This video is SUPER helpful! And the tie is very fancy!
@juliebates68188 жыл бұрын
Thank you! I watch this every time I have to change the rolls
@mybinding8 жыл бұрын
+Julie Bates Glad to help! If you need any more help, or need to buy any new rolls, be sure to call us or check out our site at Mybinding.com!
@KevinMarshall-vk4sp Жыл бұрын
EASY TO USE EVEN FOR BEGINNERS
@redvelvetvictorian94938 жыл бұрын
use this video everytime I replace a roll!! Thank you
@homesickpolarbear7 жыл бұрын
Thank you for this video. Going through step by step is very helpful. The only step that could have been explain, just a little better, was the bottom bar that had to be lowered for the bottom film to be wrapped around. I found how to lower it by accident. Otherwise everything else worked like it shoud. Thank you again for this instructional video.
@brendadurbin67783 жыл бұрын
,,* a hkk m m*z mmmmm mmm,k j&. m hmm m m k m m mmmmm. mm. NM mm,. mm mmmmmm mh m mmmmm . & mmmm m mmmmm. mmmmm. mm mmg . m mm. mm m m zzz m h zzzh,
@TheTechnologyFox12 жыл бұрын
At point 556 in the video both heat rollers should be overlapped. The video is not clear that the shiny side should face out and the operator, or the dull side. I believe it really matters and would save hours of frustration. I urge this company to redo this video, then have someone who knows nothing try and follow the video. Do that 10 times, with no questions asked it is will improve the usefulness of the video. As well, the manual should have the same stipulation.
@DebCool Жыл бұрын
Did not show how to get what u rolled across so have to replace a roll? I need to know how to get the item I rolled across off roll
@KariBoardman9 жыл бұрын
Video helped me! Thank you!!
@ruthsullivan1598 жыл бұрын
video helped me - Thank you
@TheTechnologyFox12 жыл бұрын
34 second into it says the shiny side- but which way do you load it to achieve it.
@longmontanalytics52157 жыл бұрын
What happens if the heat rollers get glue on them? We had someone misload one of the rollers.
@mybinding7 жыл бұрын
You are going to need to clean it off. The best way is to heat the laminator up and then scrub it with a scotch brite pad (the green and yellow ones). All the adhesive needs to come off and it takes some serious elbow grease. Just be sure to NOT use anything sharp. It can ruin the rollers.
@longmontanalytics52157 жыл бұрын
How do I take them off to clean them? Or do I do it on the machine?
@mybinding7 жыл бұрын
You will find that they are the easiest to clean if you have the machine on and the rollers turning when you are scrubbing. The heat will soften up the adhesive. Just be careful and use gloves so you don't burn your hands.
@longmontanalytics52157 жыл бұрын
It worked, but you're right -- lots of elbow grease required! Thank you.
@mybinding7 жыл бұрын
Glad you were able to get it cleaned up.
@ernestcaravalho90747 жыл бұрын
And for crying out loud...tuck your tie or lanyard in when pretending to be a lamination tech!
@TheTechnologyFox12 жыл бұрын
Have 10 other people who have never used anything like it follow the directions and see what it doesn't explain or allow. Both really need work.
@ksingles6035 жыл бұрын
Shaft was said a lot
@TheTechnologyFox12 жыл бұрын
Poorly done video. Directions like facing you or away from your mean nothing. Which side is the shiny side? Too many questions unanswered. But I must say it is ten times better than the manual that came with the machine or is downloadable from the site. I don't know if other companies do it better, but experience people stil spend 2.5 hours replacing something that should be a 15 minute job. poor company, poor video.