How to convert your lift start plasma cutter to PILOT ARC!! Easiest way on YouTube! DIY

On this episode of Mad Ginger Customs we finish off our plasma cutter series with an awesome easy modification!! This is by far the best and easiest way to convert to pilot arc you will find! This will work on virtually any lift start machine to give you a pilot arc!
AG60P pilot arc assembly amzn.to/3R6Tecw
Plasma cutter shootout and Arccaptain CUT50 giveaway!
• Budget Plasma Cutter S...
Bestarc BTC500 video
• Bestarc BTC500 review ...
If you like our content, you can buy us a coffee here!
bmc.link/madgi...
Hit that SUBSCRIBE BUTTON!!
Support the channel!!! Here are some of our favorites from amazon! If you click and/or buy, you support us!
Tipping die set for bead roller amzn.to/3QJgSMD
Ratcheting wrench set amzn.to/3J0MGXL
Ospho Rust Converter amzn.to/3SZiHnG
Best cold saw ever!! Evolution chop saw amzn.to/3ZSJ2pH
#diyprojects #diyrepair # #diy #welding #tigwelding #migwelding #btc500 #plasmacutting #plasmacutter #bestarc #simder #arccaptain #arccaptainwelder #pilot arc

[@zerobambiro]

I think you could just reuse the old torch and put a cable in there

[@madgingercustoms]

There is a little ignitor in there from what I can see but I suppose you are correct.

[@brianandglendaharkin9457]

👍🏻💯🇦🇺

[@madgingercustoms]

Thanks for watching this one!

[@wiggle73]

BRILLIANT!!!!!!

[@madgingercustoms]

Thanks!

[@alexchliwnyj5941]

NO, just NO.

[@madgingercustoms]

Yes. And yes. Cut an entire international pick up apart. Works great.

[@Isadore123L]

I like the way you break things down into the simplest terms so us backyard enthusiast with some time and determination can get the most out of what is on hand. Have my fingers crossed for hitting the jackpot on the ArcCaptain unit.

[@madgingercustoms]

Thank you! Good luck in the giveaway!!

[@ChrisGagnonDIY]

so smart and simple thanks

[@madgingercustoms]

Thanks for watching!

[@sevrovychodnithajsko8315]

If you understand electric side than you would know this way reduce power of the plasma. The correct way it is to disconnect the pilot circuit after the main current start. Try cut some thick metal with your improvement...

[@madgingercustoms]

I understand but the draw is so little it really didn't affect the usage. I ran 1/2" afterwards and it cuts just fine. Thanks for the heads up!!

[@katj6488]

Thanks Dave,nice to have someone who is willing to show us some money and time tips!!😊

[@madgingercustoms]

Thanks for checking it out. I may convert all of the ones I got!

[@SWResto]

I Sure could use the ArcCaptain plasma youre giving away!!

[@madgingercustoms]

Make sure you comment on the give away video in the comments!

[@janniegann2668]

Yeah I can't afford a plasma cutter.

[@madgingercustoms]

Check out the giveaway video and get in on that!

[@joeyholloway1515]

great video Dave, don't know how many times i can enter the giveaway but i would still like the Plasma

[@Yosser70]

Love this as I want to build a plasma cnc. Only question would be, with it beeing this easy to do, why don’t the manufacturers set them up like this? There must be some disadvantage or safety issues. I know the connection should switch after ignition, and keeping it permanent lowers power a little but not overly concerned about that, as i’ve no need to cut 10-12mm plate.

[@madgingercustoms]

The pilot version of this unit is only $10 more so I'd go that route.

[@barrymurray8264]

Thanks Dave ! Do you paint with pastels ? Be well.

[@madgingercustoms]

I could try that! Lol

[@ronsills4103]

Is the connector big enough to slide over the button on the "grounding" lug? If so, why not just put the connector over the button on the ground cable plug it back in and you've basically done the same thing with zero tools needed.😊

[@madgingercustoms]

It won't lock in. I tried that first.

[@jimalmeida7999]

Will the same procedure work for the Arccaptain CUT50 unit

[@madgingercustoms]

Yes but the Arccaptain has a push on switch connector not a screw on so you just need to swap that over.

[@GunClingingPalin]

Put the wire in first.. then push the copper hard end in.. much easier folks :)

[@madgingercustoms]

Whatever works for you!

[@Tubeagrutis]

Friggen' awesome!!! Really glad the YT algorithm suggested me one of your vids a few weeks ago. I subscribed then, and have been getting caught up with all your vids.

[@madgingercustoms]

Thanks for checking out the channel! We appreciate it!

[@lodwill5116]

Why I don’t just buy the right machine with the right torch??

[@madgingercustoms]

It was supplied by the manufacturer. They sent a lift arc so we did a budget shootout with other brands.

[@danobrien3109]

That’s so simple even I could it. Thanks Dave from your HVAC brother in the north.👍👍🇨🇦

[@madgingercustoms]

Thanks for checking out. It's crazy how easy it is.

[@arthurprice-ju7lj]

Plasma cutter would be nice to have if they weren't so expensive

[@madgingercustoms]

Get in on our giveaway in our plasma cutter shootout video!

[@BillupsOMally]

Saving for future reference. Thanks.

[@madgingercustoms]

Thanks!

[@brandescm]

Lots of slots, in your video!

[@madgingercustoms]

What's that mean though.

[@brandescm]

@@madgingercustoms Beavis and Butthead Do America had reference to lots of slots. You used the word slots a few times. Just stupid humor.

[@revmsj]

I’d sell my plasma to get a plasma cutter if you don’t give me that free plasma cutter…

[@slakjawnotsayin5451]

They're only about $250 on Amazon.

[@terrykeithley6183]

Thanks Dave, regards to Jess.😊

[@madgingercustoms]

Thank you for checking it out. I'll let Jess know you said hi!

[@faroironandcustoms6577]

Cool!!!! Maybe my torch is burned out. The pilot arc hasn't worked in a while. I did not realize that is what that connection is for.

[@madgingercustoms]

Yes sir!! There is just an ignitor style unit in the torch.

[@faroironandcustoms6577]

I already ordered one!! Wil test it when it gets here!!

[@alonsoochoa6218]

can i use this torch on a Herocut Plasma Cutter, 35Amp

[@madgingercustoms]

Judging by the pictures on Amazon, yes you can!

[@alonsoochoa6218]

@@madgingercustoms thanks for answering, I will try it

[@Ron_Lockwood]

Thanks for the advice.❤

[@madgingercustoms]

Thanks for coming back and watching!!

[@VintageTinGarage]

Great info, thanks

[@madgingercustoms]

Thank you!

[@clintlegeyt4835]

Solid vid

[@madgingercustoms]

Thanks man!!