍
💥 Please consider SUBSCRIBING for MORE Great Car Content!: 👉 kzbin.info...
🙏 If you want to SHARE this: How to Change Number Plates // Number Plate Holder Installation PLEASE use this LINK: • How to Change Number P...
00:00 How to change number plates
00:17 Remove number plate
00:33 BMW number plate surround
01:10 BMW Number Plate Frame
01:20 BMW M number plate Holder
01:49 Install number plate Holder
03:27 Where to buy Pressed number plates
03:38 Pressed number plates
04:17 Install pressed number plate
05:17 Change number plate rear
05:27 Number plate holder fitting
DISCLAIMER - Please note that this video and its content is intended for information purposes only. Although every effort is made to ensure that all the information is correct, there is no guarantee that this is the case. This video should not be considered a substitute for seeking independent advice or the services of a professional. Any work that you carry out on your vehicle or vehicles in your care are at your own risk.
Affiliate links - This video description contains affiliate links. If you click and purchase, I may make a small commission (At No Cost to You). I only recommend products and tools that I use, or would purchase and use myself!
#changenumberplate #numberplateholder

[@ReviveMyRide]

If You're Trying to Spruce Up Your Car, This Video May Interest You! 👉How to Get Rid of Scratches on You Car kzbin.info/www/bejne/nZ6bi5Whg6mag8k

[@martinramsey114]

I always get these pressed plates whenever I get a new car. I think they look great. I also like the brand names on the holder on German cars. My previous car was an Audi A4 Avant, it was straight forward putting the plates on that. I now have a Mercedes C Class. The front has a bit of a "V", I just wondered how much flexibility is in the plate and the surround. I should probably be asking someone who fitted them to a Merc.🤔

[@ReviveMyRide]

Hi, as it happens, we have a C class too but I haven't fitted the plate holders to it. It's my wife's car and she just likes normal plates on it. However, I think the holder could be made to fit and follow the "V" shape but you would probably need to drill a couple of extra holes either side of the "V" and add securing screws there to make it conform to the shape. Depends on how you feel about drilling extra holes. Following that, metal plates are very flexible, so I'm sure you'll have no problem putting a small bend into them in the middle.

[@martinramsey114]

@@ReviveMyRide I'll let you know how I get on with it.

[@vipboss82]

Great 👍🏼 Video. Very Useful, Just One ☝🏼 Question 🙋🏻‍♂️ The Backing of The Number Plates Made From PFC Is it Nikkalite Reflective They Use ? Thanks ☺️

[@ReviveMyRide]

Hi, Sorry, I've no idea regarding what backing material they use. Maybe drop them a quick message? Their contact page is here: www.platesforcars.co.uk/contact_us.html Thanks, Phil

[@johnryan4485]

Hi there. Have you any video of how to take out the number plates from the plate cover/frame? Also how to open up the bottom of the cover?

[@ReviveMyRide]

Hi, at the bottom of most of these types of plate holders, there is a strip that you click into place with push studs. I think you could get a trim tool (ideally) or a flat bladed screwdriver between the strip and the backer at the bottom and lever it, working your way along to unclick each of the push studs. Hope that helps!

[@OwenN98]

@@ReviveMyRidethank you! I was struggling with this as I didn’t know any to break anything - you saved my day

[@johnterry6594]

hi my back plate no screws holding on with tape or something whats the best way getting it of without damage

[@ReviveMyRide]

Hi @johnterry6594 I would try heating up the backing plate with a hair dryer for a good 5-10 mins, this will soften the adhesive (this is much better than a hot air gun, which can get too hot if you aren't careful and damage the paint). Then us a plastic lever of some kind (trim removal tools are good for this) and see if you can peel it off of the bumper. Hope that helps! Thanks, Phil

[@Shaolinblo]

hey I've got same holders installed but how do I remove the bottom lock? I cannot change my plates again once I've locked it in. any advice?

[@ReviveMyRide]

Hi, if you’ve got the same type as the ones in video, then the bottom lock has three or four press stud fittings across its length and then tucks behind the trim on the left and the right. My device would be to start in the middle of the bottom lock and lever it away using a trim tool until you can get your fingers behind it. Hope that helps! Thanks, Phil

[@Shaolinblo]

@@ReviveMyRide thank you I was trying to push from behind hurting my finger tips I'll give that a go they look pretty locked in and I don't want to snap the bottom frame

[@ReviveMyRide]

@@Shaolinblo Yes, breaking it is the risk. If you can figure out / feel where the central press stud is and lever directly where it is, between the plate (use masking tape on the plate if it is a metal one) and the bottom frame you might be able to do it. Good Luck! 🍀

[@tol7488]

In the north we use metal frame

[@ReviveMyRide]

😂 Everyone further up than the Midlands thinks that they are in the North in the UK! I liked this plastic one because of the gel / M logo printing, although I just checked and yes, there are some nice chrome and stainless steel number plate surrounds out there! 👍

[@martinramsey114]

@@ReviveMyRide Further up North, I'm going to use this one.