If you go for the black rubber, are you meant to put in a 40mm pushfit pipe or you are allowed to push in 40 mm solvent weld pipe as well? Will if fit and is it OK by water regs?
Excellent all I need to connect my waste pipes in one easy lesson. Thanks for you time.
@tigertruckerman20 күн бұрын
I was going to ask about the fall,from waste pipe into the strap boss
@christopherhagans4488 Жыл бұрын
Hi Tommy I would be so great fully for help can you get a pipe that would be different size at ether end like a rubber would be more flexible i guess so say the pipe one end would be 10cm an other 6cm to fit in to mu gutter running outlet down spout many thanks
@mrtaktiks Жыл бұрын
Thanks for your work. I have unearthed my clay sewage line and wish to tap into it and add a dog waste sealed PVC pipe. Any advice. Thanks
@nerdimmunity7672 Жыл бұрын
My Waste pipe that goes into my soil pipe keeps getting blocked!
@stuntmanwill4 жыл бұрын
Hi, I need to block off a boss strap hole as have got rid of the pipe going to it, is there a push fit cap that goes into the boss hole available?
@sahinahmod83844 жыл бұрын
Hi my soil stack is internal . I was wondering if I could just replace the top half of the soil stack with a Tee joint which would allow only the top half to be showing outside , is this a good option to choose ? Or would I have to completely remove it & put it outside ?
@richylad5 жыл бұрын
thanks, just came to see how far i needed to push my waste pipe through the boss, thanks for the info, spot on.
@jimh40725 жыл бұрын
Me too, I was not sure about how far either.
@atommachine4 жыл бұрын
i have a 60 mm class c pipe from a pump do you know how i can connect it to the boss or soil pipe thanks.
@notnotbow3 ай бұрын
Brilliant - answered all my questions!
@inthemix30134 жыл бұрын
I have water feeding back into the toilet from the connecting pipe. It leaves a dirty brown water in the toilet every morning. Any help much sppreciated
@inthemix30134 жыл бұрын
The pipe that leads to the soil cheers
@Drifter0773 жыл бұрын
How to connect drains to gutter pipe?? Thanks
@Alfapash7 жыл бұрын
great explanation, cheers.
@SuperBlackguard2 жыл бұрын
Nice one! very handy information,cleared a lot of things up
@Cloppa20006 жыл бұрын
I can't get my rubber boss adaptor in to the existing pipe boss. It's way too tight! Is there any way to trim the rubber boss? I dont have room to fit an extra strap boss.
@desgosling28762 жыл бұрын
Thanks for all the exclllent videos.
@billburr13477 жыл бұрын
Thanks fella, much appreciated for the helpful video
@edrobens51455 жыл бұрын
Can a boss pipe have waste entry on opposite sides? Would this infringe the "no connection zone" rule for opposite entries into a soil pipe?
@Spongesyellow9 жыл бұрын
Have you got a video for installing a mechanical boss pipe? We had a strap on boss...it leaked causing staining on a new ceiling....then had a mechanical boss fitted..now that's leaking! help!
@solefreak25 жыл бұрын
Is it okay to run a boiler condensate pipe into the soil stack using the strap boss? I'm just concerned that any toilet/bath waste could potentially run up into the condensate pipe and into the boiler.
@S20Mike5 жыл бұрын
It largely depends on where your boiler is located in the waste system; if there are outlets below the level of the boiler, assuming any blockage has occurred after the last outlet, any backing up will discharge from that outlet, like your toilet pan. If the boiler sits below the other outlets, then anything backing up will fill the boiler.
@solefreak25 жыл бұрын
@@S20Mike Boiler sits on the ground floor so below the toilet and bath etc. Is there any type of pipe that can be used that would stop water/waste from backing up into the boiler? Like a non-return valve?
@hassancooling87887 жыл бұрын
bro thanks a lot of... really you solved my 100000000 problems in one videos amazing...
@jimreid6797 жыл бұрын
Very well executed Tommy couldnt have done it better myself will 20 out of ten do
@Bananas331 Жыл бұрын
Perfect, thanks.
@nicoteen9407 Жыл бұрын
Brilliant. So concise!
@hamz30986 ай бұрын
Excellent job
@smalik6953 жыл бұрын
Very nice 👍
@ashy14234 жыл бұрын
Thank you 👍
@877cms4 жыл бұрын
Thank you!
@ranveersingh-zq3hq5 жыл бұрын
Very helpful Thenk you
@whopaimon54077 жыл бұрын
Briliant, very nice video
@siobhancosgrove41456 жыл бұрын
An EXCELLANT video
@stevengreen40427 жыл бұрын
Thanks, really useful
@leewilliams9559 жыл бұрын
Excellent explanation
@tonyeverden8 жыл бұрын
Very helpful
@222vaux36 жыл бұрын
Thanks
@frank18478 жыл бұрын
Brilliant ! .
@yoislam8 жыл бұрын
Top man
@alistairmorrish86136 жыл бұрын
if you're solvent welding, just push the pipe straight in - DON'T GIVE IT A TWIST - that is bad practice - you break the joint as it is setting...