How to change the fuel injector seals on 1uz vvti and 3uz engines.

[@AY-nh1ek]

Thank you Kelvin, seeing this video i discovered gas leak caused by no gasket washer in injectors rail. Wonderful discovery❤

[@alexmax6050]

Very nice. Did it the last week. Thank you for your video. They had help me much. I have no rubber greace, and was afraid of silicone spray. Toyota manual said to lubricate the wachers with gasoline before instalation in the Mainfold. I did it and hope it will be ok.

[@B1u3d0g6]

I wish you'd do some more on the 2uz. Whilst I understand there are differences between all generations of UZ you cover the 1 and 3uz extremely well. The details you provide are invaluable and I kinda wish you were an Aussie. I'd be at your joint tomorrow

[@CartuneNZ]

The thing is 2uz aren't common here, hence I dont do much with them.

[@brianblank82]

I changed the little cone filter at the top by placing an appropriate screw in a vice screwing the injector cone basket onto the screw then pulling it out like a cork. inserting a new one with a light tap until seated

[@brianblank82]

I used for early 1994 sc400 - GOSS Injector Repair Kit IRK704 102311-IRK704 $12.95

[@CartuneNZ]

I should really have covered that too but there was a lot to cover on this one. Cheers

[@3uzSwapped55]

Hey Kevin! Do I need to replace the fuel damper gasket kit everytime I take them off?

[@bvward]

Kelvin, thanks for the tutorial! Gotta do seals on my Miata, Switching to Bosch 1000cc ones ;)

[@salmanhusain8665]

I recently got my injector serviced professionally and got all the O rings, filter and cushion replaced. After it, on one bank, the injector are having Vaccum leak. I have cleaned contact seats retighten bolts etc. Still there is an air leak. What can be the reason?

[@richardzigman]

Thank for good video.

[@CartuneNZ]

Thanks for the compliment. Cheers Kelvin

[@V8TezzaBoss]

Can you do a video to fit normal injectors to a vvti manifold please

[@CartuneNZ]

Yes. Doing that at present.

[@V8TezzaBoss]

@CartuneNZ am like do waiting for it and please include drop injectors for up grades too

[@dentasla]

Thanks Man

[@laboyx4753]

Do you know the part number for the crush washer that goes in between the bottom of the banjo and the fuel rail? Or can I just use a normal washer

[@dentasla]

Spirit💫

[@NorthWesTrav253]

Random question: I have a 95 Celsior 1uz and it randomly stalls out after a long drive on the freeway. At first I thought it was the air filter, but I have no clue where to look. Any tips help. Thanks

[@nct9466]

Usual diag process..... Can’t do anything remotely much really...

[@nct9466]

“22mm spanner” in bald eagle terms it’s “22mm wrench”..... Just a translation interpretation for those folk that need it.....

[@SteveCrawford-r2d]

Please help me find the rubber tips that seal in the manifold ( seal takes shape of lower injector) NEED PART NUMBER PLEASE AND WHERE TO ORDER - I am based in South Africa and Toyota can not help me and supply wrong part - Tried Denso as well. Injector is 23250-50010 I have seen these Denso numbers as well that could be compatible 23209-50010 Denso 5490 / 19500-5490

[@alexmax6050]

Hi. I had a number of things that I found on RocAuto Seattle's in the USA. They ship worldwide. They are not original but if you choose not the cheaper ones the quality would be good. The seals that I bekam were made in Japan.

[@tedbastwock3810]

You missed your calling ... You should' ve been a comic to support your u-zed engine obsession

[@CartuneNZ]

Im glad someone gets my humor, or humour depending on your location. Cheers Kelvin