How to do basic configuration of deep sea controller DSE 7310 modules

[@augustmushi5743]

Thank you so Much for Sharing this with us ! Be Blessed

[@CharlesRolpukia]

I feel like I want to learn more on the deap sea configuration..thanks so much

[@CharlesRolpukia]

Thank you so much may God bless you and your family ..so helpful brother..thanks, thanks, thanks so thankfull

[@maqsoodahmed8043]

Superb explanation

[@vipulaanuranga6717]

Excellent video 🎉

[@mohibullahahmadi900]

Hi, how we configure the Chinese DSE display with new software 2010 I tried to configure the Chainise made DSE display but the 2010 software did not open it so please inform me Thanks

[@abudhakir9403]

Thank you so Much for Sharing

[@evatontechnologies3297]

very educative program

[@electricalmastar]

Thank you

[@jaimetemplo3726]

brod how to print of load bank result during you are doing the load bank test record

[@malikibrahim1124]

Please make a video on electronic Guage configuration thanks

[@nasirrehman3854]

Best work

[@deathshane1]

Can you guys show detail wiring of auto/stop and the programing

[@sujonmehedi5359]

Hi sir my generator deep sea controller didn’t show any think but come out alarm. in that case what can I do?

[@mrmechanic2802]

Thankz😇

[@abdulhaqabid281]

Please make a video of 6110 rth mkii 2.0

[@naushadmohammad2784]

Any sample program for ATS control sir.

[@ehsanqayuomi9957]

Thank you very much.. From which one software we used in pc

[@electricalmastar]

Thanks for your comments and i used DSE software you can directly download it from dse website

[@harrissonramirez9448]

buenas como esta tengo dudas con un dse 6110 el display se ve verde y no puedo observar los parametros

[@zpmcborouge141]

hi, i installed this software in my windows 8 system but its showing error of "failed to locate the main config suite application. A software upgrade is required." Can you tell me the solution of this error.... please help in this...

[@electricalmastar]

Hi thanks for your comments, Did you follow the same steps which I was mentioned in that video and if it's asking upgrade then try it may be it will work Thank you

[@mitkuberhe4074]

u right click on the shortcut icon then locate the file location ,then there u get an update application in the directory then after u finish updating it will work correctly.

[@varadarajanu]

Sir if deep sea fault how we can run auto manual ,? We can repair ?

[@electricalmastar]

Thanks for your comments Mr. Ullal varadaraj, in case deep sea failure you can run it manual mode easily and troubleshooting of deep sea I will make separate video soon. Keep support our channel 🙏

[@MohammedHShakr]

How can I upload configurable data? If I not configure or program this data Will I face problem?

[@electricalmastar]

Hi thanks for your comments and default configuration has installed in the controller and based on your requirement you can change it and uploading is very simple just connect controller to that dse software and click upload Thank you

[@arctonengineering6316]

How to eges to governor correct way

[@varadarajanu]

Sir our oil sensor heat sensor Fault how we make on generator & Auto not start ,our DSE 7110 Mk 2

[@electricalmastar]

Hi ullal varadaraj, If your DG sensor faulty then you need to replace it or if you want to run the DG you need to change the controller setting for sensor like disable it Thank you

[@ChanhYangkongjee]

Hi Sir how we configure expansion input section ?

[@fahadali311]

Remote start on load option showing blur but it is not used in other digital inout

[@topx29]

Where i can download the software?

[@electricalmastar]

Thanks for your comments and for download and installation please click the below link kzbin.info/www/bejne/gXjJoZR7d9urn8U Thank you

[@mackstone2912]

Why is my module when I press Auto the engine cranks instead of Auto mode

[@shabeerpasha2814]

What problem and how to remove the indication of memory croup cation refer to user manual

[@musman8352]

AOA how can change hour Meter reading dse 7310?

[@electricalmastar]

Hi thanks for your comments and connect your controller to dse software and reset the settings then it will count from beginning Thank you

[@pragnap3718]

How to program external automode enabled input used for remote generator breakers close output plus, please explain

[@electricalmastar]

Thanks for your comments and i will make separate video for your request soon Keep support our channel Thank you

[@Shayan_1234]

How make changes of hours

[@mahigogoi8190]

Sir eska settings kisikrta hai bata pawo ge

[@malikfaisal8295]

How to deactivate remote start input

[@markusgarvey]

What is a ''mastar''?

[@rimpookumarvishwakarma804]

how can made PLC of DSC7450

[@nuwanthilina5741]

is it support to caterpillar generators

[@electricalmastar]

Yes it could be supported for all generators

[@emmanuelchabi9904]

Comment peut on avoir le logiciel

[@minhtuantran6575]

how to set run time 7320

[@yasirkhan-bz8rl]

Sir how can i increase hours

[@sombathphilakoun651]

Hi please explain how about configure dse7320Mkii with Volvo machine ECU or EMS2

[@Uzmairdip]

Plz share sync configuration of 8610DSE

[@electricalmastar]

Thanks for your comments Mr. Sardar zohaib, soon i will make separate video for synchronization Keep support our channel , Thank you

[@Uzmairdip]

@@electricalmastar Sir thank You for your reply . But on up coming weekend i am going to performe ha Sync Job . I have little doubts in my mind related to 8610Mk programing. If you can help me related this i will be realy thank Full to you.

[@emmanuelchabi9904]

Et son Manuel d'utilisation

[@shabeerpasha2814]

DSE7320