This video will show you how to remove intake manifold to access your ignition coils and spark plugs that are underneath the manifold. 2.7L V6 engine from year 2006 and up.
Пікірлер: 42
@Reggied1030792 ай бұрын
Best explanation I've seen so far. I'm about to do this at some point this week and changing out all my coils as well. My engine has been shaking a lot when I'm idling and somebody told me that would solve it.
@marcussmith63132 жыл бұрын
Great job! I like how you showed step-by-step actions for manifold removal, hoses, sensors and spark plugs. I'm ready to change my plugs now!! Thank you
@silverbullet_2ss2 жыл бұрын
You're very welcome KZbin Fam! Good luck with the process 👍🏾
@dirkdurant91 Жыл бұрын
Good video man. Gonna do this to my 2010 charger tomorrow and needed a heads up on how to do it. Thx
@silverbullet_2ss Жыл бұрын
Thanks man! Glad I could help out! Let me know if I missed anything.
@chriskelley5066 Жыл бұрын
I know this was way past the video that you put out but I want to know what tool you used to unscrew the spark plugs?
@silverbullet_2ss Жыл бұрын
If I recall right, it was a torxbit T25, T27, or T30...🤔 can't remember.
@chriskelley5066 Жыл бұрын
@@silverbullet_2ss Thankyou for following up with me.
@silverbullet_2ss Жыл бұрын
@Chris Kelley you're welcome. Thanks for the view. Hope video helps you get the job done.
@bensocrazy72642 ай бұрын
Thanks bro. Bout to change out my daughters spark plugs. I’m glad it’s easy to do. How’s that aftermarket part doing? What’s the effect it has on your car?
@froylanmiranda7362 Жыл бұрын
Only one concern you didn't cover the intake manifold holes. Other than that I would replace everything under that intake manifold (EGR valve, PCV valve, coils, plugs, gaskets every gaskets. I use pre gapped ngk don't know why parts fail after a year or two on these cars
@forde.76959 ай бұрын
Whats the ignition coil number order ?
@BWil-n3fАй бұрын
Wat gasket is dem
@gohardproduct5 ай бұрын
I PUT A RAG OVER THAT
@keil2clean7922 жыл бұрын
Did the exact but mind want start
@silverbullet_2ss2 жыл бұрын
Any luck getting car started?
@rochellej39005 ай бұрын
Who can do mines coming from the u.s 😮
@rochellej39005 ай бұрын
So serious
@SLINGING_MUD_SINCE1994 Жыл бұрын
Great job bro
@silverbullet_2ss Жыл бұрын
Thanks KZbin Fam!
@SLINGING_MUD_SINCE1994 Жыл бұрын
@@silverbullet_2ss yessir
@BWil-n3fАй бұрын
Wat socket nd tools are u using to take da spark plugs out with
@silverbullet_2ssАй бұрын
@@BWil-n3f 5/8 sparkplug socket with 3/8 ratchet and telescoping 🔭 magnet 🧲
@juliorenegarcia98632 жыл бұрын
Travajo con la misma computadora
@donialsfogg58012 жыл бұрын
Good Job my Brother!👍🏽
@hectorlucero9158 Жыл бұрын
Did you use any antiseize or dielectric grease
@silverbullet_2ss Жыл бұрын
I did not. Wouldn't be a bad idea.
@hectorlucero9158 Жыл бұрын
@@silverbullet_2ss just changed the spark plugs, video helped a lot thanks man
@silverbullet_2ss Жыл бұрын
@@hectorlucero9158 thank you for watching!
@juli79702 жыл бұрын
How similar is this to the process of changing the plugs on an 07 Magnum 2.7 l?
@silverbullet_2ss2 жыл бұрын
They are essentially the same car with same engine setup. The differences between them would be minimal and mostly aerodynamics. You got this! 👍🏾
@juli79702 жыл бұрын
@@silverbullet_2ss 👩🔧 I just bought the vehicle, should I swap out the coil packs as well? Since I'll already be fussin about in there? Also, great job thanks for being so specific but not overly long-winded!
@silverbullet_2ss2 жыл бұрын
@@juli7970 thank you 😊! I really appreciate that! As far as coil packs, I would change them out based off age of vehicle and mileage plus a set of coils is not expensive depending of where you buy them.
@juli79702 жыл бұрын
@@silverbullet_2ss gotcha! 1 more (I think) question:. Can the injectors in cylinders 2,4,or 6 be changed without removing the plastic thing that reads "2.7L V6"? Plennum i think it's called
@silverbullet_2ss2 жыл бұрын
@@juli7970 unfortunately no. You'd have to remove it (intake manifold/plenum) in order to access the fuel rails. Then, remove bolts from fuel rails that seat inside the lower intake manifold (black plastic w/ orange gaskets) then you can pop injectors out after that.